Chassis Electrical
- Battery
- Ignition Switch
- General Description
- Ignition Key Reminder Tone Alarm And Door Lock Prevention Function Diagnosis
- Immobilizer System Diagnosis
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- Symptom Chart
- Symptom Procedures
- Data List Reference Table
- Check At Immobilizer-Ecu
- Special Tools
- On-Vehicle Service
- Ignition Switch
- Combination Meter Assembly
- General Description
- Combination Meters Diagnosis
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC U1073: Bus Off
- DTC U1100: Powertrain Control Module Time-out (Related to Engine) Or DTC U1101: Powertrain Control Module Time-out (Related to A/T)
- DTC U1102: ABS-ECU Time-out
- DTC U1109: ETACS-ECU Time-out
- DTC U1112: SRS-ECU Time-out
- DTC U1120: Failure Information on Powertrain Control Module (Related to Engine)
- DTC U1206: Flag invalid
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: Communication With Scan Tool is Not Possible.
- INSPECTION PROCEDURE 2: Power Supply Circuit. INSPECTION PROCEDURE 3: Odometer and trip meter are not displayed. INSPECTION PROCEDURE 4: All the needle meters do not work. INSPECTION PROCEDURE 5: When the ignition switch is turned to the ON position, the indicator and warning lights do not illuminate.
- INSPECTION PROCEDURE 6: Speedometer does not Work. INSPECTION PROCEDURE 7: The Fuel Gauge Needle Moves Excessively.
- INSPECTION PROCEDURE 8: Tachometer does not Work.
- INSPECTION PROCEDURE 9: Fuel Gauge does not work (other meters work).
- INSPECTION PROCEDURE 10: Engine Coolant Temperature Gauge does not Work (other meters work).
- Combination Meter Terminal Check
- Special Tools
- On-Vehicle Service
- Combination Meter Assembly
- Headlight, Front Side Marker Light And Position Light Assembly
- Fog Light
- Rear Combination Light
- Dome Light
- License Plate Light
- High-Mounted Stoplight
- Rheostat
- Hazard Warning Light Switch
- Column Switch
- Horn
- Accessory Socket
- Radio With Cd Player
- General Description
- Radio With Cd Player, Speaker And Antenna Diagnosis
- Trouble Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: When Power Switch is Turned "ON," no Power is Available.
- INSPECTION PROCEDURE 2: When Remote Controlled Radio Power Switch is Turned "ON," no Power is Available. But Radio, CD Player and CD Changer Power Switch is Available.
- INSPECTION PROCEDURE 3: The system does not recognize the remote controlled radio switch (RH) only.
- INSPECTION PROCEDURE 4: The system does not recognize the remote controlled radio switch (LH) only.
- INSPECTION PROCEDURE 5: No Sound.
- INSPECTION PROCEDURE 6: No Sound from One Speaker.
- INSPECTION PROCEDURE 7: No Sound from One Speaker.
- INSPECTION PROCEDURE 8: Noise is Present while Moving (AM).
- INSPECTION PROCEDURE 9: Noise is Present while Moving (FM).
- INSPECTION PROCEDURE 10: Sound mixed with Noise, Only at Night (AM).
- INSPECTION PROCEDURE 11: Noise is Overpowering both AM and FM.
- INSPECTION PROCEDURE 12: Excessive Noise on AM and FM.
- INSPECTION PROCEDURE 13: Noise is Detected with Engine Running.
- INSPECTION PROCEDURE 14: Noise Appears During Vibration or Shocks.
- INSPECTION PROCEDURE 15: Noise is Present While Moving (FM).
- INSPECTION PROCEDURE 16: Constant Noise.
- INSPECTION PROCEDURE 17: No reception (AM).
- INSPECTION PROCEDURE 18: Poor Reception.
- INSPECTION PROCEDURE 19: Distortion on AM and/or FM.
- INSPECTION PROCEDURE 20: Distortion on FM Only.
- INSPECTION PROCEDURE 21: Auto Select Function Inoperative, too Few Automatic Stations are Selected.
- INSPECTION PROCEDURE 22: Preset Stations are Erased.
- INSPECTION PROCEDURE 23: CD can not be Inserted.
- INSPECTION PROCEDURE 24: No Sound (CD Only).
- INSPECTION PROCEDURE 25: CD Sound Skips.
- INSPECTION PROCEDURE 26: Sound Quality is Poor.
- INSPECTION PROCEDURE 27: CD cannot be Ejected.
- On-Vehicle Service
- Special Tool
- Radio With Cd Player
- Remote Controlled Radio Switch
- Speaker
- Amplifier
- Antenna
- Defogger
- Multi-Center Display
- General Description
- Diagnosis Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC 010: Bus Off
- DTC 011: Powertrain Control Module Time-out (Related to Engine) DTC 012: Powertrain Control Module Time-out (Related to A/T)
- DTC 013: A/C-ECU Time-out
- DTC 014: Combination Meter Time-out
- DTC 019: ETACS-ECU Time-out
- DTC 020: Failures Information on Powertrain Control Module (Related to Engine)
- DTC 021: Failures Information on Combination Meter
- DTC 022: Failures Information on A/C-ECU
- Diagnosis
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: Communication With Scan Tool Is Not Possible. (Middle Grade Type)
- INSPECTION PROCEDURE 2: The multi-center display does not Show any Information. (Middle Grade type): INSPECTION PROCEDURE 3: The multi-center display does not Show any Information. (Low Grade type)
- INSPECTION PROCEDURE 4: The A/C Display Shows "COMMUNICATION ERROR", and then can not Proceed to Next Screen. (Middle Grade Type)
- INSPECTION PROCEDURE 5: The Ambient Air Temperature Display Shows "COM ERROR" or "-°C (-°F)." (Middle Grade Type)
- INSPECTION PROCEDURE 6: On the Audio Screen, "COMMUNICATION ERROR" cannot Proceed to Next Screen. (Middle Grade Type)
- INSPECTION PROCEDURE 7: The Compass can not be Calibrated Manually, or Becomes Out of Calibration Easily (Middle Grade Type)
- On-Vehicle Service
- Check At Multi Center Display Unit Terminal
- Special Tools
- Multi-Center Display
- Ambient Temperature Sensor
- Panic Alarm
- Specifications