Radio Receiver: Installation: Installation

WARNING: This page is about a different car, the 2012 Toyota Corolla. However, it is still accessible from the selected car via links, so may be relevant.

INSTALL RADIO RECEIVER ASSEMBLY (for Radio Receiver Type without USB Audio System)
INSTALL NO. 1 RADIO BRACKET (for Radio Receiver Type without USB Audio System)
1. Install the No. 1 radio bracket with the 4 screws.
INSTALL NO. 2 RADIO BRACKET (for Radio Receiver Type without USB Audio System)
1. Install the No. 2 radio bracket with the 4 screws.
INSTALL RADIO RECEIVER ASSEMBLY (for Radio Receiver Type with USB Audio System)
INSTALL NO. 1 RADIO BRACKET (for Radio Receiver Type with USB Audio System)
1. Install the No. 1 radio bracket with the 3 screws.
INSTALL NO. 2 RADIO BRACKET (for Radio Receiver Type with USB Audio System)
1. Install the No. 2 radio bracket with the 3 screws.
INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)
INSTALL EXTENSION MODULE (for Radio and Display Type) . Refer to INSTALLATION - Step 1
INSTALL NO. 1 RADIO BRACKET (for Radio and Display Type)
1. Install the No. 1 radio bracket with the 5 screws.
INSTALL NO. 2 RADIO BRACKET (for Radio and Display Type)
1. Install the No. 2 radio bracket with the 5 screws.
INSTALL NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)
INSTALL NO. 1 RADIO BRACKET (for Navigation Receiver Type)
1. Install the No. 1 radio bracket with the 4 screws.
INSTALL NO. 2 RADIO BRACKET (for Navigation Receiver Type)
1. Install the No. 2 radio bracket with the 4 screws.
INSTALL RADIO RECEIVER WITH BRACKET (for Radio Receiver Type without USB Audio System)
1. Connect each connector.
2. Engage the 4 clips.
  WARNING:
  When installing the radio receiver with bracket, check that the wire harness and No. 2 antenna cord sub-assembly are not caught between the radio receiver with bracket and the instrument panel reinforcement assembly. Failure to do so may cause a short circuit.
3. Install the radio receiver with bracket with the 4 bolts.
INSTALL RADIO RECEIVER WITH BRACKET (for Radio Receiver Type with USB Audio System)
1. Connect each connector.
2. Install the radio receiver with bracket with the 4 bolts.
  WARNING:
  When installing the radio receiver with bracket, check that the wire harness and No. 2 antenna cord sub-assembly are not caught between the radio receiver with bracket and the instrument panel reinforcement assembly. Failure to do so may cause a short circuit.
INSTALL RADIO AND DISPLAY RECEIVER WITH BRACKET (for Radio and Display Type)
1. Connect each connector.
2. Install the radio and display receiver with bracket with the 4 bolts.
  WARNING:
  When installing the radio and display receiver with bracket, check that the wire harness and No. 2 antenna cord sub-assembly are not caught between the radio and display receiver with bracket and the instrument panel reinforcement assembly. Failure to do so may cause a short circuit.
INSTALL NAVIGATION RECEIVER WITH BRACKET (for Navigation Receiver Type)
1. Connect each connector.
2. Engage the 4 clips.
  WARNING:
  When installing the navigation receiver with bracket, check that the wire harness and No. 2 antenna cord sub-assembly are not caught between the navigation receiver with bracket and the instrument panel reinforcement assembly. Failure to do so may cause a short circuit.
3. Install the navigation receiver with bracket with the 4 bolts.
INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ USB Audio System) . Refer to INSTALLATION - Step 29
INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY . Refer to INSTALLATION - Step 12
INSTALL INSTRUMENT PANEL FINISH PANEL END LH . Refer to INSTALLATION - Step 13
INSTALL INSTRUMENT PANEL FINISH PANEL END RH . Refer to INSTALLATION - Step 14
INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH . Refer to INSTALLATION - Step 15
INSTALL LOWER INSTRUMENT PANEL FINISH PANEL RH . Refer to INSTALLATION - Step 16