Essential Special Service Tools For 1986 (VOL. 8, SST, NO. 006)
WARNING: This page is about the Pickup DX, 2D Pickup Extra Cab, 2.4 L, G52, which is a different variant/trim than selected.
Publication date: 1986-03-21Reference number: VOL. 8, SST, NO. 006
ESSENTIAL SPECIAL SERVICE TOOLS FOR 1986
TECHNICAL SERVICE BULLETIN
Reference Number(s): VOL. 8, SST, NO. 006, Date of Issue:
March 21, 1986
| COPYRIGHT: | © 2018 Toyota, USA License Agreement TMS1002 |
ESSENTIAL SPECIAL SERVICE TOOLS FOR 1986
Model(s): 1983-85 Toyota Camry, Supra, Cressida
1986 Toyota Vehicles
Volume: 8
Reference: SST - Special Service Tools
Bulletin No.: 006
Date: March 21, 1986
SERVICE INFORMATION
The following Special Service Tools are essential for repair of 1986 model vehicles.
ENGINE SPECIAL SERVICE TOOLS INFORMATION
ENGINE SPECIAL SERVICE TOOLS INFORMATION
| Tool Number | Description | Application | Illustration |
|---|---|---|---|
| 09043-88010-00 | Hexagon Wrench, 8mm (1/2" Drive) Use to remove or install cylinder head bolts on 3S-GE Engine. | Celica (GTS) | See Fig 1 |
| 09842-30040 | Wiring "D", EFI Inspection Connector differs from previous type injector. (Internal resistor not used) | Celica (GTS) | See Fig 2 |
TRANSMISSION AND CLUTCH SPECIAL SERVICE TOOLS INFORMATION
TRANSMISSION AND CLUTCH SPECIAL SERVICE TOOLS INFORMATION
| Tool Number | Description | Application | Illustration |
|---|---|---|---|
| 00002-00850 | Electronically Controlled Transmission (ECT) Analyzer (Includes storage case and Instruction Manual) Enables technician to bypass ECT computer for manual control of transmission functions. | 1983-86 Camry 1986 Celica 1983-86 Supra 1983-86 Cressida 1986 MR2 1986 RN | See Fig 3 |
| 09351-32190 | Measuring Terminal (Add to ATM Kit 09350-32190) Use with dial indicator to measure the clutch piston stroke. | Celica A140 E/L | See Fig 4 |
| 09351-32200 | Piston Spring No.3 Compressor (Add to ATM Kit 09350-32010) Use to compress the O/D clutch piston return spring. | Celica AL 140 E/L | See Fig 5 |
| 09509-25011 | Rear Axle Bearing Lock Nut Wrench Use to remove or install and adjust the preload on full floating rear axle | RN Dual Rear Wheel | See Fig 6 |
| 09520- 32050-01 | Drive-Shaft Remover/Replacer Attachment Use with slide hammer 09520-32040-01 to remove/install LH drive shaft. | Celica (GTS) | See Fig 7 |
STEERING AND FRONT AXLE SPECIAL SERVICE TOOLS INFORMATION
STEERING AND FRONT AXLE SPECIAL SERVICE TOOLS INFORMATION
| Tool Number | Description | Application | Illustration |
|---|---|---|---|
| 09608-16050 | Steering Knuckle Deflector Replacer Use in place of 09316-60016 to install the dust deflector. | Tercel | See Fig 8 |
| 09616-25010 | Steering Worm Bearing Adjusting Screw Wrench Use on RN worm and sector type power steering. | RN | See Fig 9 |
| 09617-24030 | Steering Rack End Wrench (34mm) Use to remove the rack ends on rack and pinion type power steering. | Van | See Fig 10 |
| 096l7-60010 | Steering Worm Bearing Adjusting Screw Locknut Wrench Use to remove/replace the locknut on worm and sector type power steering. | RN | See Fig 11 |
| 09631-00080 | Rack Cylinder Housing Seal Remover Use with handle 09631-12020-01 to remove the rack housing inner seal. | Van | See Fig 12 |
| 09631-20040 | Oil Seal "A" Replacer Use to install the guide nut oil seal. | Van | See Fig 13 |
| 09631-20100 | Steering Rack "E" Cover Use to protect rack seal when installing rack into housing. | Celica | See Fig 14 |
| 09631-20110 | Steering Rack "F" Cover Use to protect rack seal when installing rack into housing. | Van | See Fig 15 |
| 09631-20120 | Cylinder and Stopper Nut (46mm Hex) Use to remove/install cylinder end stopper nut. | Van | See Fig 16 |