Common Specs & Procedures
SPECIFICATIONS INDEX - XC90
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning |
|||
| Service Procedures | CLIMATE UNITS - CLEANING, INSPECTION AND ADJUSTMENT | ||
| Service Specifications | AC COMPRESSOR | ||
| Torque | SUMMARY OF TIGHTENING TORQUES FOR SPECIFIC COMPONENTS | ||
| Axle Nut/Hub Nut | |||
| Torque | Tighten the screws for the hub alternately. See HUB AND BEARING First Step: tighten to 20 Nm Second Step: tighten to 140 Nm |
||
| Battery | BATTERY MARKING | ||
| Brakes | |||
| Bleeding Sequence | BRAKE SYSTEM BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | WHEEL BRAKE - SPECIFICATIONS, MECHANICAL | ||
| Torque | SUMMARY OF SPECIFIC COMPONENTS AND TIGHTENING TORQUES | ||
| Charging | |||
| Torque | SUMMARY OF TIGHTENING TORQUES FOR SPECIFIC COMPONENTS | ||
| Drive Belts | |||
| Adjustment | Drive Belt is self-adjusting | ||
| Drive Belt Routing | |||
| 2.5L engine: | see illustration under CHECKING THE AUXILIARIES BELT AND BELT TENSIONER | ||
| 4.4L engine: | see illustration under REMOVING THE AUXILIARIES BELT | ||
| Engine Cooling | |||
| General Service Specifications | WATER QUALITY | ||
| Thermostat R & I | |||
| 2.5L engine: | THERMOSTAT / TEMPERATURE SENSOR | ||
| 4.4L engine: | THERMOSTAT, REPLACING | ||
| Water Pump R & I | |||
| 2.5L engine: | COOLANT PUMP, REPLACING | ||
| 4.4L engine: | COOLANT PUMP, REPLACING | ||
| Engine Mechanical | |||
| Compression | 2.5L engine.............................. 9.0:1 4.4L engine............................ 10.4:1 |
||
| Oil Pressure @ 100°C | |||
| 2.5L engine: | see "Oil Pressure" table in ENGINE OIL | ||
| 4.4L engine: | OIL PRESSURE, SPECIFICATIONS | ||
| Overhaul | |||
| 2.5L engine: | SPECIFICATIONS, MECHANICAL | ||
| 4.4L engine: | ENGINE | ||
| Torque | |||
| 2.5L engine: | TIGHTENING TORQUE | ||
| 4.4L engine: | TIGHTENING TORQUE | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate | |||
| Torque | 33 ft. lb (45 N. m) and then angle tighten an additional 65° | ||
| Fuel System | |||
| Pressure Specification | |||
| 2.5L engine: | 375-395 kPa | ||
| 4.4L engine: | 380 ± 30 kPa | ||
| Checking Fuel Pressure | |||
| 2.5L engine: | FUEL SYSTEM PRESSURE, CHECKING | ||
| 4.4L engine: | FUEL SYSTEM PRESSURE, CHECKING | ||
| Fuel Filter R & I (all engines) | REPLACING THE FUEL FILTER | ||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Spark Plug | |||
| 2.5L engine: | BOSCH FR7DPP | ||
| 4.4L engine: | NGK Laser Iridium IFR6B11 | ||
| Gap | 2.5L engine....................... 0.7 mm | ||
| 4.4L engine....................... 1.1 mm | |||
| Torque (all engines) | 22 ft. lbs. (30 N.m) | ||
| Starter | |||
| Torque (all engines) | Starter-To-Engine Bolts: 40 Nm Starter B+ terminal: 11 Nm |
||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT AND TIGHTENING TORQUE - INSPECTION AND ADJUSTMENT | ||
| Torque | SUMMARY OF TIGHTENING TORQUES FOR SPECIFIC COMPONENTS | ||
| Wheel & Tire | |||
| Lug Nut | WHEELS | ||