Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Toyota >> 2011 >> Yaris 2D Hatchback, Standard >> Repair and Diagnosis >> Body & Frame >> Windows >> Power Window Control System (Diagnostics & Symptom Tests) >> Power Window Control System >> Symptom Tests >> Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch >> Procedure

Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch: Procedure

  1. CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE) (POWER SOURCE) 
    1. Disconnect the F1 power window regulator switch assembly connector.
      Fig 1: Identifying Power Window Regulator Switch Harness Connectors
      GTY214179Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the voltage of the wire harness side connector.

      Standard voltage

      Tester Connection Condition Specified Condition
      F1-3 - Body ground Ignition switch ON 11 to 14 V
    3. Reconnect the F1 power window regulator switch assembly connector.

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  2. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE) 
    1. Remove the power window regulator switch assembly.
      Fig 2: Identifying Power Window Regulator Switch Connectors (Component Side)
      GTY239011Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance of the switch when the switch is operated.

      Standard resistance

      Tester Connection Switch Condition Specified Condition
      3 - 4
      2 - 1      		 UP Below 1 Ω
      5 - 4
      2 - 1      		 OFF Below 1 Ω
      5 - 4
      3 - 1      		 DOWN Below 1 Ω
    3. Reinstall the power window regulator switch assembly.

    NG → REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE) 

    OK: Go to next step 

  3. CHECK HARNESS AND CONNECTOR (SWITCH (PASSENGER SIDE) - MOTOR (PASSENGER SIDE)) 
    1. Disconnect the F1 power window regulator switch assembly connector.
      Fig 3: Power Window Regulator Switch (Wire Harness Side) F1 & F4 Connector Terminals
      GTY239091Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the F4 power window regulator motor assembly connector.
    3. Measure the resistance of the wire harness side connectors.

      Standard resistance

      Tester Connection Specified Condition
      F1-1 - F4-1 Below 1 Ω
      F1-4 - F4-2 Below 1 Ω
      F1-1 or F4-1 - Body ground 10 kΩ or higher
      F1-4 or F4-2 - Body ground 10 kΩ or higher
    4. Reconnect the F1 power window regulator switch assembly connector.
    5. Reconnect the F4 power window regulator motor assembly connector.

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  4. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (PASSENGER SIDE) 
    1. Remove the power window regulator motor assembly.
      Fig 4: Testing Power Window Regulator Motor Assembly (For Passenger Side)
      GTY238945Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Apply battery voltage to connector terminals 1 and 2.
      NOTE:

      Do not apply battery voltage to any terminals except terminals 1 and 2.

    3. Check that the motor gear rotates smoothly as follows.

      OK

      Measurement Condition Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2      		 Motor gear rotates clockwise
      Battery positive (+) → 2
      Battery negative (-) → 1      		 Motor gear rotates counterclockwise
    4. Reinstall the power window regulator motor assembly.

    NG → REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (PASSENGER SIDE) 

    OK: Go to next step 

  5. CHECK HARNESS AND CONNECTOR (MASTER SWITCH - SWITCH (PASSENGER SIDE)) 
    1. Disconnect the G1 power window regulator master switch assembly connector.
      Fig 5: Identifying Power Window Regulator Master Switch Connectors (Wire Harness Side)
      GTY239258Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the F1 power window regulator switch assembly connector.
    3. Measure the resistance of the wire harness side connectors.

      Standard resistance

      3 Door

      Tester Connection Specified Condition
      G1-16 (U) - F1-5 Below 1 Ω
      G1-18 (D) - F1-2 Below 1 Ω
      G1-16 (U) or F1-5 - Body ground 10 kΩ or higher
      G1-18 (D) or F1-2 - Body ground 10 kΩ or higher

      Except 3 door

      Tester Connection Specified Condition
      G1-16 (U) - F1-5 Below 1 Ω
      G1-15 (D) - F1-2 Below 1 Ω
      G1-16 (U) or F1-5 - Body ground 10 kΩ or higher
      G1-15 (D) or F1-2 - Body ground 10 kΩ or higher
    4. Reconnect the G1 power window regulator master switch assembly connector.
    5. Reconnect the F1 power window regulator switch assembly connector.

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  6. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (FRONT PASSENGER SWITCH) 
    1. 3 Door:
      Fig 6: Power Window Regulator Master Switch Connector Terminals
      GTY236815Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Inspect the front passenger switch.

      1. Remove the power window regulator master switch.
      2. Measure the resistance of the switch when the switch is operated.

        Standard resistance

        Window Lock Switch Condition Power Window Switch Condition Tester Connection Specified Condition
        OFF UP 7 (E) - 18 (D)
        16 (U) - 15 (B)        		 Below 1 Ω
        OFF OFF 7 (E) - 16 (U)
        7 (E) - 18 (D)        		 Below 1 Ω
        OFF DOWN 7 (E) - 16 (U)
        15 (B) - 18 (D)        		 Below 1 Ω
        ON UP 7 (E) - 18 (D) 10 kΩ or higher
        16 (U) - 15 (B) Below 1 Ω
        ON OFF 16 (U) - 18 (D) Below 1 Ω
        ON DOWN 7 (E) - 16 (U) 10 kΩ or higher
        15 (B) - 18 (D) Below 1 Ω
      3. Reinstall the power window master switch.
    2. Except 3 door:
      Fig 7: Power Window Regulator Master Switch (Except 3 Door) Connectors Terminals
      GTY211345Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Inspect the front passenger switch.

      1. Remove the power window regulator master switch.
      2. Measure the resistance of the switch when the switch is operated.

        Standard resistance

        Window Lock Switch Condition Power Window Switch Condition Tester Connection Specified Condition
        OFF UP 1 (E) - 15 (D)
        6 (B) - 16 (U)        		 Below 1 Ω
        OFF OFF 1 (E) - 16 (U)
        1 (E) - 15 (D)        		 Below 1 Ω
        OFF DOWN 1 (E) - 16 (U)
        6 (B) - 15 (D)        		 Below 1 Ω
        ON UP 1 (E) - 15 (D) 10 kΩ or higher
        6 (B) - 16 (U) Below 1 Ω
        ON OFF 15 (D) - 16 (U) Below 1 Ω
        ON DOWN 1 (E) - 16 (U) 10 kΩ or higher
        6 (B) - 15 (D) Below 1 Ω
      3. Reinstall the power window regulator master switch.

    NG → REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY 

    OK → GO TO POWER WINDOWS DO NOT OPERATE AT ALL  Power Windows do not Operate at All  

scientia non olet · About Mike's Workshop Manuals