Diagnostic Trouble Code (DTC) Chart
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| Module | DTC | Description | Action |
|---|---|---|---|
| ABS | B12F4:12 | Vehicle Speed Output: Circuit Short To Battery | GO to Pinpoint Test BH |
| ABS | C0020:11 | ABS Pump Motor Control: Circuit Short To Ground | GO to Pinpoint Test E |
| ABS | C0020:49 | ABS Pump Motor Control: Internal Electronic Failure | GO to Pinpoint Test AF |
| ABS | C0020:4B | ABS Pump Motor Control: Over Temperature | GO to Pinpoint Test AX |
| ABS | C0020:64 | ABS Pump Motor Control: Signal Plausibility Failure | GO to Pinpoint Test AX |
| ABS | C0020:71 | ABS Pump Motor Control: Actuator Stuck | GO to Pinpoint Test E |
| ABS | C0030:07 | Left Front Tone Wheel: Mechanical Failures | GO to Pinpoint Test AH |
| ABS | C0031:01 | Left Front Wheel Speed Sensor: General Electrical Failure | GO to Pinpoint Test G |
| ABS | C0031:07 | Left Front Wheel Speed Sensor: Mechanical Failures | GO to Pinpoint Test B |
| ABS | C0031:29 | Left Front Wheel Speed Sensor: Signal Invalid | GO to Pinpoint Test B |
| ABS | C0031:2F | Left Front Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test B |
| ABS | C0031:4A | Left Front Wheel Speed Sensor: Incorrect Component Installed | GO to Pinpoint Test O |
| ABS | C0031:64 | Left Front Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test B |
| ABS | C0033:07 | Right Front Tone Wheel: Mechanical Failures | GO to Pinpoint Test AJ |
| ABS | C0034:01 | Right Front Wheel Speed Sensor: General Electrical Failure | GO to Pinpoint Test G |
| ABS | C0034:07 | Right Front Wheel Speed Sensor: Mechanical Failures | GO to Pinpoint Test B |
| ABS | C0034:29 | Right Front Wheel Speed Sensor: Signal Invalid | GO to Pinpoint Test B |
| ABS | C0034:2F | Right Front Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test B |
| ABS | C0034:4A | Right Front Wheel Speed Sensor: Incorrect Component Installed | GO to Pinpoint Test O |
| ABS | C0034:64 | Right Front Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test B |
| ABS | C0036:07 | Left Rear Tone Wheel: Mechanical Failures | GO to Pinpoint Test AI |
| ABS | C0037:01 | Left Rear Wheel Speed Sensor: General Electrical Failure | GO to Pinpoint Test H |
| ABS | C0037:07 | Left Rear Wheel Speed Sensor: Mechanical Failures | GO to Pinpoint Test B |
| ABS | C0037:29 | Left Rear Wheel Speed Sensor: Signal Invalid | GO to Pinpoint Test B |
| ABS | C0037:2F | Left Rear Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test B |
| ABS | C0037:4A | Left Rear Wheel Speed Sensor: Incorrect Component Installed | GO to Pinpoint Test O |
| ABS | C0037:64 | Left Rear Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test B |
| ABS | C0039:07 | Right Rear Tone Wheel: Mechanical Failures | GO to Pinpoint Test AI |
| ABS | C003A:01 | Right Rear Wheel Speed Sensor: General Electrical Failure | GO to Pinpoint Test H |
| ABS | C003A:07 | Right Rear Wheel Speed Sensor: Mechanical Failures | GO to Pinpoint Test B |
| ABS | C003A:29 | Right Rear Wheel Speed Sensor: Signal Invalid | GO to Pinpoint Test B |
| ABS | C003A:2F | Right Rear Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test B |
| ABS | C003A:4A | Right Rear Wheel Speed Sensor: Incorrect Component Installed | GO to Pinpoint Test O |
| ABS | C003A:64 | Right Rear Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test B |
| ABS | C0040:64 | Brake Pedal Switch "A": Signal Plausibility Failure | GO to Pinpoint Test AK |
| ABS | C0044:49 | Brake Pressure Sensor "A": Internal Electronic Failure | GO to Pinpoint Test BA |
| ABS | C0047:01 | Brake Booster Pressure Sensor: General Electrical Failure | GO to Pinpoint Test Y |
| ABS | C0047:1C | Brake Booster Pressure Sensor: Circuit Voltage Out Of Range | GO to Pinpoint Test Y |
| ABS | C0047:62 | Brake Booster Pressure Sensor: Signal Compare Failure | GO to Pinpoint Test Y |
| ABS | C0047:64 | Brake Booster Pressure Sensor: Signal Plausibility Failure | GO to Pinpoint Test Y |
| ABS | C004A:13 | Brake Lining Wear Sensor: Circuit Open | GO to Pinpoint Test AW |
| ABS | C0061:28 | Lateral Acceleration Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test S |
| ABS | C0061:64 | Lateral Acceleration Sensor: Signal Plausibility Failure | GO to Pinpoint Test S |
| ABS | C0062:28 | Longitudinal Acceleration Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test S |
| ABS | C0062:54 | Longitudinal Acceleration Sensor: Missing Calibration | GO to Pinpoint Test P |
| ABS | C0062:64 | Longitudinal Acceleration Sensor: Signal Plausibility Failure | GO to Pinpoint Test S |
| ABS | C0063:28 | Yaw Rate Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test S |
| ABS | C0063:64 | Yaw Rate Sensor: Signal Plausibility Failure | GO to Pinpoint Test S |
| ABS | C0064:28 | Roll Rate Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test S |
| ABS | C0064:64 | Roll Rate Sensor: Signal Plausibility Failure | GO to Pinpoint Test S |
| ABS | C006B:00 | Stability System Active Too Long: No Sub Type Information | GO to Pinpoint Test BG |
| ABS | C0072:4B | Brake Temperature Too High: Over Temperature | GO to Pinpoint Test AO |
| ABS | C052B:93 | ABS Pump Motor Control Range/Performance: No Operation | GO to Pinpoint Test K |
| ABS | C052B:93 | ABS Pump Motor Control Range/Performance: No Operation | GO to Pinpoint Test AX |
| ABS | C052F:11 | ABS Pump Motor Supply Voltage "A" Circuit/Open: Circuit Short To Ground | GO to Pinpoint Test AX |
| ABS | C054E:01 | Vacuum Sensor "B" Range/Performance: General Electrical Failure | GO to Pinpoint Test AZ |
| ABS | C054E:1C | Vacuum Sensor "B" Range/Performance: Circuit Voltage Out Of Range | GO to Pinpoint Test AZ |
| ABS | C054E:64 | Vacuum Sensor "B" Range/Performance: Signal Plausibility Failure | GO to Pinpoint Test AZ |
| ABS | C101F:49 | Generic Valve Failure: Internal Electronic Failure | GO to Pinpoint Test K |
| ABS | C101F:49 | Generic Valve Failure: Internal Electronic Failure | GO to Pinpoint Test AG |
| ABS | C1020:00 | Brake System Fill Not Complete: No Sub Type Information | GO to Pinpoint Test F |
| ABS | C1105:29 | Brake Lamp Control: Signal Invalid | GO to Pinpoint Test BB |
| ABS | C1109:24 | Vehicle Dynamics Control Switch: Signal Stuck High | GO to Pinpoint Test BI |
| ABS | C1A90:16 | Wheel Speed Sensor Supply: Circuit Voltage Below Threshold | GO to Pinpoint Test G |
| ABS | C1A95:01 | Wheel Speed Sensor: General Electrical Failure | GO to Pinpoint Test G |
| ABS | C1A95:2F | Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test B |
| ABS | C1A95:4A | Wheel Speed Sensor: Incorrect Component Installed | GO to Pinpoint Test O |
| ABS | C1A99:28 | Pressure Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test AL |
| ABS | P050F:00 | Brake Assist Vacuum Too Low: No Sub Type Information | GO to Pinpoint Test AY |
| ABS | P050F:64 | Brake Assist Vacuum Too Low: Signal Plausibility Failure | GO to Pinpoint Test AY |
| ABS | P05D3:57 | Driver Mode Select Switch "A" Range/Performance: Invalid/Incompatible Software Component | GO to Pinpoint Test BD |
| ABS | P0604:94 | Internal Control Module Random Access Memory (RAM) Error: Unexpected Operation | GO to Pinpoint Test J |
| ABS | P062F:46 | Internal Control Module EEPROM Error: Calibration/Parameter Memory Failure | GO to Pinpoint Test J |
| ABS | P1708:64 | Clutch Switch Circuit: Signal Plausibility Failure | GO to Pinpoint Test BC |
| ABS | P258B:67 | Vacuum Pump Control Circuit "A" Range/Performance: Signal Incorrect After Event | GO to Pinpoint Test AM |
| ABS | U0001:16 | High Speed CAN Communication Bus: Circuit Voltage Below Threshold | GO to Pinpoint Test A |
| ABS | U0001:17 | High Speed CAN Communication Bus: Circuit Voltage Above Threshold | GO to Pinpoint Test D |
| ABS | U0001:88 | High Speed CAN Communication Bus: Bus Off | GO to Pinpoint Test D |
| ABS | U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test N |
| ABS | U0101:00 | Lost Communication with TCM: No Sub Type Information | GO to Pinpoint Test N |
| ABS | U0102:00 | Lost Communication with Transfer Case Control Module: No Sub Type Information | GO to Pinpoint Test AV |
| ABS | U0103:00 | Lost Communication With Gear Shift Control Module A: No Sub Type Information | GO to Pinpoint Test R |
| ABS | U0122:00 | Lost Communication With Vehicle Dynamics Control Module: No Sub Type Information | GO to Pinpoint Test T |
| ABS | U0131:00 | Lost Communication With Power Steering Control Module "A": No Sub Type Information | GO to Pinpoint Test L |
| ABS | U0131:86 | Lost Communication With Power Steering Control Module "A": Signal Invalid | GO to Pinpoint Test L |
| ABS | U0131:87 | Lost Communication With Power Steering Control Module "A": Missing Message | GO to Pinpoint Test L |
| ABS | U0137:00 | Lost Communication With Trailer Brake Control Module: No Sub Type Information | GO to Pinpoint Test AN |
| ABS | U0138:00 | Lost Communication with All Terrain Control Module: No Sub Type Information | GO to Pinpoint Test AS |
| ABS | U0138:86 | Lost Communication with All Terrain Control Module: Signal Invalid | GO to Pinpoint Test AS |
| ABS | U0138:87 | Lost Communication with All Terrain Control Module: Missing Message | GO to Pinpoint Test AS |
| ABS | U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test C |
| ABS | U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test S |
| ABS | U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test Q |
| ABS | U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test AB |
| ABS | U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | GO to Pinpoint Test V |
| ABS | U0164:87 | Lost Communication With HVAC Control Module: Missing Message | GO to Pinpoint Test V |
| ABS | U0232:00 | Lost Communication With Side Obstacle Detection Control Module "A": No Sub Type Information | GO to Pinpoint Test Z |
| ABS | U0233:00 | Lost Communication With Side Obstacle Detection Control Module "B": No Sub Type Information | GO to Pinpoint Test AA |
| ABS | U023A:00 | Lost Communication With Image Processing Module A: No Sub Type Information | GO to Pinpoint Test U |
| ABS | U023B:00 | Lost Communication With Image Processing Module B: No Sub Type Information | GO to Pinpoint Test W |
| ABS | U0243:00 | Lost Communication With Parking Assist Control Module "B": No Sub Type Information | GO to Pinpoint Test AP |
| ABS | U024E:00 | Lost Communication With Side Obstacle Detection Control Module "C": No Sub Type Information | GO to Pinpoint Test AQ |
| ABS | U024F:00 | Lost Communication With Side Obstacle Detection Control Module "D": No Sub Type Information | GO to Pinpoint Test AR |
| ABS | U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test X |
| ABS | U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test AE |
| ABS | U0401:82 | Invalid Data Received from ECM/PCM A: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test N |
| ABS | U0401:83 | Invalid Data Received from ECM/PCM A: Value Of Signal Protection Calculation Incorrect | GO to Pinpoint Test N |
| ABS | U0401:86 | Invalid Data Received from ECM/PCM A: Signal Invalid | GO to Pinpoint Test N |
| ABS | U0402:00 | Invalid Data Received from TCM: No Sub Type Information | GO to Pinpoint Test N |
| ABS | U0403:00 | Invalid Data Received From Transfer Case Control Module: No Sub Type Information | GO to Pinpoint Test AV |
| ABS | U0404:86 | Invalid Data Received from Gear Shift Control Module A: Signal Invalid | GO to Pinpoint Test R |
| ABS | U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test C |
| ABS | U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test D |
| ABS | U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | GO to Pinpoint Test Q |
| ABS | U0424:00 | Invalid Data Received From HVAC Control Module: No Sub Type Information | GO to Pinpoint Test V |
| ABS | U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AC |
| ABS | U0452:41 | Invalid Data Received From Restraints Control Module: General Checksum Failure | GO to Pinpoint Test AU |
| ABS | U0452:86 | Invalid Data Received From Restraints Control Module: Signal Invalid | GO to Pinpoint Test AC |
| ABS | U053B:41 | Invalid Data Received From Image Processing Module A: General Checksum Failure | GO to Pinpoint Test AT |
| ABS | U053B:82 | Invalid Data Received From Image Processing Module A: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AT |
| ABS | U053B:83 | Invalid Data Received From Image Processing Module A: Value Of Signal Protection Calculation Incorrect | GO to Pinpoint Test AT |
| ABS | U0554:86 | Invalid Data Received From Accessory Protocol Interface Module: Signal Invalid | GO to Pinpoint Test X |
| ABS | U1A36:56 | Module Code: Invalid/Incompatible Configuration | GO to Pinpoint Test K |
| ABS | U2001:00 | Reduced System Function: No Sub Type Information | GO to Pinpoint Test BE |
| ABS | U2017:93 | Control Module Software #2: No Operation | GO to Pinpoint Test K |
| ABS | U2017:93 | Control Module Software #2: No Operation | GO to Pinpoint Test BF |
| ABS | U2100:46 | Initial Configuration Not Complete: Calibration/Parameter Memory Failure | GO to Pinpoint Test K |
| ABS | U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test K |
| ABS | U2101:46 | Control Module Configuration Incompatible: Calibration/Parameter Memory Failure | GO to Pinpoint Test K |
| ABS | U2101:56 | Control Module Configuration Incompatible: Invalid/Incompatible Configuration | GO to Pinpoint Test K |
| ABS | U2107:00 | Collision Mitigation By Braking: No Sub Type Information | GO to Pinpoint Test I |
| ABS | U2107:68 | Collision Mitigation By Braking: Event Information | GO to Pinpoint Test AT |
| ABS | U2108:68 | Adaptive Cruise Control: Event Information | GO to Pinpoint Test AT |
| ABS | U2200:41 | Control Module Configuration Memory Corrupt: General Checksum Failure | GO to Pinpoint Test J |
| ABS | U3000:00 | Control Module: No Sub Type Information | GO to Pinpoint Test J |
| ABS | U3000:04 | Control Module: System Internal Failures | GO to Pinpoint Test J |
| ABS | U3000:19 | Control Module: Circuit Current Above Threshold | GO to Pinpoint Test J |
| ABS | U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test J |
| ABS | U3000:44 | Control Module: Data Memory Failure | GO to Pinpoint Test J |
| ABS | U3000:46 | Control Module: Calibration/Parameter Memory Failure | GO to Pinpoint Test J |
| ABS | U3000:47 | Control Module: Watchdog/Safety μC Failure | GO to Pinpoint Test J |
| ABS | U3000:48 | Control Module: Supervision Software Failure | GO to Pinpoint Test J |
| ABS | U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test J |
| ABS | U3000:4B | Control Module: Over Temperature | GO to Pinpoint Test J |
| ABS | U3002:62 | Vehicle Identification Number: Signal Compare Failure | GO to Pinpoint Test M |
| ABS | U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test A |
| ABS | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test D |