Rear Power Window RH does not Operate with Rear Power Window Switch RH: Procedure

1. Disconnect the K1 power window regulator switch assembly (for rear RH door) connector.
2. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   K1-3 (B) - Body ground	Ignition switch ON (IG)	11 to 14 V

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Remove the power window regulator switch assembly (for rear RH door). Refer to REMOVAL .
   Fig 1: Power Window Regulator Switch Connector

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Measure the resistance when the switch is operated according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   1 (D) - 2 (SD)	UP	Below 1 Ω
   3 (B) - 4 (U)		Below 1 Ω
   1 (D) - 2 (SD)	off	Below 1 Ω
   4 (U) - 5 (SU)		Below 1 Ω
   4 (U) - 5 (SU)	DOWN	Below 1 Ω
   1 (D) - 3 (B)		Below 1 Ω

   TEXT IN ILLUSTRATION
   
   

   *a	Component without harness connected (Power Window Regulator Switch Assembly (for Rear RH Door))

NG → See step   6 

OK: Go to next step 

1. Disconnect the K2 power window regulator motor assembly RH (for rear RH door) connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   K1-4 (U) - K2-1 (U)	Always	Below 1 Ω
   K1-1 (D) - K2-2 (D)	Always	Below 1 Ω
   K1-4 (U) - Body ground	Always	10 kΩ or higher
   K1-1 (D) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Remove the power window regulator master switch assembly. Refer to REMOVAL .
   Fig 2: Power Window Regulator Master Switch

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Measure the resistance when the switch is operated according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   6 (B) - 10 (U)	UP	Below 1 Ω
   1 (E) - 18 (D)		Below 1 Ω
   1 (E) - 10 (U)	off	Below 1 Ω
   1 (E) - 18 (D)		Below 1 Ω
   6 (B) - 18 (D)	DOWN	Below 1 Ω
   1 (E) - 10 (U)		Below 1 Ω

   TEXT IN ILLUSTRATION
   
   

   *a	Component without harness connected (Power Window Regulator Master Switch Assembly)

NG → See step   8 

OK: Go to next step 

1. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   J1-10 (U) - K1-5 (SU)	Always	Below 1 Ω
   J1-18 (D) - K1-2 (SD)	Always	Below 1 Ω
   J1-10 (U) - Body ground	Always	10 kΩ or higher
   J1-18 (D) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK → See step   7