Brake Control Module (BCM) Diagnostic Trouble Code (DTC) Diagnostics
- BCM-0061: Brake Discs. Temperature Too High (2002-2007)
- BCM-0065: Stop Lamp Switch. Faulty Signal (2002-2007)
- BCM-0068: Sensor Power Supply. Faulty Signal (2002-2007)
- BCM-0070: Power Supply For The Pump Motor. Faulty Signal (2002-2007)
- BCM-0071: Pump Motor. Signal Missing (2002-2007)
- BCM-0072: Pump Motor. Mechanical Fault (2002-2007)
- BCM-0074: Hydraulic Valves. Faulty Signal (2002-2007)
- BCM-0076: Control Module. Faulty Configuration (2002-2007)
- Diagnostic trouble code (DTC) information
- Faulty configuration
- Preparation
- Fault-tracing information
- Checking diagnostic trouble codes (DTCs) in the central electronic module (CEM)
- Checking the software
- Erasing diagnostic trouble codes (DTCs)
- Reading off diagnostic trouble codes (DTCs)
- Checking the car configuration
- Checking the brake system
- Resetting and configuring the brake control module (BCM)
- Resetting and configuring the control module
- Information
- Preparation
- BCM-0080: Lateral Accelerometer. Incorrect Offset Value (2002-2007)
- BCM-0081: Accelerometer. Incorrect Offset Value (2002-2007)
- BCM-0082: Yaw Rate Sensor. Incorrect Offset Value (2002-2007)
- BCM-0083: Angle Of Lean Sensor. Incorrect Offset Value (2005-2007)
- BCM-0090: Lateral Accelerometer. Faulty Signal (2002-2007)
- BCM-0091: Accelerometer. Faulty Signal (2002-2007)
- BCM-0092: Yaw Rate Sensor. Faulty Signal (2002-2007)
- BCM-0093: Angle Of Lean Sensor. Faulty Signal (2005-2007)
- BCM-0094: Communication Between Control Units Communication Problems With DEM (2002-2007)
- BCM-0095: Communication Between Control Units Communication Problems With DEM (2002)
- BCM-0095: Communication Between Control Units Communication Problems With DEM (2003-2007)
- BCM-0097: Communication Between Control Modules. Communication Problems With The Central Electronic Module (CEM) (2002-2007)
- BCM-0100: Communication Between Control Modules. Communication Problems With The Engine Control Module (ECM) (2002-2007)
- BCM-0101: Communication Between Control Modules. Communication Problems With The Engine Control Module (ECM) (2002-2007)
- BCM-0103: Pedal Position Sensor. Faulty Signal (2002-2007)
- BCM-0106: Steering Wheel Or Wheel Alignment. Incorrect Steering Wheel Or Wheel Alignment (2002-2007)
- BCM-0108: Communication Between Control Modules. Communication With The Steering Angle Sensor. Control Module Not Initiated (2002-2007)
- BCM-0109: Communication Between Control Modules. Communication With The Steering Angle Sensor. Internal Fault (2002-2004)
- BCM-0109: Communication Between Control Modules. Communication With The Steering Angle Sensor. Internal Fault (2005-2007)
- BCM-0111: Communication Between Control Modules. Check Of The Steering Angle Sensor Tolerances Has Not Been Run (2002-2007)
- BCM-0112: Active Yaw Control Sensor. Sensor Not Calibrated (2002-2007)
- BCM-0113: Back-Up (Reversing) Signal. Signal Missing (2002-2007)
- BCM-0114: Communication With The Active Yaw Control Sensor. Signal Missing (2002-2007)
- BCM-0115: Communication Between Control Modules. Communication With The Steering Angle Sensor. Signal Missing (2002-2007)
- BCM-0116: Communication With The Active Yaw Control Sensor. Communication Problems (2002-2007)
- BCM-0117: Communication With The Active Yaw Control Sensor. An Incorrect Active Yaw Control Sensor Had Been Installed (2002-2007)
- BCM-0118: Power Supply For The Active Yaw Control Sensor. Voltage Too High (2002-2007)
- BCM-0119: Power Supply For The Active Yaw Control Sensor. Voltage Too Low (2002-2007)
- BCM-0121: Yaw Rate Sensor. Signal Outside Its Permitted Range (2002-2007)
- BCM-0123: Active Yaw Control Sensor. Internal Fault (2005-2007)
- BCM-0123: Active Yaw Control Sensor. Internal Fault (2002-2004)
- BCM-0125: Lateral Accelerometer. Signal Outside Its Permitted Range (2002-2007)
- BCM-0127: Angle Of Lean Sensor. Signal Outside Its Permitted Range (2005-2007)
- BCM-0129: Accelerometer. Signal Outside Its Permitted Range (2002-2007)
- BCM-0130: Brake Pressure Sensor 1. Signal Too Low (2002-2007)
- BCM-0133: Brake Pressure Sensor 2. Signal Too Low (2002-2007)
- BCM-0136: Brake Pressure Sensor 1 And 2. Signal Outside Its Permitted Range (2002-2007)
- BCM-0138: Power Supply For The Active Yaw Control Sensor. Faulty Voltage (2002-2007)
- BCM-0139: Pressure Build-Up Valve, Power Brake Booster. Signal Outside Its Permitted Range (2002-2007)
- BCM-0140: Pedal Pressure Sensor. Signal Outside Its Permitted Range (2002-2007)
- BCM-0145: Stability Control. Too Long Stability Control (2002-2007)
- BCM-0146: Factory Test, Dynamic Stability And Traction Control (DSTC). Test Cycle Not Approved (2002-2007)
- BCM-0147: Pedal Position Sensor. Signal Outside Its Permitted Range (2002-2007)
- BCM-0148: Communication Between Control Modules. Faulty Configuration Id (2002-2007)
- BCM-0150: Stop Lamp Switch. Signal Outside Its Permitted Range (2002-2007)
- BCM-0151: Control Module. Internal Memory Fault (2002-2007)
- BCM-A030: Communication Between Control Modules. Steering Angle Sensor. Initialization Check Not Run (2005-2007)
- BCM-A030: Communication Between Control Modules. Steering Angle Sensor. Initialization Check Not Run (2002-2004)
- BCM-A031: Communication Between Control Modules. Steering Angle Sensor. Tolerance Check Not Run (2002-2007)
- BCM-A032: Stability Function. Too Long Stability Control (2003-2007)
- BCM-E000: Control Module Communication. Faulty Communication (2005-2007)
- BCM-E000: Control Module Communication. Faulty Communication (2002-2004)
- BCM-E003: Configuration Fault. Faulty Configuration (2005-2007)
- BCM-E003: Configuration Fault. Faulty Configuration (2002-2004)
- BCM-XXXX: Unknown Diagnostic Trouble Code (DTC) For The Current Control Module Version (2002-2007)