Rear Power Window RH does not Operate with Rear Power Window Switch RH: Procedure

1. Remove the rear power window regulator switch assembly RH.
2. Measure the resistance according to the value(s) in the table below.
   Fig 1: Identifying Rear Power Window Regulator Switch Assembly RH Connector Terminals

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Standard Resistance

   Tester Connection	Switch Condition	Specified Condition
   1 (U) - 3 (B) 4 (SD) - 5 (D)	UP	Below 1 Ω
   2 (SU) - 1 (U) 4 (SD) - 5 (D)	OFF	Below 1 Ω
   2 (SU) - 1 (U) 3 (B) - 5 (D)	DOWN	Below 1 Ω

   TEXT IN ILLUSTRATION
   
   

   *a	Component without harness connected (Power Window Regulator Switch Assembly RH)

NG → REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH 

OK: Go to next step 

1. Remove the rear power window regulator motor assembly RH.
2. Apply battery voltage to connector terminals 1 and 2.
3. Check that the motor smoothly rotates.
   Fig 2: Inspecting Rear Power Window Regulator Motor Assembly RH

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   NOTE:

   Do not apply battery voltage to any terminals except terminals 1 and 2.

   OK

   Measurement Condition	Specified Condition
   Battery positive (+) → 2 Battery negative (-) → 1	Motor gear rotates clockwise
   Battery positive (+) → 1 Battery negative (-) → 2	Motor gear rotates counterclockwise

   TEXT IN ILLUSTRATION
   
   

   *1	Motor Gear
   *a	Clockwise
   *b	Counterclockwise
   *c	Component without harness connected (Rear Power Window Regulator Motor Assembly)

NG → REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH 

OK: Go to next step 

1. Disconnect the P16 rear power window regulator switch assembly RH connector.
   Fig 3: Identifying P16 Connector Terminals

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Switch Condition	Specified Condition
   P16-3 (B) - Body ground	Ignition switch ON	11 to 14 V

   TEXT IN ILLUSTRATION
   
   

   *a	Front view of wire harness connector (to Rear Power Window Regulator Switch Assembly RH)

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Disconnect the P16 rear power window regulator switch assembly RH connector.
2. Disconnect the P13 rear power window regulator motor assembly RH connector.
3. Measure the resistance according the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   P16-1 (U) - P13-2	Always	Below 1 Ω
   P16-5 (D) - P13-1	Always	Below 1 Ω
   P16-1 (U) - Body ground	Always	10 kΩ or higher
   P16-5 (D) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Disconnect the P16 rear power window regulator switch assembly RH connector.
2. Disconnect the P9 power window regulator master switch assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   P16-2 (SU) - P9-10	Always	Below 1 Ω
   P16-4 (SD) - P9-18	Always	Below 1 Ω
   P16-2 (SU) - Body ground	Always	10 kΩ or higher
   P16-4 (SD) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK → REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY