Torque Specifications
2AZ-FE
Torque Specifications
| Part Tightened | N.m | kgf.cm | ft.lbf | |
|---|---|---|---|---|
| Lead wire of field frame x Magnetic switch | 5.9 | 60 | 52 in..lbf | |
| Starter x Engine | Bolt | 39 | 398 | 29 |
| Terminal 30 | 13 | 130 | 9 | |
| Starter Assy | ||||
| Commutator end frame assy x Motor terminal starter kit | 6.0 | 61 | 53 in..lbf | |
| Repair service starter kit x Motor terminal starter kit | 7.5 | 77 | 66 in..lbf | |
| Lead wire x Terminal C of starter | 6.5 | 66 | 58 in..lbf | |
| Generator assy x Engine | M8 | 21 | 214 | 15 |
| M10 | 52 | 530 | 38 | |
| Wiring harness clamp | 8.4 | 85 | 74 in..lbf | |
| Alternator wire | 9.8 | 100 | 7 | |
| Generator assy | ||||
| Rectifire end frame x Drive end frame (See page 19 - 15) | ||||
| Nut A | 4.5 | 46 | 39 in..lbf | |
| Nut B | 5.4 | 55 | 47 in..lbf | |
| Recrifire holder x Coil lead on rectifire end frame | 2.9 | 30 | 26 in..lbf | |
| Voltage regulator x Rectifire end frame | 2.0 | 20 | 18 in..lbf | |
| Brush holder x Rectifire end frame | 2.0 | 20 | 18 in..lbf | |
| Rear end cover x Rectifire holder | 4.4 | 45 | 39 in..lbf | |
| Plate terminal x Rectifire holder | 3.9 | 39 | 35 in..lbf | |
| Terminal insulator x Rectifire holder | 4.1 | 42 | 36 in..lbf | |
| Generator pulley x Rotor | 111 | 1,125 | 81 | |
1MZ-FE
Torque Specifications
| Part Tightened | N.m | kgf.cm | ft.lbf | |
|---|---|---|---|---|
| Lead wire of field frame x Magnetic switch | 5.9 | 60 | 52 in..lbf | |
| Starter x Engine | Bolt | 42 | 429 | 31 |
| Nut | 9.8 | 100 | 7 | |
| Starter Assy | ||||
| Commutator end frame assy x Motor terminal starter kit | 6.0 | 61 | 53 in..lbf | |
| Repair service starter kit x Motor terminal starter kit | 7.5 | 77 | 66 in..lbf | |
| Lead wire x Terminal C of starter | 6.5 | 66 | 58 in..lbf | |
| Generator x Engine | Bolt A | 58 | 592 | 43 |
| (see page 19 - 33) | Bolt B | 18 | 184 | 13 |
| Alternator wire | 9.8 | 100 | 7 | |
| Generator assy | ||||
| Rectifire end frame x Drive end frame | ||||
| For without cord clip | 4.5 | 46 | 39 in..lbf | |
| For with cord clip | 5.4 | 55 | 47 in..lbf | |
| Recrifire holder x Coil lead on rectifire end frame | 2.9 | 30 | 26 in..lbf | |
| Voltage regulator x Rectifire end frame | 2.0 | 20 | 18 in..lbf | |
| Brush holder x Rectifire end frame | 2.0 | 20 | 18 in..lbf | |
| Rear end cover x Rectifire holder | 4.4 | 45 | 39 in..lbf | |
| Plate terminal x Rectifire holder | 3.9 | 39 | 35 in..lbf | |
| Terminal insulator x Rectifire holder | 4.1 | 42 | 36 in..lbf | |
| Generator pulley x Rotor | 111 | 1,125 | 81 | |