Diagnostic Trouble Code (DTC) Chart
WARNING: This page is about a different car, the 2022 Ford Police Interceptor Utility and 2022 Ford Explorer. However, it is still accessible from the selected car via links, so may be relevant.
Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| Module | DTC | Description | Action |
|---|---|---|---|
| ABS | C0020:11 | ABS Pump Motor Control: Circuit Short To Ground | GO to Pinpoint Test H |
| ABS | C0020:12 | ABS Pump Motor Control: Circuit Short To Battery | GO to Pinpoint Test H |
| ABS | C0020:13 | ABS Pump Motor Control: Circuit Open | GO to Pinpoint Test H |
| ABS | C0020:49 | ABS Pump Motor Control: Internal Electronic Failure | GO to Pinpoint Test H |
| ABS | C0020:71 | ABS Pump Motor Control: Actuator Stuck | GO to Pinpoint Test H |
| ABS | C0030:07 | Left Front Tone Wheel: Mechanical Failures | GO to Pinpoint Test AB |
| ABS | C0031:01 | Left Front Wheel Speed Sensor: General Electrical Failure | GO to Pinpoint Test M |
| ABS | C0031:07 | Left Front Wheel Speed Sensor: Mechanical Failures | GO to Pinpoint Test AB |
| ABS | C0031:2F | Left Front Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test AB |
| ABS | C0031:4A | Left Front Wheel Speed Sensor: Incorrect Component Installed | GO to Pinpoint Test AL |
| ABS | C0031:64 | Left Front Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test AB |
| ABS | C0033:07 | Right Front Tone Wheel: Mechanical Failures | GO to Pinpoint Test AB |
| ABS | C0034:01 | Right Front Wheel Speed Sensor: General Electrical Failure | GO to Pinpoint Test M |
| ABS | C0034:07 | Right Front Wheel Speed Sensor: Mechanical Failures | GO to Pinpoint Test AB |
| ABS | C0034:2F | Right Front Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test AB |
| ABS | C0034:4A | Right Front Wheel Speed Sensor: Incorrect Component Installed | GO to Pinpoint Test AL |
| ABS | C0034:64 | Right Front Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test AB |
| ABS | C0036:07 | Left Rear Tone Wheel: Mechanical Failures | GO to Pinpoint Test AB |
| ABS | C0037:01 | Left Rear Wheel Speed Sensor: General Electrical Failure | GO to Pinpoint Test N |
| ABS | C0037:07 | Left Rear Wheel Speed Sensor: Mechanical Failures | GO to Pinpoint Test AB |
| ABS | C0037:2F | Left Rear Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test AB |
| ABS | C0037:4A | Left Rear Wheel Speed Sensor: Incorrect Component Installed | GO to Pinpoint Test AL |
| ABS | C0037:64 | Left Rear Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test AB |
| ABS | C0039:07 | Right Rear Tone Wheel: Mechanical Failures | GO to Pinpoint Test AB |
| ABS | C003A:01 | Right Rear Wheel Speed Sensor: General Electrical Failure | GO to Pinpoint Test N |
| ABS | C003A:07 | Right Rear Wheel Speed Sensor: Mechanical Failures | GO to Pinpoint Test AB |
| ABS | C003A:2F | Right Rear Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test AB |
| ABS | C003A:4A | Right Rear Wheel Speed Sensor: Incorrect Component Installed | GO to Pinpoint Test AL |
| ABS | C003A:64 | Right Rear Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test AB |
| ABS | C0040:64 | Brake Pedal Switch "A": Signal Plausibility Failure | GO to Pinpoint Test AC |
| ABS | C0044:49 | Brake Pressure Sensor "A": Internal Electronic Failure | GO to Pinpoint Test AM |
| ABS | C0044:51 | Brake Pressure Sensor "A": Not Programmed | GO to Pinpoint Test AM |
| ABS | C0044:64 | Brake Pressure Sensor "A": Signal Plausibility Failure | GO to Pinpoint Test AM |
| ABS | C0044:8F | Brake Pressure Sensor "A": Erratic | GO to Pinpoint Test AM |
| ABS | C0047:1C | Brake Booster Pressure Sensor: Circuit Voltage Out Of Range | GO to Pinpoint Test CO |
| ABS | C0047:64 | Brake Booster Pressure Sensor: Signal Plausibility Failure | GO to Pinpoint Test CO |
| ABS | C0049:01 | Brake Fluid Level: General Electrical Failure | GO to Pinpoint Test I |
| ABS | C0049:7A | Brake Fluid Level: Fluid Leak Or Seal Failure | GO to Pinpoint Test K |
| ABS | C0049:7B | Brake Fluid Level: Low Fluid Level | GO to Pinpoint Test I |
| ABS | C0051:64 | Steering Wheel Position Sensor: Signal Plausibility Failure | GO to Pinpoint Test LA |
| ABS | C0051:67 | Steering Wheel Position Sensor: Signal Incorrect After Event | GO to Pinpoint Test LA |
| ABS | C0051:85 | Steering Wheel Position Sensor: Signal Above Allowable Range | GO to Pinpoint Test LA |
| ABS | C0051:86 | Steering Wheel Position Sensor: Signal Invalid | GO to Pinpoint Test LA |
| ABS | C0061:28 | Lateral Acceleration Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test AG |
| ABS | C0061:64 | Lateral Acceleration Sensor: Signal Plausibility Failure | GO to Pinpoint Test AG |
| ABS | C0062:54 | Longitudinal Acceleration Sensor: Missing Calibration | GO to Pinpoint Test AN |
| ABS | C0062:64 | Longitudinal Acceleration Sensor: Signal Plausibility Failure | GO to Pinpoint Test AG |
| ABS | C0063:28 | Yaw Rate Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test AG |
| ABS | C0063:64 | Yaw Rate Sensor: Signal Plausibility Failure | GO to Pinpoint Test AG |
| ABS | C0064:28 | Roll Rate Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test AG |
| ABS | C0064:64 | Roll Rate Sensor: Signal Plausibility Failure | GO to Pinpoint Test AG |
| ABS | C0078:56 | Tire Diameter: Invalid/Incompatible Configuration | GO to Pinpoint Test ZA |
| ABS | C052E:A2 | ABS Pump Motor Control Circuit Low: System Voltage Low | GO to Pinpoint Test H |
| ABS | C0594:12 | Brake Booster Motor "A" Performance: Circuit Short To Battery | GO to Pinpoint Test CP |
| ABS | C0594:78 | Brake Booster Motor "A" Performance: Alignment Or Adjustment Incorrect | GO to Pinpoint Test CP |
| ABS | C0594:92 | Brake Booster Motor "A" Performance: Performance Or Incorrect Operation | GO to Pinpoint Test CP |
| ABS | C0596:00 | Brake Booster Motor "A" Current Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test CP |
| ABS | C1013:09 | Brake System Pressure: Component Failures | GO to Pinpoint Test CO |
| ABS | C1013:7A | Brake System Pressure: Fluid Leak Or Seal Failure | GO to Pinpoint Test CO |
| ABS | C1013:7C | Brake System Pressure: Slow Response | GO to Pinpoint Test CO |
| ABS | C1013:92 | Brake System Pressure: Performance Or Incorrect Operation | GO to Pinpoint Test CO |
| ABS | C1018:61 | Regenerative Braking: Signal Calculation Failure | GO to Pinpoint Test Z |
| ABS | C1019:29 | Linear Actuator Control (LAC): Signal Invalid | GO to Pinpoint Test CO |
| ABS | C1019:74 | Linear Actuator Control (LAC): Actuator Slipping | GO to Pinpoint Test CO |
| ABS | C1019:78 | Linear Actuator Control (LAC): Alignment Or Adjustment Incorrect | GO to Pinpoint Test CO |
| ABS | C1019:92 | Linear Actuator Control (LAC): Performance Or Incorrect Operation | GO to Pinpoint Test CO |
| ABS | C101F:46 | Generic Valve Failure: Calibration/Parameter Memory Failure | GO to Pinpoint Test Z |
| ABS | C101F:49 | Generic Valve Failure: Internal Electronic Failure | GO to Pinpoint Test Z |
| ABS | C1020:00 | Brake System Fill Not Complete: No Sub Type Information | GO to Pinpoint Test C |
| ABS | C1109:64 | Vehicle Dynamics Control Switch: Signal Plausibility Failure | GO to Pinpoint Test O |
| ABS | C1137:00 | Reverse gear switch: No Sub Type Information | GO to Pinpoint Test J |
| ABS | P0562:16 | System Voltage Low: Circuit Voltage Below Threshold | GO to Pinpoint Test A |
| ABS | P0563:17 | System Voltage High: Circuit Voltage Above Threshold | GO to Pinpoint Test F |
| ABS | P1177:64 | Synchronization: Signal Plausibility Failure | GO to Pinpoint Test Y |
| ABS | U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test AI |
| ABS | U0100:82 | Lost Communication With ECM/PCM "A": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AI |
| ABS | U0100:83 | Lost Communication With ECM/PCM "A": Value Of Signal Protection Calculation Incorrect | GO to Pinpoint Test AI |
| ABS | U0100:87 | Lost Communication With ECM/PCM "A": Missing Message | GO to Pinpoint Test AI |
| ABS | U0102:00 | Lost Communication with Transfer Case Control Module: No Sub Type Information | GO to Pinpoint Test AU |
| ABS | U0103:00 | Lost Communication With Gear Shift Control Module A: No Sub Type Information | GO to Pinpoint Test AV |
| ABS | U011D:87 | Lost Communication With All Wheel Drive Control Module: Missing Message | GO to Pinpoint Test BX |
| ABS | U0122:00 | Lost Communication With Vehicle Dynamics Control Module: No Sub Type Information | GO to Pinpoint Test BR |
| ABS | U0131:82 | Lost Communication With Power Steering Control Module "A": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AE |
| ABS | U0131:83 | Lost Communication With Power Steering Control Module "A": Value Of Signal Protection Calculation Incorrect | GO to Pinpoint Test AE |
| ABS | U0131:87 | Lost Communication With Power Steering Control Module "A": Missing Message | GO to Pinpoint Test AE |
| ABS | U0138:00 | Lost Communication with All Terrain Control Module: No Sub Type Information | GO to Pinpoint Test BM |
| ABS | U0138:86 | Lost Communication with All Terrain Control Module: Signal Invalid | GO to Pinpoint Test BM |
| ABS | U0138:87 | Lost Communication with All Terrain Control Module: Missing Message | GO to Pinpoint Test BM |
| ABS | U0140:87 | Lost Communication With Body Control Module: Missing Message | GO to Pinpoint Test D |
| ABS | U0146:00 | Lost Communication With Serial Data Gateway "A": No Sub Type Information | GO to Pinpoint Test BP |
| ABS | U0146:87 | Lost Communication With Serial Data Gateway "A": Missing Message | GO to Pinpoint Test BP |
| ABS | U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BH |
| ABS | U0151:82 | Lost Communication With Restraints Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BH |
| ABS | U0151:83 | Lost Communication With Restraints Control Module: Value Of Signal Protection Calculation Incorrect | GO to Pinpoint Test BH |
| ABS | U0151:87 | Lost Communication With Restraints Control Module: Missing Message | GO to Pinpoint Test BH |
| ABS | U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AR |
| ABS | U0155:87 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: Missing Message | GO to Pinpoint Test AR |
| ABS | U0159:87 | Lost Communication With Parking Assist Control Module "A": Missing Message | GO to Pinpoint Test BY |
| ABS | U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | GO to Pinpoint Test CE |
| ABS | U0164:87 | Lost Communication With HVAC Control Module: Missing Message | GO to Pinpoint Test CE |
| ABS | U0212:86 | Lost Communication With Steering Column Control Module: Signal Invalid | GO to Pinpoint Test BV |
| ABS | U0212:87 | Lost Communication With Steering Column Control Module: Missing Message | GO to Pinpoint Test BV |
| ABS | U0232:87 | Lost Communication With Side Obstacle Detection Control Module "A": Missing Message | GO to Pinpoint Test BZ |
| ABS | U0233:87 | Lost Communication With Side Obstacle Detection Control Module "B": Missing Message | GO to Pinpoint Test BZ |
| ABS | U023A:87 | Lost Communication With Image Processing Module A: Missing Message | GO to Pinpoint Test BQ |
| ABS | U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test CL |
| ABS | U0293:00 | Lost Communication With Hybrid/EV Powertrain Control Module "A": No Sub Type Information | GO to Pinpoint Test CM |
| ABS | U0300:51 | Internal Control Module Software Incompatibility: Not Programmed | GO to Pinpoint Test Z |
| ABS | U0401:81 | Invalid Data Received from ECM/PCM A: Invalid Serial Data Received | GO to Pinpoint Test AI |
| ABS | U0401:82 | Invalid Data Received from ECM/PCM A: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AI |
| ABS | U0401:83 | Invalid Data Received from ECM/PCM A: Value Of Signal Protection Calculation Incorrect | GO to Pinpoint Test AI |
| ABS | U0401:86 | Invalid Data Received from ECM/PCM A: Signal Invalid | GO to Pinpoint Test AI |
| ABS | U0402:00 | Invalid Data Received from TCM: No Sub Type Information | GO to Pinpoint Test AI |
| ABS | U0404:86 | Invalid Data Received from Gear Shift Control Module A: Signal Invalid | GO to Pinpoint Test AV |
| ABS | U0422:86 | Invalid Data Received From Body Control Module: Signal Invalid | GO to Pinpoint Test D |
| ABS | U0424:86 | Invalid Data Received From HVAC Control Module: Signal Invalid | GO to Pinpoint Test CE |
| ABS | U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BH |
| ABS | U0452:86 | Invalid Data Received From Restraints Control Module: Signal Invalid | GO to Pinpoint Test BH |
| ABS | U053B:82 | Invalid Data Received From Image Processing Module A: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BQ |
| ABS | U053B:83 | Invalid Data Received From Image Processing Module A: Value Of Signal Protection Calculation Incorrect | GO to Pinpoint Test BQ |
| ABS | U053B:86 | Invalid Data Received From Image Processing Module A: Signal Invalid | GO to Pinpoint Test BQ |
| ABS | U0554:86 | Invalid Data Received From Accessory Protocol Interface Module: Signal Invalid | GO to Pinpoint Test CL |
| ABS | U0594:86 | Invalid Data Received From Hybrid/EV Powertrain Control Module "A": Signal Invalid | GO to Pinpoint Test CM |
| ABS | U2001:00 | Reduced System Function: No Sub Type Information | GO to Pinpoint Test B |
| ABS | U2017:57 | Control Module Software #2: Invalid/Incompatible Software Component | GO to Pinpoint Test Z |
| ABS | U2017:93 | Control Module Software #2: No Operation | GO to Pinpoint Test Z |
| ABS | U2018:57 | Control Module Software #3: Invalid/Incompatible Software Component | GO to Pinpoint Test Z |
| ABS | U2024:51 | Control Module Cal-Config Data: Not Programmed | GO to Pinpoint Test Z |
| ABS | U2024:57 | Control Module Cal-Config Data: Invalid/Incompatible Software Component | GO to Pinpoint Test Z |
| ABS | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test Z |
| ABS | U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test Z |
| ABS | U2107:00 | Collision Mitigation By Braking: No Sub Type Information | GO to Pinpoint Test R |
| ABS | U2107:68 | Collision Mitigation By Braking: Event Information | GO to Pinpoint Test AQ |
| ABS | U2108:68 | Adaptive Cruise Control: Event Information | GO to Pinpoint Test R |
| ABS | U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test Z |
| ABS | U3000:00 | Control Module: No Sub Type Information | GO to Pinpoint Test Y |
| ABS | U3000:04 | Control Module: System Internal Failures | GO to Pinpoint Test Y |
| ABS | U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test Y |
| ABS | U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test Y |
| ABS | U3000:4B | Control Module: Over Temperature | GO to Pinpoint Test Y |
| ABS | U3000:96 | Control Module: Component Internal Failure | GO to Pinpoint Test Y |
| ABS | U3001:68 | Control Module Improper Shutdown Performance: Event Information | GO to Pinpoint Test G |
| ABS | U3002:51 | Vehicle Identification Number: Not Programmed | GO to Pinpoint Test AF |
| ABS | U3002:62 | Vehicle Identification Number: Signal Compare Failure | GO to Pinpoint Test AF |
| ABS | U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test A |
| ABS | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test F |
| ABS | U300A:29 | Ignition Switch: Signal Invalid | GO to Pinpoint Test A |
| ABS | U3012:00 | Control Module Improper Wake-up Performance: No Sub Type Information | GO to Pinpoint Test E |
| ATCM | P05D3:86 | Driver Mode Select Switch "A" Range/Performance: Signal Invalid | GO to Pinpoint Test OB |
| PCM | P05FF:00 | Brake Pressure Sensor / Brake Pedal Position Sensor Correlation: No Sub Type Information | GO to Pinpoint Test CO |