Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Toyota >> 2017 >> Yaris iA Standard Trans >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Cruise Control Systems >> Cruise Control System (Diagnostics -- Introduction) >> Cruise Control System >> Diagnostic Trouble Code Chart >> Diagnostic Trouble Code Chart

Diagnostic Trouble Code Chart

LASER SENSOR

DTC No. Detection Item DTC Detection Condition Warning Indicate Memory Fail-safe Operation Note Link
U000100 High Speed CAN Communication Bus CAN line
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U000100: High Speed CAN Communication Bus; DTC U010000: Lost Communication With ECM/PCM "A"; DTC U012100: Lost Communication With Anti-Lock Brake System (ABS) Control Module; DTC U013100: Lost Communication With Power Steering Control Module; DTC U015500: Lost Communication With Instrument Panel Cluster (IPC) Control Module
U0100/5C-61 Lost Communication with ECM / PCM "A" Pre-collision system
  • Pre-collision warning light (amber): Illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U300066: Control Module signal has too many transitions / events
U010000 Lost Communication With ECM/PCM "A" CAN line
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U000100: High Speed CAN Communication Bus; DTC U010000: Lost Communication With ECM/PCM "A"; DTC U012100: Lost Communication With Anti-Lock Brake System (ABS) Control Module; DTC U013100: Lost Communication With Power Steering Control Module; DTC U015500: Lost Communication With Instrument Panel Cluster (IPC) Control Module
U012100 Lost Communication With Anti-Lock Brake System (ABS) Control Module CAN line
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U000100: High Speed CAN Communication Bus; DTC U010000: Lost Communication With ECM/PCM "A"; DTC U012100: Lost Communication With Anti-Lock Brake System (ABS) Control Module; DTC U013100: Lost Communication With Power Steering Control Module; DTC U015500: Lost Communication With Instrument Panel Cluster (IPC) Control Module
U013100 Lost Communication With Power Steering Control Module CAN line
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U000100: High Speed CAN Communication Bus; DTC U010000: Lost Communication With ECM/PCM "A"; DTC U012100: Lost Communication With Anti-Lock Brake System (ABS) Control Module; DTC U013100: Lost Communication With Power Steering Control Module; DTC U015500: Lost Communication With Instrument Panel Cluster (IPC) Control Module
U015500 Lost Communication With Instrument Panel Cluster (IPC) Control Module CAN line
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U000100: High Speed CAN Communication Bus; DTC U010000: Lost Communication With ECM/PCM "A"; DTC U012100: Lost Communication With Anti-Lock Brake System (ABS) Control Module; DTC U013100: Lost Communication With Power Steering Control Module; DTC U015500: Lost Communication With Instrument Panel Cluster (IPC) Control Module
U040100 Invalid Data Received from ECM/PCM A Signal error from ECM
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U040100: Invalid Data Received from ECM/PCM A; DTC U040182: Invalid Data Received from ECM/PCM A alive / sequence counter incorrect / not updated
U040182 Invalid Data Received from ECM/PCM A alive / sequence counter incorrect / not updated Signal error from ECM
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U040100: Invalid Data Received from ECM/PCM A; DTC U040182: Invalid Data Received from ECM/PCM A alive / sequence counter incorrect / not updated
U041500 Invalid Data Received From Anti-Lock Brake System (ABS) Control Module Signal error from Brake actuator
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U041500: Invalid Data Received From Anti-Lock Brake System (ABS) Control Module; DTC U041568: Invalid Data Received From Anti-Lock Brake System (ABS) Control Module event information; DTC U041582: Invalid Data Received From Anti-Lock Brake System (ABS) Control Module alive / sequence counter incorrect / not update
U041568 Invalid Data Received From Anti-Lock Brake System (ABS) Control Module event information Signal error from Brake actuator
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U041500: Invalid Data Received From Anti-Lock Brake System (ABS) Control Module; DTC U041568: Invalid Data Received From Anti-Lock Brake System (ABS) Control Module event information; DTC U041582: Invalid Data Received From Anti-Lock Brake System (ABS) Control Module alive / sequence counter incorrect / not update
U041582 Invalid Data Received From Anti-Lock Brake System (ABS) Control Module alive / sequence counter incorrect / not update Signal error from Brake actuator
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U041500: Invalid Data Received From Anti-Lock Brake System (ABS) Control Module; DTC U041568: Invalid Data Received From Anti-Lock Brake System (ABS) Control Module event information; DTC U041582: Invalid Data Received From Anti-Lock Brake System (ABS) Control Module alive / sequence counter incorrect / not update
U042000 Invalid Data Received From Power Steering Control Module Signal error from power steering ECU
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U042000: Invalid Data Received From Power Steering Control Module; DTC U042082: Invalid Data Received From Power Steering Control Module alive / sequence counter incorrect / not updated
U042082 Invalid Data Received From Power Steering Control Module alive / sequence counter incorrect / not updated Signal error from power steering ECU
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U042000: Invalid Data Received From Power Steering Control Module; DTC U042082: Invalid Data Received From Power Steering Control Module alive / sequence counter incorrect / not updated
U042300 Invalid Data Received From Power Steering Control Module Signal error from combination meter
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U042300: Invalid Data Received From Power Steering Control Module; DTC U042382: Invalid Data Received from Instrument Panel Cluster Control Module alive / sequence counter incorrect / not updated
U042382 Invalid Data Received from Instrument Panel Cluster Control Module alive / sequence counter incorrect / not updated Signal error from combination meter
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U042300: Invalid Data Received From Power Steering Control Module; DTC U042382: Invalid Data Received from Instrument Panel Cluster Control Module alive / sequence counter incorrect / not updated
U1A1449 CAN Initialisation Failure internal electronic failure Laser sensor
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U1A1449: CAN Initialisation Failure internal electronic failure
U230054 Central Configuration missing calibration Laser sensor configuration
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U230054: Central Configuration missing calibration; DTC U230055: Central Configuration not configured; DTC U230056: Central Configuration invalid / incompatible configuration; DTC U230064: Central Configuration signal plausibility failure
U230055 Central Configuration not configured Laser sensor configuration
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U230054: Central Configuration missing calibration; DTC U230055: Central Configuration not configured; DTC U230056: Central Configuration invalid / incompatible configuration; DTC U230064: Central Configuration signal plausibility failure
U230056 Central Configuration invalid / incompatible configuration Laser sensor configuration
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U230054: Central Configuration missing calibration; DTC U230055: Central Configuration not configured; DTC U230056: Central Configuration invalid / incompatible configuration; DTC U230064: Central Configuration signal plausibility failure
U230064 Central Configuration signal plausibility failure Laser sensor configuration
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U230054: Central Configuration missing calibration; DTC U230055: Central Configuration not configured; DTC U230056: Central Configuration invalid / incompatible configuration; DTC U230064: Central Configuration signal plausibility failure
U300000 Control Module Laser sensor (internal malfunction)
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U300000: Control Module; DTC U300064: Control Module signal plausibility failure
U300064 Control Module signal plausibility failure Laser sensor (internal malfunction)
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U300000: Control Module; DTC U300064: Control Module signal plausibility failure
U300316 Battery Voltage circuit voltage below threshold Battery power supply
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U300316: Battery Voltage circuit voltage below threshold; DTC U300317: Battery Voltage circuit voltage above threshold
U300317 Battery Voltage circuit voltage above threshold Battery power supply
  • Pre-collision warning light (amber): Not illuminate
 DTC Stored Applicable
  • Pre-collision control: Control disabled
  • Drive cycle: Not applicable
  • Self test type: CMDTC self test
 Refer to DTC U300316: Battery Voltage circuit voltage below threshold; DTC U300317: Battery Voltage circuit voltage above threshold
scientia non olet · About Mike's Workshop Manuals