Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Toyota >> 2007 >> Tundra Base, 4.7 T, RWD >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System (2UZ-FE) - SFI System Diagnostics Introduction >> SFI System >> Data List / Active Test

Data List / Active Test

  1. DATA LIST 

    HINT:

    Using the intelligent tester or Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
    1. Warm up the engine.
    2. Turn the ignition switch OFF.
    3. Connect the intelligent tester or Techstream to the DLC3.
    4. Turn the ignition switch ON.
    5. Turn the tester ON.
    6. Enter the following menus:
      1. Intelligent tester - Select: DIAGNOSIS / ENHANCED OBD II / DATA LIST /
      2. Techstream - Select: Powertrain / Engine and ECT / Data List /
    7. According to the display on the tester, use the Data List.

      Intelligent tester: 

      DATA LIST (INTELLIGENT TESTER)

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      INJECTOR (PORT) Injection period of the No. 1 cylinder/
      Min.: 0 ms, Max.: 32.64 ms      		 2.0 to 4.0 ms: idling -
      IGN ADVANCE Ignition timing advance for No. 1 cylinder/
      Min.: -64 deg., Max.: 63.5 deg.      		 BTDC5 to 15°:ldling -
      CALCLOAD Calculated load by ECM/
      Min.: 0%, Max.: 100%
      • 11 to 25%: Idling
      • 12 to 26%: Running without load (2500 rpm)
      		 -
      VEHICLE LOAD Vehicle load/
      Min.: 0%, Max.: 25700%      		 Actual vehicle load -
      MAF Air flow rate from Mass Air Flow (MAF) meter/
      Min.: 0 g/sec, Max.: 655 g/sec.      		 4.0 to 8.0 g/sec: Idling If the value approximately 0.0 g/sec.:
      • Mass air flow meter power source circuit open
      • VG circuit open or short if the value 160.0 g/sec. or more:
      • E2G circuit open
      ENGINE SPD Engine speed/
      Min.: 0 rpm, Max.: 16383 rpm      		 650 to 750 rpm: Idling -
      VEHICLE SPD Vehicle speed/
      Min.: 0 km/h, Max.: 255 km/h      		 Actual vehicle speed Speed indicated on speedometer
      COOLANT TEMP Engine coolant temperature/
      Min.: -40°C, Max.: 140°C      		 80 to 100°C (176 to 212°F): After warming up If the value -40°C (-40°F): sensor circuit open
      If the value 140°C (284°F): sensor circuit shorted
      INTAKE AIR Intake air temperature/
      Min.: -40°C, Max.: 140°C      		 Equivalent to ambient air temperature If the value -40°C (-40°F): sensor circuit open
      If the value 140°C (284°F): sensor circuit shorted
      SECONDARY AIR Secondary air system status/
      ON or OFF      		 ON: Secondary air system operation -
      AIR-FUEL RATIO Air fuel ratio/
      Min.: 0, Max.: 1.999      		 0.8 to 1.2: During idling -
      PURGE DENSITY Learning value of purge density/
      Min.: -50, Max.: 350      		 Idling: -40 to 0% Service data
      EVAP PURGE FLOW Purge flow/
      Min.: 0%, Max.: 102.4%      		 0 to 100%: Idling -
      EVAP PURGE VSV Purge VSV control duty/
      Min.: 0%, Max.: 100%      		 0 to 100%: During idling Order signal from ECM
      VAPOR PRES PUMP Vapor pressure/
      Min.: 33.853 kPa, Max.: 125.596 kPa      		 Approximately 100 kPa: Ignition switch ON EVAP system pressure monitored by canister pressure sensor
      VAPOR PRES CALC Calculated EVAP system pressure:
      Min.: -5.632 kPa, Max.: 715.264 kPa      		 Approximately 100 kPa: Ignition switch ON -
      KNOCK CRRT VAL Correction learning value of knocking/
      Min.: -64 CA, Max.: 1984 CA      		 0 to 22° CA:
      Driving, 70 km/h (44 mph)      		 Service data
      KNOCK FB VAL Feedback value of knocking/
      Min.:-64 CA, Max.: 1984 CA      		 -22 to 0° CA:
      Driving, 70 km/h (44 mph)      		 Service data
      CLUTCH Clutch current/
      Min.: 0 A, Max.: 2.49 A      		 - -
      ACCEL POS #1 Absolute Accelerator Pedal Position (APP) No. 1/
      Min.: 0%, Max.: 100%      		 10 to 22%: accelerator pedal is released
      54 to 86%: accelerator pedal is fully depressed      		 -
      ACCEL POS #2 Absolute APP No. 2/
      Min.: 0%, Max.: 100%      		 12 to 42%: accelerator pedal is released
      66 to 98%: accelerator pedal is fully depressed      		 -
      ACCEL POS #1 APP sensor No. 1 voltage/
      Min.: 0 V, Max.: 4.98 V      		 - ETCS freeze data
      ACCEL POS #2 APP sensor No. 2 voltage/
      Min.: 0 V, Max.: 4.98 V      		 - ETCS freeze data
      ACCEL POS #1 APP sensor No. 1 voltage/
      Min.: 0 V, Max.: 5 V      		 0.5 to 1.1 V: accelerator pedal is released
      2.6 to 4.5 V: accelerator pedal is fully depressed      		 -
      ACCEL POS #2 APP sensor No. 2 voltage/
      Min.: 0 V, Max.: 5 V      		 1.2 to 2.0 V: accelerator pedal is released
      3.4 to 5.3 V: accelerator pedal is fully depressed      		 -
      ACCEL IDL POS Whether or not accelerator pedal position sensor detecting idle/
      ON or OFF      		 ON: Idling -
      THRTL LEARN VAL Throttle valve fully closed (learned value) 0.4 to 0.8 V -
      ACCEL SSR #1 AD Accelerator fully closed value No. 1 (AD)/
      Min.: 0, Max.: 4.98 V      		 - ETCS service data
      ACCEL LRN VAL#1 Accelerator fully closed learning value No. 1/
      Min.: 0, Max.: 124.512      		 - ETCS service data
      ACCEL LRN VAL#2 Accelerator fully closed learning value No. 2/
      Min.:0, Max.: 124.512      		 - ETCS service data
      FAIL #1 Whether or not fail-safe function executed/
      ON or OFF      		 ON: ETCS has failed -
      FAIL #2 Whether or not fail-safe function executed/
      ON or OFF      		 ON: ETCS has failed -
      ST1 Brake pedal signal/
      ON or OFF      		 ON: Brake pedal depressed -
      SYS GUARD JUDGE System guard/
      ON or OFF      		 - ETCS service data
      OPN MALFUNCTION Open side malfunction/
      ON or OFF      		 - ETCS service data
      THROTTLE POS Absolute throttle position sensor/
      Min.: 0%, Max.: 100%
      • 10 to 24%: Throttle fully closed
      • 64 to 96%: Throttle fully open
      		 Read the value with intrusive operation (Active Test)
      THROTTLE IDL POS Whether or not throttle position sensor detecting idle/
      ON or OFF      		 ON: Idling -
      THROTTLE REQ POS Throttle requirement position/
      Min.: 0 V, Max.: 5 V      		 0.5 to 1.0 V: Idling -
      THROTTLE POS Throttle sensor positioning/
      Min.: 0%, Max.: 100%      		 10 to 18%: Idling Calculated value based on VTA1
      THROTTLE POS #2 Throttle sensor positioning #2/
      Min.: 0%, Max.: 100%      		 - Calculated value based on VTA2
      THROTTLE POS #1 Throttle position sensor No. 1 output voltage/
      Min.: 0 V, Max.: 4.9 V      		 - ETCS freeze data
      THROTTLE POS #2 Throttle position sensor No. 2 output voltage/
      Min.: 0 V, Max.: 4.9 V      		 - ETCS freeze data
      THROTTLE POS #1 Throttle position No. 1/
      Min.:0V, Max.:5V
      • 0.5 to 1.2 V: Throttle fully closed
      • 3.2 to 4.8 V: Throttle fully open
      		 -
      THROTTLE POS #2 Throttle position No. 2/
      Min.: 0 V, Max.: 5 V
      • 2.0 to 2.9 V: Throttle fully closed
      • 4.6 to 5.5 V: Throttle fully open
      		 Read the value with intrusive operation (Active Test)
      THRTL COMND VAL Throttle position command value/
      Min.: 0 V, Max.: 4.98 V      		 0.5 to 4.8 V ETCS service data
      THROTTLE SSR #1 Throttle sensor opener position No. 1/
      Min.: 0 V, Max.: 4.98 V      		 0.6 to 0.9 V ETCS service data
      THROTTLE SSR #2 Throttle sensor opener position No. 2/
      Min.: 0 V, Max.: 4.98 V      		 2.2 to 2.6 V ETCS service data
      THRTL SSR #1 AD Throttle sensor opener position No. 1 (AD)/
      Min.: 0 V, Max.: 4.98 V      		 0.6 to 0.9 V ETCS service data
      THROTTLE MOT Whether or not throttle actuator control permitted/
      ON or OFF      		 ON: Idling Read the value with the ignition switch ON (Do not start engine)
      THROTTLE MOT Throttle actuator current:
      Min.: 0 A, Max.: 80 A      		 0 to 3.0 A: Idling -
      THROTTLE MOT Throttle actuator/
      Min.: 0%, Max.: 100%      		 0.5 to 40%: Idling -
      THROTTLE MOT Throttle actuator current/
      Min.: 0 A, Max.: 19.92 A      		 0 to 3.0 A: Idling -
      THROTL OPN DUTY Throttle actuator opening duty ratio/
      Min.: 0%, Max.: 100%      		 0 to 40%: During idling When accelerator pedal depressed, duty ratio increased
      THROTL CLS DUTY Throttle actuator closed duty ratio/
      Min.: 0%, Max.: 100%      		 0 to 40%: During idling When accelerator pedal released quickly, duty ratio increased
      THRTL MOT (OPN) Throttle actuator duty ratio (open)/
      Min.: 0%, Max.: 100%      		 - ETCS service data
      THRTL MOT (CLS) Throttle actuator duty ratio (close)/
      Min.: 0%, Max.: 100%      		 - ETCS service data
      O2S B1 S2 Heated oxygen sensor output voltage for bank 1 sensor 2/
      Min.:0V, Max.: 1.275 V      		 0.1 to 0.9 V:
      Driving 44 mph (70 km/h)      		 Performing the INJ VOL or A/F CONTROL function of the ACTIVE TEST enables the technician to check voltage output of the sensor
      O2S B2 S2 Heated oxygen sensor output voltage for bank 2 sensor 2/
      Min.: 0 V, Max.: 1.275 V      		 0.1 to 0.9 V:
      Driving 44 mph (70 km/h)      		 Performing the INJ VOL or A/F CONTROL function of the ACTIVE TEST enables the technician to check voltage output of the sensor
      AFS B1 S1 Air fuel ratio sensor output voltage for bank 1 sensor 1/
      Min.: 0 V, Max.: 7.999 V      		 2.8 to 3.8 V:
      Idling      		 Performing the INJ VOL or A/F CONTROL function of the ACTIVE TEST enables the technician to check voltage output of the sensor
      AFS B2 S1 Air fuel ratio sensor output voltage for bank 2 sensor 1/
      Min.: 0 V, Max.: 7.999 V      		 2.8 to 3.8 V: Idling Performing the INJ VOL or A/F CONTROL function of the ACTIVE TEST enables the technician to check voltage output of the sensor
      AFS B2 S1 Air fuel ratio sensor current for bank 2 sensor 1/
      Min.: 128 mA, Max.: 127.99 mA      		 -0.5 to 0.5 mA: Idling Performing INJ VOL or A/F CONTROL function of ACTIVE TEST enables technician to check output current of sensor
      TOTAL FT #1 Total fuel trim of bank 1 Average value for fuel trim system of bank 1/
      Min.: -0.5 V, Max.: 1496 V      		 -0.2 to 0.2: idling -
      TOTAL FT #2 Total fuel trim of bank 2 Average value for fuel trim system of bank 2/
      Min.:-0.5 V, Max.: 1496 V      		 -0.2 to 0.2: idling -
      SHORT FT #1 Short-term fuel trim of bank 1/
      Min.: -100%, Max.: 99.2%      		 -20 to +20% This item refers to the short-term fuel compensation used to maintain the air fuel ratio at stoichiometric air-fuel ratio
      LONG FT #1 Long-term fuel trim of bank 1/
      Min.: -100%, Max.: 99.2%      		 -20 to +20% This item refers to the overall fuel compensation carried out in long-term to compensate a continual deviation of the short-term fuel trim from the central value
      SHORT FT #2 Short-term fuel trim of bank 2/
      Min.:-100%, Max.: 99.2%      		 -20 to +20% This item refers to the short-term fuel compensation used to maintain the air fuel ratio at stoichiometric air-fuel ratio
      LONG FT #2 Long-term fuel trim of bank 2/
      Min.: -100%, Max.: 99.2%      		 -20 to +20% This item refers to the overall fuel compensation carried out in long-term to compensate a continual deviation of the short-term fuel trim from the central value
      FUEL SYS #1 Fuel system status (bank 1)/
      OL, CL, OL DRIVE, OL FAULT or CL FAULT      		 CL: Idling after warming up
      • OL (Open Loop): Has not yet satisfied conditions to go closed loop
      • CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
      • OL DRIVE: Open loop due to driving conditions (fuel enrichment)
      • OL FAULT: Open loop due to detected system fault
      • CL FAULT: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
      FUEL SYS #2 Fuel system status (bank 2)/
      OL, CL, OL DRIVE, OL FAULT or CL FAULT      		 CL: Idling after warming up
      • OL (Open Loop): Has not yet satisfied conditions to go closed loop
      • CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
      • OL DRIVE: Open loop due to driving conditions (fuel enrichment)
      • OL FAULT: Open loop due to detected system fault
      • CL FAULT: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
      O2 FT B1 S2 Short-term fuel trim associated with the bank 1 sensor 2/
      Min.: -100%, Max.: 99.2%      		 -20 to +20% Same as SHORT FT #1
      O2 FT B2 S2 Short-term fuel trim associated with the bank 2 sensor 2/
      Min.: -100%, Max.: 99.2%      		 -20 to +20% Same as SHORT FT #1
      AF FT B1 S1 Short-term fuel trim associated with the bank 1 sensor 1/
      Min.: 0, Max.: 1.999
      • Value less than 1 (0.000 to 0.999) = Rich
      • Stoichiometric air fuel ratio = 1
      • Value greater than 1 (1.001 to 1.999)= Lean
      		 -
      AFS B1 S1 Air fuel ratio sensor current for bank 1 sensor 1/
      Min.: 128 mA, Max.: 127.99 mA      		 -0.5 to 0.5 mA: Idling Performing INJ VOL or A/F CONTROL function of ACTIVE TEST enables technician to check output current of sensor
      AF FT B2 S1 Short-term fuel trim associated with the bank 2 sensor 1/
      Min.: 0, Max.: 1.999
      • Value less than 1 (0.000 to 0.999) = Rich
      • Stoichiometric air fuel ratio = 1
      • Value greater than 1 (1.001 to 1.999) = Lean
      		 -
      CAT TEMP B1S1 Catalyst temperature (bank 1, sensor 1)/
      Min.:-40°C, Max.: 6513.5°C      		 - -
      CAT TEMP B2S1 Catalyst temperature (bank 2, sensor 1)/
      Min.: -40°C, Max.: 6513.5°C      		 - -
      CAT TEMP B1S2 Catalyst temperature (bank 1, sensor 2)/
      Min.:-40°C, Max.: 6513.5°C      		 - -
      CAT TEMP B2S2 Catalyst temperature (bank 2, sensor 2)/
      Min.: -40°C, Max.: 6513.5°C      		 - -
      SO2SB1S2 Sub heated oxygen sensor Impedance (bank 1 sensor 2)/
      Min.: 0Ω, Max.: 21247.68Ω      		 5 to 15000Ω After driving approx. 10 min. in urban area
      S O2S B2S2 Sub heated oxygen sensor impedance (bank 2 sensor 2)/
      Min.: 0 Ω, Max.: 21247.68 Ω      		 5 to 15000 Ω After driving approx. 10 min. in urban area
      INI COOL TEMP Initial engine coolant temperature/
      Min.: -40°C, Max.: 140°C      		 Close to ambient air temperature Service data
      INI INTAKE TEMP Initial intake air temperature/
      Min.: -40°C, Max.: 140°C      		 Close to ambient air temperature Service data
      INJ VOL Injection volume (cylinder 1)/
      Min.: 0 ml, Max.: 2.048 ml      		 0 to 0.5 ml Quantity of fuel injection volume for 10 times
      AIR PMP PRS (A) Air pump pressure (absolute)/
      Min.: 0 kPa, Max.: 320 kPa      		 Atmospheric pressure +1 kPa or more: Air pump ON, Air switching valve open Close to atmospheric pressure: Air pump OFF, Air switching valve close Refer to DTC P2431
      AIR PMP PLS PRS Air pump pulsation pressure/
      Min.: 0 kPa, Max.: 639.9 kPa      		 -
      AIR PMP2 PRS (A) Air pump pressure (absolute)/
      Min.: 0 kPa, Max.: 320 kPa      		 Atmospheric pressure +1 kPa or more: Air pump ON, Air switching valve open
      Close to atmospheric pressure: Air pump OFF, Air switching valve close      		 Refer to DTC P2431
      AIR PMP2 PULSE Air pump pulsation pressure/
      Min.: 0 kPa, Max.: 639.9 kPa      		 -
      PWR ST PRESSURE Power steering oil pressure/
      Min.: -1.897 MPa, Max.: 12.799 MPa      		 - -
      ACC RELAY Ace relay status/
      ON or OFF      		 ON: Cranking -
      STARTER RELAY Starter relay status/
      ON or OFF      		 ON: Cranking -
      STARTER SIG Starter signal/
      ON or OFF      		 ON: Cranking -
      STARTER CONTROL Starter switch status/
      ON or OFF      		 ON: Cranking -
      CTPSW Closed throttle position switch/
      ON or OFF
      • ON: Throttle fully closed
      • OFF: Throttle open
      		 -
      A/C SIGNAL A/C switch status/
      ON or OFF      		 ON: A/C ON -
      PNP SW [NSW] PNP switch status/
      ON or OFF      		 ON: P or N position -
      ELECT LOAD SIG Electrical load signal/
      ON or OFF      		 ON: Headlights or defogger is turned ON -
      STOP LIGHT SW Stop light switch/
      ON or OFF      		 ON: Brake pedal is depressed -
      IMMOBI COMM Immobiliser communication/
      ON or OFF      		 ON: Normal -
      FUEL CUT COND Fuel cut condition/
      ON or OFF      		 ON: Fuel cut operating -
      +BM Whether or not electric throttle control system power inputted/
      ON or OFF      		 ON: Idling -
      +BM VOLTAGE +BM voltage/
      Min.: 0, Max.: 19.92      		 10 to 15 V: Idling ETCS service data
      BATTERY VOLTAGE Battery voltage/
      Min.: 0 V, Max.: 65535 V      		 11 to 14 V: Idling -
      ACTUATOR POWER Actuator power supply/
      ON or OFF      		 ON: Idling ETCS service data
      ATM PRESSURE Atmospheric pressure/
      Min.:0kPa, Max.:150kPa      		 Equivalent to atmospheric pressure (absolute pressure) -
      SECOND AIR VSV Secondary air injection system status ON: Secondary air injection system operation -
      ACIS VSV VSV status for ACIS control/ ON or OFF - Active Test support data
      ACT VSV A/C cut status for Active Test/ ON or OFF - Active Test support data
      VVT CTRL B2 VVT control status (bank 2)1 ON or OFF - Active Test support data
      EVAP (Purge) VSV VSV status for EVAP control/
      ON or OFF      		 - Active Test support data
      FUEL PUMP/SPD Fuel pump/speed status/
      ON or OFF      		 - Active Test support data
      VVT CTRL B1 Variable valve timing (VVT) control status (bank 1)/
      ON or OFF      		 - Active Test support data
      VACUUM PUMP Key-off EVAP system pump status/
      ON or OFF      		 - Active Test support data
      EVAP VENT VAL Key-off EVAP system vent valve status/
      ON or OFF      		 - Active Test support data
      TC/TE1 TC and TE1 terminal of DLC3/
      ON or OFF      		 - -
      Al TEST Al operation prohibition/
      OK or NG      		 OK -
      VVTL AIM ANGL #1 VVT aim angle (bank 1)/
      Min.: 0%, Max.: 100%      		 0%: Idling VVT duty signal value during intrusive operation
      VVTL CHAG ANGL #1 VVT change angle (bank 1)/
      Min.: 0° FR, Max.: 60° FR      		 0 to 5° FR: Idling Displacement angle during intrusive operation
      VVT OCV DUTY B1 VVT OCV operation duty (bank 1)/
      Min.: 0%, Max.: 100%      		 0%: Idling Requested duty value for intrusive operation
      VVTL AIM ANGL #2 VVT aim angle (bank 2)/
      Min.: 0%, Max.: 100%      		 0%: Idling VVT duty signal value during intrusive operation
      VVT CHNG ANGL #2 VVT change angle (bank 2)/
      Min.: 0° FR, Max.: 60° FR      		 0 to 5° FR: Idling Displacement angle during intrusive operation
      VVT OCV DUTY B2 VVT OCV operation duty (bank 2)/
      Min.: 0%, Max.: 100%      		 0%: Idling Requested duty value for intrusive operation
      FCIDL Fuel cut idle/
      ON or OFF      		 ON: Fuel cut operation FC IDL = "ON" when throttle valve fully closed and engine speed over 2800 rpm
      FC TAU Fuel cut TAU: Fuel cut during very light load/
      ON or OFF      		 ON: Fuel cut operation The fuel cut being performed under very light load to prevent the engine combustion from becoming incomplete
      IGNITION Ignition counter/
      Min.: 0, Max.: 800      		 0 to 800 -
      CYL#1,#2,#3,#4,#5, #6, #7, #8 Misfire ratio of the cylinder 1 to 8/
      Min.: 0, Max.: 255      		 0% This item displayed only when idling engine
      CYL ALL All cylinders misfire rate/
      Min.: 0, Max.: 255      		 0 to 35 -
      CYLS Multiple cylinder misfire rate/
      Min.: 0 Max.:65535      		 0 to 65535 -
      MISFIRE RPM Engine RPM for first misfire range/
      Min.: 0 rpm, Max.: 6375 rpm      		 0 rpm: Misfire 0 -
      MISFIRE LOAD Engine load for first misfire range/
      Min.: 0 g/rev, Max.: 3.98 g/rev      		 0 g/rev: Misfire 0 -
      MISFIRE MARGIN Misfire monitoring/
      Min.:-100%, Max.: 99.22%      		 -100 to 99.2% Misfire detecting margin
      CAT OT MF F/C Catalyst over temperature misfire prevention F/C/
      0:NOTAVL, 1: AVAIL      		 AVAIL: CAT OT FC available
      NOT AVL: CAT OT FC not available      		 Service data
      CAT OT FC HSTRY Catalyst over temperature misfire prevention F/C history/
      0:OFF, 1:ON      		 ON: Fuel cut operation history exists Service data
      #CODES #Codes/
      Min.: 0, Max.: 255      		 - Number of detected DTCs
      CHECK MODE Check mode/
      0:ON, 1:OFF      		 ON: Check mode ON Refer to CHECK MODE PROCEDURE 
      AS TEST Check mode result for secondary air injection system/
      0:COMPL, 1:INCOMPL      		 - -
      MISFIRE TEST Check mode result for misfire monitor/
      0:COMPL, 1:INCOMPL      		 - -
      OXS2 TEST Check mode result for heated oxygen sensor (bank 2)/
      0:COMPL, 1:INCOMPL      		 - -
      OXS1 TEST Check mode result for heated oxygen sensor (bank 1)/
      0:COMPL, 1:INCOMPL      		 - -
      A/F SSR TEST B2 Check mode result for air fuel ratio sensor (bank 2)/
      0:COMPL,1:INCOMPL      		 - -
      A/F SSR TEST B1 Check mode result for air fuel ratio sensor (bank 1)/
      0:COMPL, 1:INCOMPL      		 - -
      MIL MIL status/
      ON or OFF      		 ON: MIL ON -
      MIL ON RUN DIST MIL ON run distance/
      Min.: 0 km, Max.: 65535 km      		 Distance after DTC detected -
      MIL ON RUN TIME Running time from MIL ON/
      Min.: 0 minute, Max.: 65535 minutes      		 Equivalent to running time after MIL was ON -
      ENG RUN TIME Engine run time/
      Min.: 0 seconds, Max.: 65535 seconds      		 Time after engine start Service data
      TIME DTC CLEAR Time after DTC cleared/
      Min.: 0 minutes, Max.: 65535 minutes      		 Equivalent to time after DTCs were erased -
      DIST DTC CLEAR Distance after DTC cleared/
      Min.: 0 km, Max.: 65535 km      		 Equivalent to drive distance after DTCs were erased -
      WU CYC DTCCLEAR Warm-up cycle after DTC cleared/
      Min.: 0, Max.: 255      		 - Number of warm-up cycles after DTC cleared
      OBD CERT OBD requirement OBD2 -
      #CARB CODES Emission related DTCs - Number of emission related DTCs
      COMP MON Comprehensive component monitor/
      NOT AVL or AVAIL      		 - -
      FUEL MON Fuel system monitor/
      NOT AVL or AVAIL      		 - -
      MISFIRE MON Misfire monitor/
      NOT AVL or AVAIL      		 - -
      O2S (A/FS) HTR O2S (A/FS) heater monitor/
      NOT AVL or AVAIL      		 - -
      O2S (A/FS) HTR O2S (A/FS) heater monitor/
      COMPL or INCMPL      		 - -
      O2S (A/FS) MON O2S (A/FS) monitor/
      NOT AVL or AVAIL      		 - -
      O2S (A/FS) MON O2S (A/FS) monitor/
      COMPL or INCMPL      		 - -
      2nd AIR MON 2nd air monitor/
      NOT AVL or AVAIL      		 - -
      2nd AIR MON 2nd air monitor/
      COMPL or INCMPL      		 - -
      EVAP MON EVAP monitor/
      NOT AVL or AVAIL      		 - -
      EVAP MON EVAP monitor/
      COMPL or INCMPL      		 - -
      CAT MON Catalyst monitor/
      NOT AVL or AVAIL      		 - -
      CAT MON Catalyst monitor/
      COMPL or INCMPL      		 - -
      CCM ENA Comprehensive component monitor/
      UNABLE or ENABLE      		 - -
      CCM CMPL Comprehensive component monitor/
      COMPL or INCMPL      		 - -
      FUEL ENA Fuel system monitor/
      UNABLE or ENABLE      		 - -
      FUEL CMPL Fuel system monitor/
      COMPL or INCMPL      		 - -
      MISFIRE ENA Misfire monitor/
      UNABLE or ENABLE      		 - -
      MISFIRE CMPL Misfire monitor/
      COMPL or INCMPL      		 - -
      HTR ENA O2S (A/FS) heater monitor/
      UNABLE or ENABLE      		 - -
      HTR CMPL O2S (A/FS) heater monitor/
      COMPL or INCMPL      		 - -
      O2S (A/FS) ENA O2S (A/FS) monitor/
      UNABLE or ENABLE      		 - -
      O2S (A/FS) CMPL O2S (A/FS) monitor/
      COMPL or INCMPL      		 - -
      AIR ENA 2nd air monitor/
      UNABLE or ENABLE      		 - -
      AIR CMPL 2nd air monitor/
      COMPL or INCMPL      		 - -
      EVAP ENA EVAP monitor/
      UNABLE or ENABLE      		 - -
      EVAP CMPL EVAP monitor/
      COMPL or INCMPL      		 - -
      CAT ENA Catalyst monitor/
      UNABLE or ENABLE      		 - -
      CAT CMPL Catalyst monitor/
      COMPL or INCMPL      		 - -
      MODEL CODE Model code - Identifying the model code: UCK5##
      ENGINE TYPE Engine type - Identifying the engine type: 2UZFE
      CYLINDER NUMBER Cylinder number/
      Min.: 0, Max.: 255      		 - Identifying the cylinder number: 8
      TRANSMISSION Transmission type - Identifying the transmission type: ECT (5AT)
      DESTINATION Destination - Identifying the destination: A (America)
      MODEL YEAR Model year/
      Min.: 0, Max.: 255      		 - Identifying the model year: 200#
      SYSTEM System identification - Identifying the engine system: GASLIN (gasoline engine)

      Techstream: 

      DATA LIST (TECHSTREAM)

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Injector (Port) Injection period of the No. 1 cylinder/
      Min.: 0 ms, Max.: 32.64 ms      		 2.0 to 4.0 ms: idling -
      IGN Advance Ignition timing advance for No. 1 cylinder/
      Min.: -64 deg., Max.: 63.5 deg.      		 BTDC 5 to 15°:ldling -
      Calculate Load Calculated load by ECM/
      Min.: 0%, Max.: 100%
      • 11 to 25%: Idling
      • 12 to 26%: Running without load (2500 rpm)
      		 -
      Vehicle Load Vehicle load/
      Min.: 0%, Max.: 25700%      		 Actual vehicle load -
      MAF Air flow rate from Mass Air Flow (MAF) meter/
      Min.: 0 g/sec, Max.: 655 g/sec.      		 4.0 to 8.0 g/sec: Idling If the value approximately 0.0 g/sec:
      • Mass air flow meter power source circuit open
      • VG circuit open or short if the value 160.0 g/sec. or more:
      • E2G circuit open
      Engine Speed Engine speed/
      Min.: 0 rpm, Max.: 16383 rpm      		 650 to 750 rpm: Idling -
      Vehicle Speed Vehicle speed/
      Min.: 0 km/h, Max.: 255 km/h      		 Actual vehicle speed Speed indicated on speedometer
      Coolant Temp Engine coolant temperature:
      Min.: -40°C, Max.: 140°C      		 80 to 100°C (176 to 212°F): After warming up If the value -40°C (-40°F): sensor circuit open
      If the value 140°C (284°F): sensor circuit shorted
      Intake Air Intake air temperature/
      Min.: -40°C, Max.: 140°C      		 Equivalent to ambient air temperature If the value -40°C (-40°F): sensor circuit open
      If the value 140°C (284°F): sensor circuit shorted
      2nd Air System Status Secondary air system status/
      ON or OFF      		 ON: Secondary air system operation -
      Air-Fuel Ratio Air fuel ratio:
      Min.: 0, Max.: 1.999      		 0.8 to 1.2: During idling -
      Purge Density Learn Value Learning value of purge density/
      Min.: -50, Max.: 350      		 Idling: -40 to 0% Service data
      Evap Purge Flow Purge flow/
      Min.: 0%, Max.: 102.4%      		 0 to 100%: Idling -
      EVAP (Purge) VSV Purge VSV control duty/
      Min.: 0%, Max.: 100%      		 0 to 100%: During idling Order signal from ECM
      Vapor Pressure Pump Vapor pressure/
      Min.: 33.853 kPa, Max.: 125.596 kPa      		 Approximately 100 kPa: Ignition switch ON EVAP system pressure monitored by canister pressure sensor
      Vapor Pressure (Calculated) Calculated EVAP system pressure/
      Min.: -5.632 kPa, Max.: 715.264 kPa      		 Approximately 100 kPa: Ignition switch ON -
      Knock Correct Learn Value Correction learning value of knocking/
      Min.:-64 CA, Max.: 1984 CA      		 0 to 22° CA: Driving, 70 km/h (44 mph) Service data
      Knock Feedback Value Feedback value of knocking/
      Min.: -64 CA, Max.: 1984 CA      		 -22 to 0° CA:
      Driving, 70 km/h (44 mph)      		 Service data
      Clutch Current Clutch current/
      Min.: 0 A, Max.: 2.49 A      		 - -
      Accelerator Position No.1 Absolute Accelerator Pedal Position (APP) No. 1/
      Min.: 0%, Max.: 100%      		 10 to 22%: accelerator pedal is released
      54 to 86%: accelerator pedal is fully depressed      		 -
      Accelerator Position No.2 Absolute APP No. 2/
      Min.: 0%, Max.: 100%      		 12 to 42%: accelerator pedal is released
      66 to 98%: accelerator pedal is fully depressed      		 -
      Accelerator Position No.1 APP sensor No. 1 voltage/
      Min.: 0 V, Max.: 4.98 V      		 - ETCS freeze data
      Accelerator Position No.2 APP sensor No. 2 voltage/
      Min.: 0 V, Max.: 4.98 V      		 - ETCS freeze data
      Accelerator Position No.1 APP sensor No. 1 voltage/
      Min.: 0 V, Max.: 5 V      		 0.5 to 1.1 V: accelerator pedal is released
      2.6 to 4.5 V: accelerator pedal is fully depressed      		 -
      Accelerator Position No.2 APP sensor No. 2 voltage/
      Min.: 0 V, Max.: 5 V      		 1.2 to 2.0 V: accelerator pedal is released
      3.4 to 5.3 V: accelerator pedal is fully depressed      		 -
      Accelerator Idle Position Whether or not accelerator pedal position sensor detecting idle/
      ON or OFF      		 ON: Idling -
      Throttle Fully Close Learn Throttle valve fully closed (learned value) 0.4 to 0.8 V -
      Accel Fully Close #1 (AD) Accelerator fully closed value No. 1 (AD)/
      Min.: 0, Max.: 4.98 V      		 - ETCS service data
      Accel Fully Close Learn #1 Accelerator fully closed learning value No. 1/
      Min.: 0, Max.: 124.512      		 - ETCS service data
      Accel Fully Close Learn #2 Accelerator fully closed learning value No. 2/
      Min.: 0, Max.: 124.512      		 - ETCS service data
      Fail Safe Drive Whether or not fail-safe function executed/
      ON or OFF      		 ON: ETCS has failed -
      Fail Safe Drive (Main CPU) Whether or not fail-safe function executed/
      ON or OFF      		 ON: ETCS has failed -
      ST1 Brake pedal signal/
      ON or OFF      		 ON: Brake pedal depressed -
      System Guard System guard/
      ON or OFF      		 - ETCS service data
      Open Side Malfunction Open side malfunction/
      ON or OFF      		 - ETCS service data
      Throttle Position Absolute throttle position sensor/
      Min.: 0%, Max.: 100%
      • 10 to 24%: Throttle fully closed
      • 64 to 96%: Throttle fully open
      		 Read the value with intrusive operation (Active Test)
      Throttle Idle Position Whether or not throttle position sensor detecting idle/
      ON or OFF      		 ON: Idling -
      Throttle Require Position Throttle requirement position/
      Min.: 0 V, Max.: 5 V      		 0.5 to 1.0 V: Idling -
      Throttle Sensor Position Throttle sensor positioning/
      Min.: 0%, Max.: 100%      		 10 to 18%: Idling Calculated value based on VTA1
      Throttle Sensor Position #2 Throttle sensor positioning #2/
      Min.: 0%, Max.: 100%      		 - Calculated value based on VTA2
      Throttle Position No.1 Throttle position sensor No. 1 output voltage/
      Min.: 0 V, Max.: 4.9 V      		 - ETCS freeze data
      Throttle Position No.2 Throttle position sensor No. 2 output voltage/
      Min.: 0 V, Max.: 4.9 V      		 - ETCS freeze data
      Throttle Position No.1 Throttle position No. 1/
      Min.: 0 V, Max.: 5 V
      • 0.5 to 1.2 V: Throttle fully closed
      • 3.2 to 4.8 V: Throttle fully open
      		 -
      Throttle Position No.2 Throttle position No. 2/
      Min.: 0 V, Max.: 5 V
      • 2.0 to 2.9 V: Throttle fully closed
      • 4.6 to 5.5 V: Throttle fully open
      		 Read the value with intrusive operation (Active Test)
      Throttle Position Command Throttle position command value/
      Min.: 0 V, Max.: 4.98 V      		 0.5 to 4.8 V ETCS service data
      Throttle Sens Open Pos#1 Throttle sensor opener position No. 1/
      Min.: 0 V, Max.: 4.98 V      		 0.6 to 0.9 V ETCS service data
      Throttle Sens Open Pos#2 Throttle sensor opener position No. 2/
      Min.: 0 V, Max.: 4.98 V      		 2.2 to 2.6 V ETCS service data
      Throttle Sens Open #1 (AD) Throttle sensor opener position No. 1 (AD)/
      Min.: 0 V, Max.: 4.98 V      		 0.6 to 0.9 V ETCS service data
      Throttle Motor Whether or not throttle actuator control permitted/
      ON or OFF      		 ON: Idling Read the value with the ignition switch ON (Do not start engine)
      Throttle Motor Current Throttle actuator current/
      Min.: 0 A, Max.: 80 A      		 0 to 3.0 A: Idling -
      Throttle Motor Throttle actuator/
      Min.: 0%, Max.: 100%      		 0.5 to 40%: Idling -
      Throttle Motor Current Throttle actuator current/
      Min.: 0 A, Max.: 19.92 A      		 0 to 3.0 A: Idling -
      Throttle Motor Open Duty Throttle actuator opening duty ratio/
      Min.: 0%, Max.: 100%      		 0 to 40%: During idling When accelerator pedal depressed, duty ratio increased
      Throttle Motor Close Duty Throttle actuator closed duty ratio/
      Min.: 0%, Max.: 100%      		 0 to 40%: During idling When accelerator pedal released quickly, duty ratio increased
      Throttle Motor Duty (Open) Throttle actuator duty ratio (open)/
      Min.: 0%, Max.: 100%      		 - ETCS service data
      Throttle Motor Duty (Close) Throttle actuator duty ratio (close)/
      Min.: 0%, Max.: 100%      		 - ETCS service data
      O2S B1 S2 Heated oxygen sensor output voltage for bank 1 sensor 2/
      Min.:0V, Max.: 1.275 V      		 0.1 to 0.9 V:
      Driving 44 mph (70 km/h)      		 Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor
      O2S B2 S2 Heated oxygen sensor output voltage for bank 2 sensor 2/
      Min.: 0 V, Max.: 1.275 V      		 0.1 to 0.9 V: Driving 44 mph (70 km/h) Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor
      AFS B1 S1 Air fuel ratio sensor output voltage for bank 1 sensor 1/
      Min.: 0 V, Max.: 7.999 V      		 2.8 to 3.8 V: Idling Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor
      AFS B2 S1 Air fuel ratio sensor output voltage for bank 2 sensor 1/
      Min.: 0 V, Max.: 7.999 V      		 2.8 to 3.8 V: Idling Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor
      AFS B2 S1 Air fuel ratio sensor current for bank 2 sensor 1/
      Min.: 128 mA, Max.: 127.99 mA      		 -0.5 to 0.5 mA: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output current of sensor
      Total FT #1 Total fuel trim of bank 1
      Average value for fuel trim system of bank 1/
      Min.:-0.5 V, Max.: 1496 V      		 -0.2 to 0.2: Idling -
      Total FT #2 Total fuel trim of bank 2
      Average value for fuel trim system of bank 2/
      Min.:-0.5 V, Max.: 1496 V      		 -0.2 to 0.2: Idling -
      Short FT #1 Short-term fuel trim of bank 1/
      Min.:-100%, Max.: 99.2%      		 -20 to +20% This item refers to the short-term fuel compensation used to maintain the air fuel ratio at stoichiometric air-fuel ratio
      Long FT #1 Long-term fuel trim of bank 1/
      Min.: -100%, Max.: 99.2%      		 -20 to +20% This item refers to the overall fuel compensation carried out in long-term to compensate a continual deviation of the short-term fuel trim from the central value
      Short FT #2 Short-term fuel trim of bank 2/
      Min.:-100%, Max.: 99.2%      		 -20 to +20% This item refers to the short-term fuel compensation used to maintain the air fuel ratio at stoichiometric air-fuel ratio
      Long FT #2 Long-term fuel trim of bank 2/
      Min.: -100%, Max.: 99.2%      		 -20 to +20% This item refers to the overall fuel compensation carried out in long-term to compensate a continual deviation of the short-term fuel trim from the central value
      Fuel System Status (Bank1) Fuel system status (bank 1)/
      OL, CL, OL Drive, OL Fault or CL Fault      		 CL: Idling after warming up
      • OL (Open Loop): Has not yet satisfied conditions to go closed loop
      • CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
      • OL Drive: Open loop due to driving conditions (fuel enrichment)
      • OL Fault: Open loop due to detected system fault
      • CL Fault: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
      Fuel System Status (Bank2) Fuel system status (bank 2)/
      OL, CL, OL Drive, OL Fault or CL Fault      		 CL: Idling after warming up
      • OL (Open Loop): Has not yet satisfied conditions to go closed loop
      • CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
      • OL Drive: Open loop due to driving conditions (fuel enrichment)
      • OL Fault: Open loop due to detected system fault
      • CL Fault: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
      AF FT B1 S1 Short-term fuel trim associated with the bank 1 sensor 1/
      Min.:0, Max.: 1.999
      • Value less than 1 (0.000 to 0.999) = Rich
      • Stoichiometric air fuel ratio = 1 Value greater than 1 (1.001 to 1.999) = Lean
      		 -
      AFS B1 S1 Air fuel ratio sensor current bank 1 sensor 1/
      Min.: 128 mA, Max.: 127.99 mA      		 -0.5 to 0.5 mA: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output current of sensor
      AF FT B2 S1 Short-term fuel trim associated with the bank 2 sensor 1/
      Min.: 0, Max.: 1.999
      • Value less than 1 (0.000 to 0.999) = Rich
      • Stoichiometric air fuel ratio = 1
      • Value greater than 1 (1.001 to 1.999) = Lean
      		 -
      Catalyst Temp (B1S1) Catalyst temperature (bank 1, sensor 1)/
      Min.:-40°C, Max.: 6513.5°C      		 - -
      Catalyst Temp (B2S1) Catalyst temperature (bank 2, sensor 1)/
      Min.:-40°C, Max.: 6513.5°C      		 - -
      Catalyst Temp (B1S2) Catalyst temperature (bank 1, sensor 2)/
      Min.: -40°C, Max.: 6513.5°C      		 - -
      Catalyst Temp (B2 S2) Catalyst temperature (bank 2, sensor 2)/
      Min.: -40°C, Max.: 6513.5°C      		 - -
      Sub O2S Impedance B1S2 Sub heated oxygen sensor impedance (bank 1 sensor 2)/
      Min.: 0 Ω, Max.: 21247.68 Ω      		 5 to 15000 Ω After driving approx. 10 min. in urban area
      Sub O2S Impedance B2S2 Sub heated oxygen sensor impedance (bank 2 sensor 2)/
      Min.: 0 Ω, Max.: 21247.68 Ω      		 5 to 15000 Ω After driving approx. 10 min. in urban area
      Initial Engine Coolant Temp Initial engine coolant temperature/
      Min.: -40°C, Max.: 140°C      		 Close to ambient air temperature Service data
      Initial Intake Air Temp Initial intake air temperature/
      Min.: -40°C, Max.: 140°C      		 Close to ambient air temperature Service data
      Injection Volume (Cylinder 1) Injection volume (cylinder 1)/
      Min.: 0 ml, Max.: 2.048 ml      		 0 to 0.5 ml Quantity of fuel injection volume for 10 times
      Air pump pressure (absolute) Air pump pressure (absolute)/
      Min.: 0 kPa, Max.: 320 kPa      		 Atmospheric pressure +1 kPa or more: Air pump ON, Air switching valve open
      Close to atmospheric pressure: Air pump OFF, Air switching valve close      		 Refer to DTC P2431
      Air Pump Pulsation Pressure Air pump pulsation pressure/
      Min.: 0 kPa, Max.: 639.9 kPa      		 -
      Air Pump2 Pressure (Absolute) Air pump pressure (absolute)/
      Min.: 0 kPa, Max.: 320 kPa      		 Atmospheric pressure +1 kPa or more: Air pump ON, Air switching valve open
      Close to atmospheric pressure: Air pump OFF, Air switching valve close      		 Refer to DTC P2431
      Air Pump2 Pulsation Pressure Air pump pulsation pressure/
      Min.: 0 kPa, Max.: 639.9 kPa      		 -
      Power Steering Pressure Power steering oil pressure/
      Min.: -1.897 MPa, Max.: 12.799 MPa      		 - -
      ACC Relay Ace relay status/
      ON or OFF      		 ON: Cranking -
      Starter Relay Starter relay status/
      ON or OFF      		 ON: Cranking -
      Starter Signal Starter signal/
      ON or OFF      		 ON: Cranking -
      Starter Control Starter switch status/
      ON or OFF      		 ON: Cranking -
      Closed Throttle Position SW Closed throttle position switch/
      ON or OFF
      • ON: Throttle fully closed
      • OFF: Throttle open
      		 -
      A/C Signal A/C switch status/
      ON or OFF      		 ON: A/C ON -
      Neutral Position SW Signal PNP switch status/
      ON or OFF      		 ON: P or N position -
      Electrical Load Signal Electrical load signal/
      ON or OFF      		 ON: Headlights or defogger is turned ON -
      Stop Light Switch Stop light switch/
      ON or OFF      		 ON: Brake pedal is depressed -
      Immobiliser Communication Immobiliser communication/
      ON or OFF      		 ON: Normal -
      Fuel Cut Condition Fuel cut condition/
      ON or OFF      		 ON: Fuel cut operating -
      ETCS Actuator Power Whether or not electric throttle control system power inputted/
      ON or OFF      		 ON: Idling -
      +BM Voltage +BM voltage/
      Min.: 0, Max.: 19.92      		 10 to 15 V: Idling ETCS service data
      Battery Voltage Battery voltage/
      Min.: 0 V, Max.: 65535 V      		 11 to 14 V: Idling -
      Actuator Power Supply Actuator power supply/
      ON or OFF      		 ON: Idling ETCS service data
      Atmosphere Pressure Atmospheric pressure/
      Min.:0kPa, Max.:150kPa      		 Equivalent to atmospheric pressure (absolute pressure) -
      Secondary Air Control VSV Secondary air injection system status ON: Secondary air injection system operation -
      ACIS VSV VSV status for ACIS control/
      ON or OFF      		 - Active Test support data
      ACT VSV A/C cut status for Active Test/
      ON or OFF      		 - Active Test support data
      VVT Control Status (Bank2) VVT control status (bank 2)/
      ON or OFF      		 - Active Test support data
      EVAP Purge VSV VSV status for EVAP control/
      ON or OFF      		 - Active Test support data
      Fuel Pump/Speed Status Fuel pump/speed status/
      ON or OFF      		 - Active Test support data
      VVT Control Status (Bank1) Variable valve timing (VVT) control status (bank 1)/
      ON or OFF      		 - Active Test support data
      Vacuum Pump Key-off EVAP system pump status/
      ON or OFF      		 - Active Test support data
      EVAP System Vent Value Key-off EVAP system vent valve status/
      ON or OFF      		 - Active Test support data
      TC and TE1 TC and TE1 terminal of DLC3/
      ON or OFF      		 - -
      Al Test Al operation prohibition/
      OK or NG      		 OK -
      VVT Aim Angle (Bank1) VVT aim angle (bank 1)/
      Min.: 0%, Max.: 100%      		 0%: Idling VVT duty signal value during intrusive operation
      VVT Change Angle (Bank1) VVT change angle (bank 1)/
      Min.: 0° FR, Max.: 60° FR      		 0 to 5° FR: Idling Displacement angle during intrusive operation
      VVT OCV Duty (Bank1) VVT OCV operation duty (bank 1)/
      Min.: 0%, Max.: 100%      		 0%: Idling Requested duty value for intrusive operation
      VVT Aim Angle (Bank2) VVT aim angle (bank 2)/
      Min.: 0%, Max.: 100%      		 0%: Idling VVT duty signal value during intrusive operation
      VVT Change Angle (Bank2) VVT change angle (bank 2)/
      Min.: 0° FR, Max.: 60° FR      		 0 to 5° FR: Idling Displacement angle during intrusive operation
      VVT OCV Duty (Bank2) VVT OCV operation duty (bank 2)/
      Min.: 0%, Max.: 100%      		 0%: Idling Requested duty value for intrusive operation
      Idle Fuel Cut Fuel cut idle/
      ON or OFF      		 ON: Fuel cut operation Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2800 rpm
      FC TAU Fuel cut TAU: Fuel cut during very light load/
      ON or OFF      		 ON: Fuel cut operation The fuel cut being performed under very light load to prevent the engine combustion from becoming incomplete
      Ignition Ignition counter/
      Min.: 0, Max.: 800      		 0 to 800 -
      Cylinder #1 Misfire Count to Cylinder #8 Misfire Count Misfire ratio of the cylinder 1 to 8/
      Min.: 0, Max.: 255      		 0% This item displayed only when idling engine
      All Cylinders Misfire Count All cylinders misfire rate/
      Min.: 0, Max.: 255      		 0 to 35 -
      Multi Cylinders Misfire Count Multiple cylinder misfire rate/
      Min.: 0 Max.:65535      		 0 to 65535 -
      Misfire RPM Engine RPM for first misfire range/
      Min.: 0 rpm, Max.: 6375 rpm      		 0 rpm: Misfire 0 -
      Misfire Load Engine load for first misfire range/
      Min.: 0 g/rev, Max.: 3.98 g/rev      		 0 g/rev: Misfire 0 -
      Misfire Margin Misfire monitoring/
      Min.: -100%, Max.: 99.22%      		 -100 to 99.2% Misfire detecting margin
      Catalyst OT MF F/C Catalyst over temperature misfire prevention F/C/
      0:Not Avl, 1: Avail      		 Avail: Cat OT MF F/C available
      Not Avl: Cat OT MF F/C not available      		 -
      Cat OT MF F/C History Catalyst over temperature misfire prevention F/C history/
      0:OFF, 1:ON      		 ON: Fuel cut operation history exists -
      # Codes #Codes/
      Min.: 0, Max.: 255      		 - Number of detected DTCs
      Check Mode Check mode/
      0:ON,1:OFF      		 ON: Check mode ON Refer to CHECK MODE PROCEDURE 
      SPD TEST Check mode result for vehicle speed sensor/
      COMPL or INCMPL      		 - -
      AS Test Check mode result for secondary air injection system/
      0: Compl, 1: Incmpl      		 - -
      Misfire Test Check mode result for misfire monitor/
      0: Compl, 1: Incmpl      		 - -
      OXS2 Test Check mode result for heated oxygen sensor (bank 2)/
      0: Compl, 1: Incmpl      		 - -
      OXS1 Test Check mode result for heated oxygen sensor (bank 1)/
      0: Compl, 1: Incmpl      		 - -
      A/F Test Results (Bank2) Check mode result for air fuel ratio sensor (bank 2)/
      0: Compl, 1: Incmpl      		 - -
      A/F Test Results (Bank1) Check mode result for air fuel ratio sensor (bank 1)/
      0: Compl, 1: Incmpl      		 - -
      MIL MIL status/
      ON or OFF      		 ON: MIL ON -
      MIL ON Run Distance MIL ON run distance/
      Min.: 0 km, Max.: 65535 km      		 Distance after DTC detected -
      Running Time from MIL ON Running time from MIL ON/
      Min.: 0 minute, Max.: 65535 minutes      		 Equivalent to running time after MIL was ON -
      Engine Run Time Engine run time/
      Min.: 0 seconds, Max.: 65535 seconds      		 Time after engine start Service data
      Time after DTC Cleared Time after DTC cleared/
      Min.: 0 minutes, Max.: 65535 minutes      		 Equivalent to time after DTCs were erased -
      Distance from DTC Cleared Distance after DTC cleared/
      Min.: 0 km, Max.: 65535 km      		 Equivalent to drive distance after DTCs were erased -
      Warm-up Cycle Clear DTC Warm-up cycle after DTC cleared/
      Min.: 0, Max.: 255      		 - Number of warm-up cycles after DTC cleared
      OBD Requirements OBD requirement OBD2 -
      Number of Emission DTC Emission related DTCs - Number of emission related DTCs
      Complete Parts Monitor Comprehensive component monitor/
      Not Avl or Avail      		 - -
      Fuel System Monitor Fuel system monitor/
      Not Avl or Avail      		 - -
      Misfire Monitor Misfire monitor/
      Not Avl or Avail      		 - -
      O2S (A/FS) Heater Monitor O2S (A/FS) heater monitor/
      Not Avl or Avail      		 - -
      O2S (A/FS) Heater Monitor O2S (A/FS) heater monitor/
      Compl or Incmpl      		 - -
      O2S (A/FS) Monitor O2S (A/FS) monitor/
      Not Avl or Avail      		 - -
      O2S (A/FS) Monitor O2S (A/FS) monitor/
      Compl or Incmpl      		 - -
      2nd Air Monitor 2nd air monitor/
      Not Avl or Avail      		 - -
      2nd Air Monitor 2nd air monitor/
      Compl or Incmpl      		 - -
      EVAP Monitor EVAP monitor/
      Not Avl or Avail      		 - -
      EVAP Monitor EVAP monitor/
      Compl or Incmpl      		 - -
      Catalyst Monitor Catalyst monitor/
      Not Avl or Avail      		 - -
      Catalyst Monitor Catalyst monitor/
      Compl or Incmpl      		 - -
      Component Monitor Comprehensive component monitor/
      Unable or Enable      		 - -
      Component Monitor Comprehensive component monitor/
      Compl or Incmpl      		 - -
      Fuel System Monitor ENA Fuel system monitor/
      Unable or Enable      		 - -
      Fuel System Monitor CMPL Fuel system monitor/
      Compl or Incmpl      		 - -
      Misfire Monitor ENA Misfire monitor/
      Unable or Enable      		 - -
      Misfire Monitor CMPL Misfire monitor/
      Compl or Incmpl      		 - -
      Heater Monitor ENA O2S (A/FS) heater monitor/
      Unable or Enable      		 - -
      Heater Monitor CMPL O2S (A/FS) heater monitor/
      Compl or Incmpl      		 - -
      O2S (A/FS) Monitor ENA O2S (A/FS) monitor/
      Unable or Enable      		 - -
      O2S (A/FS) Monitor CMPL O2S (A/FS) monitor/
      Compl or Incmpl      		 - -
      2nd Air Monitor ENA 2nd air monitor/
      Unable or Enable      		 - -
      2nd Air Monitor CMPL 2nd air monitor/
      Compl or Incmpl      		 - -
      EVAP Monitor ENA EVAP monitor/
      Unable or Enable      		 - -
      EVAP Monitor CMPL EVAP monitor/
      Compl or Incmpl      		 - -
      Catalyst Monitor ENA Catalyst monitor/
      Unable or Enable      		 - -
      Catalyst Monitor CMPL Catalyst monitor/
      Compl or Incmpl      		 - -
      Model Code Model code - Identifying the model code: UCK5##
      Engine Type Engine type - Identifying the engine type: 2UZFE
      Cylinder Number Cylinder number/
      Min.: 0, Max.: 255      		 - Identifying the cylinder number: 8
      Transmission Type Transmission type - Identifying the transmission type: ECT (5AT)
      Destination Destination - Identifying the destination: A (America)
      Model Year Model year/
      Min.: 0, Max.: 255      		 - Identifying the model year: 200#
      System Identification System identification - Identifying the engine system: Gasoline (gasoline engine)

      HINT:

      *: If no conditions are specifically stated for "idling", the shift lever is in the N or P position, and the A/C switch is OFF and all accessory switches are OFF.

  2. ACTIVE TEST 

    HINT:

    Using the intelligent tester or Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Warm up the engine.
    2. Turn the ignition switch OFF.
    3. Connect the intelligent tester or Techstream to the DLC3.
    4. Turn the ignition switch ON.
    5. Turn the tester ON.
    6. Enter the following menus:
      1. Intelligent tester - Select: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST /
      2. Techstream - Select: Powertrain / Engine and ECT / Active Test /
    7. According to the display on the tester, perform the Active Test.

      Intelligent tester: 

      ACTIVE TEST DETAIL (INTELLIGENT TESTER)

      Tester Display Test Part Control Range Diagnostic Note
      INJ VOL Change injection volume Between -12% and 25%
      • All injectors tested at the same time
      • Perform test at less than 3000 rpm
      • Injection volume can be changed in 1 % graduations within control range
      A/F CONTROL Change injection volume Lower by 12.5% or increase 25%
      • Perform test at less than 3000 rpm
      • A/F CONTROL enables checking and graphing of A/F (Air Fuel Ratio) sensor voltage outputs
      • To conduct test, select following menu items: ACTIVE TEST / A/F CONTROL / USER DATA / AFSB1S1 and O2SB1S2, then press YES and ENTER followed by F4
      INTAKE CTL VSV1 Activate VSV for intake control ON/OFF -
      EVAP VSV (ALONE) Activate purge VSV control ON/OFF -
      AC CUT SIG Control A/C cut signal ON/OFF -
      FUEL PUMP / SPD Activate fuel pump ON/OFF -
      TC/TE1 Turn on and off TC and TE1 connection ON/OFF
      • ON: TC and TE1 connected
      • OFF: TC and TE1 disconnected
      FC IDL PROHBT Prohibit idling fuel cut control ON/OFF -
      STARTER Activate the starter relay ON/OFF Engine is stopped
      ACC CUT Activate the ACC CUT relay ON/OFF Engine is stopped
      ETCS OPEN SLOW Throttle actuator ON: throttle valve opens slowly This test is possible when the following conditions are met:
      • Ignition switch ON
      • Engine does not start
      • Fully depressing accelerator pedal (APP: 58 degrees or more)
      ETCS CLOSE SLOW Throttle actuator ON: throttle valve closes slowly Same as above
      ETCS OPEN FAST Throttle actuator ON: throttle valve opens fast Same as above
      ETCS CLOSE FAST Throttle actuator ON: throttle valve closes fast Same as above
      VVTB1 Control Variable Valve Timing (VVT)[bank1]
      • 128 to 127% This valve added to present OCV control duty 100%: Maximum advance
      • 100%: Maximum retard
      • Engine stall or rough idle when VVT actuator operated by 100%
      • Test possible during idle
      VVT CTRL B1 Turn on and off Oil Control Valve (OCV) ON/OFF
      • Engine stalls or idles roughly when OCV turned ON
      • Normal engine running or idling when OCV OFF
      VVTB2 Control Variable Valve Timing (VVT) [bank 2]
      • 128 to 127% This valve added to present OCV control duty 100%: Maximum advance
      • 100%: Maximum retard
      • Engine stall or rough idle when VVT actuator operated by 100%
      • Test possible during idle
      VVT CTRL B2 Turn on and off Oil Control Valve (OCV) ON/OFF
      • Engine stalls or idles roughly when OCV turned ON
      • Normal engine running or idling when OCV OFF
      VACUUM PUMP Activate vacuum pump (built into canister pump module) ON/OFF -
      VENT VALVE Activate vent valve (built into canister pump module) ON/OFF -
      FUEL CUT #1 Cylinder #1 injector fuel cut ON/OFF This test is possible when the vehicle is stopped and the engine is idling
      FUEL CUT #2 Cylinder #2 injector fuel cut ON/OFF Same as above
      FUEL CUT #3 Cylinder #3 injector fuel cut ON/OFF Same as above
      FUEL CUT #4 Cylinder #4 injector fuel cut ON/OFF Same as above
      FUEL CUT #5 Cylinder #5 injector fuel cut ON/OFF Same as above
      FUEL CUT #6 Cylinder #6 injector fuel cut ON/OFF Same as above
      FUEL CUT #7 Cylinder #7 injector fuel cut ON/OFF Same as above
      FUEL CUT #8 Cylinder #8 injector fuel cut ON/OFF Same as above

      Techstream: 

      ACTIVE TEST DETAIL (TECHSTREAM)

      Tester Display Test Part Control Range Diagnostic Note
      Control the Injection Volume Change injection volume Between -12% and 25%
      • All injectors tested at the same time
      • Perform test at less than 3000 rpm
      • Injection volume can be changed in 1 % graduations within control range
      Control the Injection Volume for A/F Sensor Change injection volume Lower by 12.5% or increase 25%
      • Perform test at less than 3000 rpm
      • Control the Injection Volume for A/F Sensor enables checking and graphing of A/F (Air Fuel Ratio) sensor voltage outputs
      • To conduct test, select following menu items: Active Test / Control the Injection Volume for A/F Sensor / AFS B1 S1 and O2S B1 S2 or AFS B2 S1 and O2S B2 S
      Activate the VSV for Secondary Air Control Activate the Secondary Air System ON/OFF
      • Do not perform test for 5 seconds or more
      • After test, do not perform test again for 30 seconds
      Activate the VSV for Intake Control Activate VSV for intake control ON/OFF -
      Activate the VSV for Evap Control Activate purge VSV control ON/OFF -
      Control the A/C Cut Signal Control A/C cut signal ON/OFF -
      Control the Fuel Pump / Speed Activate fuel pump ON/OFF -
      Connect the TC and TE1 Turn on and off TC and TE1 connection ON/OFF
      • ON: TC and TE1 connected
      • OFF: TC and TE1 disconnected
      Control the Idle Fuel Cut Prohibit Prohibit idling fuel cut control ON/OFF -
      Activate the Starter Relay Activate the starter relay ON/OFF Engine is stopped
      Activate the ACC Cut Relay Activate the ACC CUT relay ON/OFF Engine is stopped
      Control the ETCS Open/Close Slow Speed Throttle actuator ON: throttle valve opens slowly This test is possible when the following conditions are met:
      • Ignition switch ON
      • Engine does not start
      • Fully depressing accelerator pedal (APP: 58 degrees or more)
      Control the ETCS Open/Close Fast Speed Throttle actuator ON: throttle valve opens fast Same as above
      Control the VVT Linear (Bank 1) Control Variable Valve Timing (VVT) [bank 1]
      • 128 to 127% This valve added to present OCV control duty 100%: Maximum advance
      • 100%: Maximum retard
      • Engine stall or rough idle when VVT actuator operated by 100%
      • Test possible during idle
      Control the VVT System (Bank1) Turn on and off Oil Control Valve (OCV) ON/OFF
      • Engine stalls or idles roughly when OCV turned ON
      • Normal engine running or idling when OCV OFF
      Control the VVT Linear (Bank2) Control Variable Valve Timing (VVT) [bank 2]
      • 128 to 127% This valve added to present OCV control duty 100%: Maximum advance
      • 100%: Maximum retard
      • Engine stall or rough idle when VVT actuator operated by 100%
      • Test possible during idle
      Control the VVT System (Bank2) Turn on and off Oil Control Valve (OCV) ON/OFF
      • Engine stalls or idles roughly when OCV turned ON
      • Normal engine running or idling when OCV OFF
      Activate the Vacuum Pump Activate vacuum pump (built into canister pump module) ON/OFF -
      Activate the VSV for Vent Value Activate vent valve (built into canister pump module) ON/OFF -
      Control the Cylinder#1 Fuel Cut Cylinder #1 injector fuel cut ON/OFF This test is possible when the vehicle is stopped and the engine is idling
      Control the Cylinder#2 Fuel Cut Cylinder #2 injector fuel cut ON/OFF Same as above
      Control the Cylinder#3 Fuel Cut Cylinder #3 injector fuel cut ON/OFF Same as above
      Control the Cylinder#4 Fuel Cut Cylinder #4 injector fuel cut ON/OFF Same as above
      Control the Cylinder#5 Fuel Cut Cylinder #5 injector fuel cut ON/OFF Same as above
      Control the Cylinder#6 Fuel Cut Cylinder #6 injector fuel cut ON/OFF Same as above
      Control the Cylinder#7 Fuel Cut Cylinder #7 injector fuel cut ON/OFF Same as above
      Control the Cylinder#8 Fuel Cut Cylinder #8 injector fuel cut ON/OFF Same as above
  3. SYSTEM CHECK (Using intelligent tester) 

    HINT:

    Performing a SYSTEM CHECK enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are set, and can detect potential malfunctions in the system. The SYSTEM CHECK can be performed with the intelligent tester.

    1. Connect the intelligent tester to the DLC3.
    2. Turn the ignition switch ON.
    3. Turn the tester ON.
    4. Enter the following menus: DIAGNOSIS / ENHANCED OBD II I SYSTEM CHECK /
    5. Perform the SYSTEM CHECK by referring to the table below.
      SYSTEM CHECK

      Tester Display Test Part Control Range Diagnostic Notes
      EVAP SYS CHECK (AUTOMATIC) Perform 5 steps in order to operate EVAP key-off monitor automatically 35°C (95°F) or less
      • If no DTCs in PENDING CODES menu after performing this test, system functioning normally
      • Refer to EVAP INSPECTION PROCEDURE
      EVAP SYS CHECK (MANUAL) Perform 5 steps in order to operate EVAP key-off monitor manually 35°C (95°F) or less
      AIR INJ CHECK (AUTOMATIC) Perform secondary air injection system operation automatically With warm engine, ignition switch turned OFF once
      • If no DTCs in PENDING CODE after performing this test, system functioning normally
      • Refer to inspection procedure for secondary air injection system DTCs
      • When performing AIR INJ CHECK operation after battery cable has been reconnected, wait for 7 minutes with ignition switch turned to ON or engine running
      • Turn ignition switch to OFF when SYSTEM CHECK finished
      AIR INJ CHECK (MANUAL) Perform 7 operations in order to operate air injection system monitor manually With warm engine, ignition switch turned OFF once
      • Used to detect malfunctioning parts
      • Refer to inspection procedure for secondary air injection system DTCs
      • When performing AIR INJ CHECK operation after battery cable has been reconnected, wait for 7 minutes with ignition switch turned to ON or engine running
      • Turn ignition switch to OFF when SYSTEM CHECK finishes
  4. SYSTEM CHECK (Using Techstream) 

    HINT:

    Performing a System Check enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are set, and can detect potential malfunctions in the system. The System Check can be performed with the Techstream.

    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch ON.
    3. Turn the tester ON.
    4. Enter the following menus: Powertrain / Engine and ECT / Utility /
    5. Perform the System Check by referring to the table below.
      SYSTEM CHECK

      Tester Display Test Part Control Range Diagnostic Notes
      Evaporative System Check (Automatic Mode) Perform 5 steps in order to operate EVAP key-off monitor automatically 35°C (95°F) or less
      Evaporative System Check (Manual Mode) Perform 5 steps in order to operate EVAP key-off monitor manually 35°C (95°F) or less
      Air Injection Check (Automatic Mode) Perform secondary air injection system operation automatically With warm engine, ignition switch turned OFF once
      • If no DTCs in Pending after performing this test, system functioning normally
      • Refer to inspection procedure for secondary air injection system DTCs
      • When performing Air Injection Check operation after battery cable has been reconnected, wait for 7 minutes with ignition switch turned to ON or engine running
      • Turn ignition switch to OFF when System Check finished
      Air Injection Check (Manual Mode) Perform 7 operations in order to operate air injection system monitor manually With warm engine, ignition switch turned OFF once
      • Used to detect malfunctioning parts
      • Refer to inspection procedure for secondary air injection system DTCs
      • When performing Air Injection Check operation after battery cable has been reconnected, wait for 7 minutes with ignition switch turned to ON or engine running
      • Turn ignition switch to OFF when System Check finishes
scientia non olet · About Mike's Workshop Manuals