Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Toyota >> 2021 >> Prius LE AWD-e >> Repair and Diagnosis >> Body & Frame >> Windows >> Power Window Control System - Diagnostics & Symptom Tests >> Power Window Control System >> DTC B2311: Power Window Motor Malfunction [11/2015 - ] >> Procedure

DTC B2311: Power Window Motor Malfunction [11/2015 - ]: Procedure

  1. CHECK FOR DTC 
    1. Clear the DTCs.

      Refer to DTC CHECK / CLEAR [11/2015 - ]

      Body Electrical > D-Door Motor > Clear DTCs 

      Body Electrical > P-Door Motor > Clear DTCs 

      Body Electrical > RL-Door Motor > Clear DTCs 

      Body Electrical > RR-Door Motor > Clear DTCs 

    2. Check for DTCs.

      Refer to DTC CHECK / CLEAR [11/2015 - ]

      Body Electrical > D-Door Motor > Trouble Codes 

      Body Electrical > P-Door Motor > Trouble Codes 

      Body Electrical > RL-Door Motor > Trouble Codes 

      Body Electrical > RR-Door Motor > Trouble Codes 

      OK

      DTC B2311 is not output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2015 - 12/2018]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [12/2018 - 07/2020]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [07/2020 - 06/2021]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2021 - ] 

    Result: 

    NG 

    See step  2

  2. CHECK DTC OUTPUT 
    1. Check the parts from which this DTC has been output.

      Result

      Result Proceed to
      DTC output from power window regulator motor assembly (for driver door) A
      DTC output from power window regulator motor assembly (for front passenger door) B
      DTC output from power window regulator motor assembly (for rear LH door) C
      DTC output from power window regulator motor assembly (for rear RH door) D

    Result: 

    B 

    See step  4

    Result: 

    C 

    See step  5

    Result: 

    D 

    See step  6

    Result: 

    A 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND) 
    1. Measure the voltage according to the value(s) in the table below.
      GTY578833Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Power Window Regulator Motor Assembly (for Driver Door))

      Standard Voltage

      (J2)

      (J2)

      Tester Connection Condition Specified Condition
      J2-2 (B) - J2-1 (GND) Power switch off 11 to 14 V
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      (J2)

      (J2)

      Tester Connection Condition Specified Condition
      J2-1 (GND) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  7

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) - AUXILIARY BATTERY AND BODY GROUND) 
    1. Measure the voltage according to the value(s) in the table below.
      GTY578819Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Power Window Regulator Motor Assembly (for Front Passenger Door))

      Standard Voltage

      (I2)

      (I2)

      Tester Connection Condition Specified Condition
      I2-2 (B) - I2-1 (GND) Power switch off 11 to 14 V
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      (I2)

      (I2)

      Tester Connection Condition Specified Condition
      I2-1 (GND) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  7

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR) - AUXILIARY BATTERY AND BODY GROUND) 
    1. Measure the voltage according to the value(s) in the table below.
      GTY578820Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Power Window Regulator Motor Assembly (for Rear LH Door))

      Standard Voltage

      (L3)

      (L3)

      Tester Connection Condition Specified Condition
      L3-2 (B) - L3-1 (GND) Power switch off 11 to 14 V
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      (L3)

      (L3)

      Tester Connection Condition Specified Condition
      L3-1 (GND) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  7

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  6. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR) - AUXILIARY BATTERY AND BODY GROUND) 
    1. Measure the voltage according to the value(s) in the table below.
      GTY578822Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Power Window Regulator Motor Assembly (for Rear RH Door))

      Standard Voltage

      (K2)

      (K2)

      Tester Connection Condition Specified Condition
      K2-2 (B) - K2-1 (GND) Power switch off 11 to 14 V
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      (K2)

      (K2)

      Tester Connection Condition Specified Condition
      K2-1 (GND) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  7

  7. PERFORM ACTIVE TEST USING TECHSTREAM (APPLICABLE LOCATION) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / (desired system) / Active Test.

      HINT: 

      Perform the Active Test for the power window regulator motor assembly that has DTC B2311 stored in its ECU.

    5. Perform the Active Test according to the display on the Techstream.
      WARNING:

      Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.

      Body Electrical > D-Door Motor > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Power Window Power window OFF / DOWN / UP -

      Body Electrical > P-Door Motor > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Power Window Power window OFF / DOWN / UP -

      Body Electrical > RL-Door Motor > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Power Window Power window OFF / DOWN / UP -

      Body Electrical > RR-Door Motor > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Power Window Power window OFF / DOWN / UP -

      Body Electrical > D-Door Motor > Active Test 

      Tester Display
      Power Window

      Body Electrical > P-Door Motor > Active Test 

      Tester Display
      Power Window

      Body Electrical > RL-Door Motor > Active Test 

      Tester Display
      Power Window

      Body Electrical > RR-Door Motor > Active Test 

      Tester Display
      Power Window

      OK

      Each power window operates normally.

      Result

      Result Proceed to
      OK A
      NG (Driver door power window) B
      NG (Front passenger door power window)
      NG (Rear LH door power window) C
      NG (Rear RH door power window)

    Result: 

    B 

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR OR FRONT PASSENGER DOOR). Refer to  REMOVAL [11/2015 - 12/2018]  , or refer to  REMOVAL [12/2018 - 07/2020]  , or refer to  REMOVAL [07/2020 - ] 

    Result: 

    C 

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR OR REAR RH DOOR). Refer to  REMOVAL [11/2015 - 12/2018]  , or refer to  REMOVAL [12/2018 - 07/2020]  , or refer to  REMOVAL [07/2020 - ] 

    Result: 

    A 

    See step  8

  8. PERFORM INITIALIZATION (APPLICABLE LOCATION) 
    1. Initialize the power window regulator motor assembly.

      Refer to INITIALIZATION [11/2015 - ]

      HINT: 

      Initialize the power window regulator motor assembly that has DTC B2311 stored in its ECU.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  9

  9. CHECK POWER WINDOW CONTROL SYSTEM (APPLICABLE LOCATION) 
    1. Check that the power window operates normally by opening and closing it.

      Refer to OPERATION CHECK [11/2015 - 12/2018] , or refer to OPERATION CHECK [12/2018 - ]

      HINT: 

      Check the power window operation of the window where DTC B2311 has been stored.

      OK

      Each power window operates normally.

      Result

      Result Proceed to
      OK A
      NG (Driver door power window) B
      NG (Front passenger door power window)
      NG (Rear LH door power window) C
      NG (Rear RH door power window)

    Result: 

    B 

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR OR FRONT PASSENGER DOOR). Refer to  REMOVAL [11/2015 - 12/2018]  , or refer to  REMOVAL [12/2018 - 07/2020]  , or refer to  REMOVAL [07/2020 - ] 

    Result: 

    C 

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR OR REAR RH DOOR). Refer to  REMOVAL [11/2015 - 12/2018]  , or refer to  REMOVAL [12/2018 - 07/2020]  , or refer to  REMOVAL [07/2020 - ] 

    Result: 

    A 

    See step  10

  10. CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY 
    1. Check that the power window components are installed correctly.

      OK

      Power window components are installed correctly.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    INSTALL PARTS CORRECTLY 

    Result: 

    OK 

    See step  11

  11. CHECK DTC OUTPUT 
    1. Turn the power switch off.
    2. Wait for at least 10 seconds, and then turn the power switch on (IG).
    3. Check for DTCs.

      Refer to DTC CHECK / CLEAR [11/2015 - ]

      Body Electrical > D-Door Motor > Trouble Codes 

      Body Electrical > P-Door Motor > Trouble Codes 

      Body Electrical > RL-Door Motor > Trouble Codes 

      Body Electrical > RR-Door Motor > Trouble Codes 

      OK

      B2311 is not output.

      Result

      Result Proceed to
      OK A
      NG (Driver door power window) B
      NG (Front passenger door power window)
      NG (Rear LH door power window) C
      NG (Rear RH door power window)

    Result: 

    A 

    END 

    Result: 

    B 

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FOR DRIVER DOOR OR FRONT PASSENGER DOOR). Refer to  REMOVAL [11/2015 - 12/2018]  , or refer to  REMOVAL [12/2018 - 07/2020]  , or refer to  REMOVAL [07/2020 - ] 

    Result: 

    C 

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR OR REAR RH DOOR). Refer to  REMOVAL [11/2015 - 12/2018]  , or refer to  REMOVAL [12/2018 - 07/2020]  , or refer to  REMOVAL [07/2020 - ] 

scientia non olet · About Mike's Workshop Manuals