Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Toyota >> 2012 >> Prius Three >> Repair and Diagnosis >> Accessories & Equipment >> Cruise Control Systems >> Cruise Control System (Except Plug-In) (Diagnostics - Introduction) >> Cruise Control System >> Terminals Of Ecu >> Terminals Of Ecu

Terminals Of Ecu

  1. CHECK POWER MANAGEMENT CONTROL ECU 
    Fig 1: Power Management Control ECU Connector Terminal Identification
    GTY216144Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
    A22-7 (ST1-) - L5-6 (E1) R - BR Stop light switch signal Power switch on (IG), Brake pedal released 7.5 to 14 V
    A22-7 (ST1-) - L5-6 (E1) R - BR Stop light switch signal Power switch on (IG), Brake pedal depressed Below 1 V
    A22-23 (STP) - L5-6 (E1) L - BR Stop light switch signal Brake pedal released Below 1 V
    A22-23 (STP) - L5-6 (E1) L - BR Stop light switch signal Brake pedal depressed 7.5 to 14 V
    L5-6 (E1) - Body ground BR - Body ground Earth (ground) circuit of power management control ECU Always Below 1 Ω
    L5-11 (TC) - L5-6 (E1) P - BR Terminal TC of DLC3 Power switch on (IG) 11 to 14 V
    L5-11 (TC) - L5-6 (E1) P - BR Terminal TC of DLC3 Terminals TC and CG of DLC3 connected Below 1 V
    L5-14 (SPDI) - L5-6 (E1) V - BR Vehicle speed signal Driving at 20 km/h (12 mph) Pulse generation
    (see waveform 1)
    L6-22 (CCS) - L5-6 (E1) R - BR Cruise control main switch circuit Power switch on (IG) 11 to 14 V
    L6-22 (CCS) - L5-6 (E1) R - BR Cruise control main switch circuit Power switch on (IG), MAIN switch on Below 1 V
    L6-22 (CCS) - L5-6 (E1) R - BR Cruise control main switch circuit Power switch on (IG), + RES switch on 2.3 to 4.0 V
    L6-22 (CCS) - L5-6 (E1) R - BR Cruise control main switch circuit Power switch on (IG), - SET switch on 4.5 to 7.1 V
    L6-22 (CCS) - L5-6 (E1) R - BR Cruise control main switch circuit Power switch on (IG), CANCEL switch on 6.6 to 10.1 V
    L6-24 (CA1L) - L5-6 (E1) W - BR CAN communication signal Power switch on (IG) Pulse generation
    (see waveform 2)
    L6-25 (CA1H) - L5-6 (E1) B - BR CAN communication signal Power switch on (IG) Pulse generation
    (see waveform 3)
    1. WAVEFORM 1
      Fig 2: Identifying Waveform 1
      GTY191968Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Vehicle speed signal
        Power Management Control ECU Terminal Name Between SPDI and E1
        Tester Range 5 V/DIV., 20 ms./DIV.
        Condition Driving at 20 km/h (12 mph)

        HINT: 

        • The wavelength becomes shorter as the vehicle speed increases.
        • Depending on the vehicle, the output waveform voltage may rise to 12 V if influenced by optionally installed systems.
    2. WAVEFORM 2
      Fig 3: Identifying Waveform 2
      GTY229528Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. CAN communication signal
        Power Management Control ECU Terminal Name Between CA1L and E1
        Tester Range 1 V/DIV., 10 μsec./DIV.
        Condition Power switch on (IG)

        HINT: 

        The waveform varies depending on the CAN communication signal.

    3. WAVEFORM 3
      Fig 4: Identifying Waveform 3
      GTY222725Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. CAN communication signal
        Power Management Control ECU Terminal Name Between CA1H and E1
        Tester Range 1 V/DIV., 10 μsec./DIV.
        Condition Power switch on (IG)

        HINT: 

        The waveform varies depending on the CAN communication signal.

scientia non olet · About Mike's Workshop Manuals