Transmission, Oil Temperature Sensor - Removal & Installation
- Transmission, Removing
- Notes
- Preparatory Work
- Removal
- Measuring the Position Of the Tie Rod In the Steering Gear
- Removing the Lower Steering Shaft Joint
- Removing Engine Compartment Components
- Removing the Torque Rod
- Removing the Gear Selector Cable And Lever On the Transmission
- Removing the Hose For the Heater Pipe
- Collecting Transmission Fluid
- Removing the Dipstick
- Removing the Starter Motor
- Removing the Screws For the Transmission And Starter Motor And the Ground Lead
- Removing the Screws From the Torque Converter
- Installing the Lifting Fixture
- Installing the Lifting Beam And Lifting Hook On the Engine Lifting Eyelet
- Disconnecting the Front Suspension Components
- Removing the Protective Plate
- Removing the Screws For the Cable Conduit And Ground Lead Bracket On the Sub-Frame
- Removing Components
- Removing the Servo Line And the Evaporator Line
- Removing the SIPS Member
- Removing the Rubber Mountings For the Exhaust Pipe
- Removing the Heated Oxygen Sensors (HO2S) Connector
- Removing the Screw For the Rear Engine Mounting
- Removing the Screws For the Right-Hand Engine Pad
- Lowering the Sub-Frame With the Steering Gear
- Removing the Drive Shafts From the Wheel Spindles
- Removing the Left Drive Shaft From the Gearbox
- Removing the Drive Shaft
- Pay Attention To the Following When Removing Propeller Shaft
- Removing the Propeller Shaft
- Removing the Engine Mounting Together With the Bracket And the Splash Guard
- Removing the Oil Pipe From the Gearbox
- Lowering the Engine And Transmission
- Removing the Heated Oxygen Sensor (HO2S) Connectors From the Bracket On the Transmission
- Preparations For Removal Of the Transmission
- Installing the Fixture On the Mobile Jack
- Aligning the Fixture On the Transmission
- Removing the Chain Housing Bracket
- Removing the Bevel Gear/Chain Housing
- Checking the Sealing Ring
- Removing the Gearbox
- Flushing the Oil Cooler And Oil Hoses
- Upper Torque Rod
- Wheel Knuckle/Spring Strut, Calibrating
- Wire Harness, Control System, Replacing
- Preparations
- Remove the Air Cleaner (ACL) Housing
- Check the Cable Harness
- Remove the Transmission Cable From the Bracket And From the Lever On the Transmission
- Remove the Cable Harness Retainer
- Separate the Connector
- Remove the Socket And the Cable Harness
- Install the Cable Harness
- Install the Cable Harness Retainer
- Assemble the Connector
- Connect the Connector To the Transmission
- Install the Transmission Cable On the Transmission
- Assembling the Control System
- Installing the Sub-Frame And Front Suspension Components
- Wiring Harness/Oil Temperature Sensor, Replacing
- Notes
- Removal
- Preparations
- Remove the Transmission Cable From the Lever On the Transmission
- Disassembling the Large Connector
- Removing the Lever On the Gear Shift Linkage Rod
- Installing the Lifting Beam And Lifting Hook
- Lifting the Car
- Removing the Screw For the Right Drive Shaft
- Removing the Screws For the Cable Conduit And Ground Lead Bracket On the Sub-Frame
- Removing the Ball Joint Nuts (Both Sides)
- Removing the Bracket For the Cable For the Heated Oxygen Sensor (HO2S)
- Removing the Collision Protection System Over the Steering Gear (Right-Hand Drive Cars Only)
- Removing the Steering Gear From the Sub-Frame
- Removing the Screws From the Sub-Frame Support Brackets (Both Sides)
- Lowering the sub-frame
- Draining the Transmission Fluid
- Removing the Control System Cover
- Removing the Cable Harness
- Assembling the Control System
- Installing the Sub-Frame And Front Suspension Components
- Installing the Sub-Frame
- Installing Components In the Steering Gear And Sub-Frame
- Installing the Nuts Securing the Ball Joint To the Control Arm And the Anti-Roll Bar To the Link Rods
- Installing the Collision Protection System Over the Steering Gear (Right-Hand Drive Cars)
- Installing the Bracket For the Heated Oxygen Sensor (HO2S)
- Installing the Screw For the Drive Shaft
- Installing Components On the Sub-Frame
- Installing the Splash Guard Under the Engine
- Removing Lifting Beams And the Lifting Hook
- Assembling the Connectors
- Installing Connectors And Wiring
- Installing the Air Cleaner (ACL) Housing And Connections