Service Guidance
| Type/Chassis: | Location: |
| Factory complete date: | Retail delivery date: |
| Perform inspection in the order detailed below. Check and note the inspection result in the boxes below. | ||||||
| Legend: "OK / Not OK" = to be executed at interval / "-" = Not to be executed at interval. | ||||||
| Maintenance date from "Factory Complete": | ||||||
| Interval days: | 30 | 60 | 90 | 120 | 150 | 180 |
| 1) Battery charge 12 V | - | OK Charge |
OK Charge |
OK Charge |
OK Charge |
OK Charge |
| 2) PHEV vehicles: Check SOC / Charge high voltage battery | - | - | - | - | - | OK Charge |
| 3) Check Rapgard™ (brake protection) | - | - | OK Remove |
OK Remove |
OK Remove |
OK Remove |
| 4) Check exterior cleanliness | - | OK Wash |
OK Wash |
OK Wash |
OK Wash |
OK Wash |
| 5) Check tire pressure | - | OK Adjust |
OK Adjust |
OK Adjust |
OK Adjust |
OK Adjust |
| 6) Check interior components | - | - | OK Adjust |
- | OK Adjust |
- |
| 7) Check interior protections | - | - | OK Adjust |
- | OK Adjust |
- |
| 8) Remove Rapgard™ | - | - | - | - | - | - |
| 9) Change engine oil and filter | - | - | - | - | - | - |
| 10) Disc brake rust cleaning | - | - | OK | - | OK | - |
| 11) Remove vehicle cover | - | - | - | - | - | - |
| 12) Tape remove | - | - | - | - | - | OK |
| Inspector initials/Number: | ||||||
| Comments: | ||||||
| 1) Battery charge 12 V Vehicles of MY 2017- and in transport mode: - XC60 (18-) / XC90 / S90 / V90 / V60 (19-) / S60 (19-) / Polestar 1 / XC40: > Open the driver door. > Depress the hazard button 1-2 s and wait for DIM to start. > Look for "Battery charge needed" or "Battery charge OK" and charge if needed. - XC60 (-17) / V40 / V60 (-18) / S60 (-18): > Open the driver door. > Depress the brake pedal. > Wait for DIM to start. > If the battery symbol is ON, charge the battery. - Vehicles of MY -2016 and in transport mode: > Charge the battery. |
| 2) PHEV vehicles: Check SOC / Charge high voltage battery > Check the state of charge (SOC) for the high voltage battery in DIM. If the status is below 1 bar, charge to between 3 and 6 bars. |
| 3) Check Rapgard™ (brake protection) > If the brake protection is broken, remove it before transport. |
| 4) Check exterior cleanliness > Wash if necessary. > Check for damages and repair if necessary. |
| 5) Check tire pressure > Set the tire pressure to 330±20 kPa, 48±3 PSI. |
| 6) Check interior components > Check for heat related failures and cleanliness among the interior components. |
| 7) Check interior protections > Check the positions of the interior protections. > Correct the positions if required. |
| 8) Remove Rapgard™ (brake protection) > Ensure that the vehicle is washed if needed. |
| 9) Change engine oil and filter > Exchange the engine oil and replace the oil filter. > When finished, reset the service reminder indicator. |
| 10) Disc brake rust cleaning > Drive the vehicle 0.3 km / 0.2 miles at low speed. > Depress the brake pedal five times (5 s per application). |
| 11) Remove vehicle cover > If applicable, remove the vehicle cover. |
| 11) Tape remove > After 180 days, remove the tape from the inner front sill moulding at the driver side. |