Rear Power Window LH does not Operate with Rear Power Window Switch LH: Procedure

1. Disconnect the L1 power window regulator switch assembly (for rear LH door) connector.
2. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   L1-3 (B) - Body ground	Ignition switch ON (IG)	11 to 14 V

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Remove the power window regulator switch assembly (for rear LH door). Refer to REMOVAL .
   Fig 1: Power Window Regulator Switch Connector

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Measure the resistance when the switch is operated according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   1 (D) - 2 (SD)	UP	Below 1 Ω
   3 (B) - 4 (U)		Below 1 Ω
   1 (D) - 2 (SD)	off	Below 1 Ω
   4 (U) - 5 (SU)		Below 1 Ω
   4 (U) - 5 (SU)	DOWN	Below 1 Ω
   1 (D) - 3 (B)		Below 1 Ω

   TEXT IN ILLUSTRATION
   
   

   *a	Component without harness connected (Power Window Regulator Switch Assembly (for Rear LH Door))

NG → See step   6 

OK: Go to next step 

1. Disconnect the L2 power window regulator motor assembly LH (for rear LH door) connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   L1-4 (U) - L2-1 (U)	Always	Below 1 Ω
   L1-1 (D) - L2-2 (D)	Always	Below 1 Ω
   L1-4 (U) - Body ground	Always	10 kΩ or higher
   L1-1 (D) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Remove the power window regulator master switch assembly. Refer to REMOVAL .
   Fig 2: Power Window Regulator Master Switch Connector

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Measure the resistance when the switch is operated according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   6 (B) - 12 (U)	UP	Below 1 Ω
   1 (E) - 13 (D)		Below 1 Ω
   1 (E) - 12 (U)	off	Below 1 Ω
   1 (E) - 13 (D)		Below 1 Ω
   6 (B) - 13 (D)	DOWN	Below 1 Ω
   1 (E) - 12 (U)		Below 1 Ω

   TEXT IN ILLUSTRATION
   
   

   *a	Component without harness connected (Power Window Regulator Master Switch Assembly)

NG → See step   8 

OK: Go to next step 

1. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   J1-12 (U) - L1-5 (SU)	Always	Below 1 Ω
   J1-13 (D) - L1-2 (SD)	Always	Below 1 Ω
   J1-12 (U) - Body ground	Always	10 kΩ or higher
   J1-13 (D) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK → See step   7