Transmission Oil - Checking Oil Grade & Level
- Transmission
- Input shaft seal
- Input shaft, cleaning (gasoline M65 1999-)
- Input shaft, cleaning (B5244T5, M66; 2005-2008)
- Installing the gearbox (B5204T5, AW55-50/51SN; 2004-2007)
- Notes
- Installation
- Notes
- Installing the gearbox
- Installing and tightening the screws to the gearbox
- Fitting the torque converter screws.
- Lifting the engine/gearbox
- Installing the rear engine mounting
- Installing the angle gear
- Installing the lower oil pipe to the gearbox
- Installing the left-hand drive shaft to the gearbox and the wheel spindle
- Fitting the subframe to the body
- Installing the right-hand drive shaft to the gearbox, wheel spindle and link arm
- Tightening the subframe screws (both sides)
- Fitting the screws for engine pads and the torque rod bracket in the gearbox
- Installing the steering wheel shaft joint
- Installing the collision protection system over the steering gear
- Installing the crossmembers
- Installing and tightening the front suspension components
- Installing the cable conduit
- Removing the lifting beam
- Installing the water hose
- Fitting the remaining screws to the gearbox/starter motor
- Installing the gear selector cables and oil line
- Installing service clips
- Installing engine compartment components
- Finishing
- Installing the gearbox (AW55-50 2000)
- Notes
- Installation
- Notes
- Installing the gearbox
- Installing and tightening the screws to the gearbox
- Fitting the torque converter screws.
- Lifting the engine/gearbox
- Installing the rear engine mounting
- Installing the angle gear
- Installing the lower oil pipe to the gearbox
- Installing the left-hand drive shaft to the gearbox and the wheel spindle
- Fitting the subframe to the body
- Installing the right-hand drive shaft to the gearbox, wheel spindle and link arm
- Tightening the subframe screws (both sides)
- Fitting the screws for engine pads and the torque rod bracket in the gearbox
- Installing the steering wheel shaft joint
- Installing the collision protection system over the steering gear
- Installing the crossmembers
- Installing and tightening the front suspension components
- Installing the cable conduit
- Removing the lifting beam
- Installing the water hose
- Fitting the remaining screws to the gearbox/starter motor
- Installing the gear selector cables and oil line
- Installing service clips
- Installing engine compartment components
- Finishing
- Installing the gearbox (Other transmissions)
- Cleaning and lubricating the input shaft
- Checking before installing
- Adjusting the position of the engine and gearbox
- Installing and tightening the screws for the gearbox
- Installing the screw and clamp on the gearbox
- Installing the collision protection system over the steering gear (right-hand drive cars)
- Lifting the engine and gearbox to the horizontal position
- Installing the rear engine mounting
- Installing the exhaust pipe on the turbocharger (TC) and the starter motor on the engine
- Installing the subframe on the bodywork
- Installing the sealing ring for the CV joint housing
- Installing the left drive shaft on the gearbox, stub axle and control arm
- Installing the screws for the front engine pad
- Installing the delivery line on the rubber hoses and torque rod screws
- Installing and tightening the screw for the rear engine pad
- Installing the cross member
- Installing the right drive shaft on the gearbox, stub axle and control arm
- Installing new lock nuts on the steering gear
- Installing and tightening front end components (both sides)
- Tightening the ball joint pinion
- Checking the gearbox fluid level
- Installing the screw on the cable conduit
- Installing the wing liner
- Lowering the car and removing the lifting beam and lifting tools from the engine
- Installing the torque control arm
- Installing the remaining screws on the gearbox and starter motor
- Installing the gearbox cable bracket on the gearbox and the cables on the levers
- Installing service clips
- Installing the clutch pipe on the junction
- Installing the air hose on the turbocharger (TC) and the delivery line on the manifold
- Installing the coolant hose
- Installing the air cleaner (ACL) housing and the torque rod in the engine compartment
- Checking the steering gear bearing in the boot at the firewall
- Installing the engine cover
- Oil grade, checking (B5254T4, TF-80SC AWD; 2006-2007)
- Oil grade, checking (AW50/51 AWD; W55-50/51SN; 2003-2009)
- Oil grade, checking, Other (TF-80SC D5244TX 2006-)
- Oil level, checking (AW50/51 AWD; W55-50/51SN; 2003-2009)
- Oil level, checking (B5254T4, TF-80SC AWD; 2006-2007)
- Oil pump active on demand coupling (AOC), replacing