Data Monitor: List

Keyless Access with Push Button Start (Power Supply)

Item	Contents	Standard/Unit	Note
Trip Count [count]	Time stamp information Ref. to COMMON (DIAGNOSTICS)>TIME STAMP .	Time	-
Count		-	-
Time Count [msec]		ms	-
Control Module Voltage	Keyless access control module power supply voltage status	ON: When the voltage is present OFF: When the voltage is not absent	-
Control Module Voltage (Backup)	Keyless access control module backup power supply voltage status	ON: When the voltage is present OFF: When the voltage is not absent	-
Remote Engine Starter State	Activated status of remote engine starter	Impossible: When the remote engine starter cannot be used Possible: When the remote engine starter can be used	-
Remote Engine Starter Stop Factor	-	-	-
Push start SW 1	Push button start SW1 status	ON: When the push button start SW is pressed OFF: When the push button start SW is not pressed	-
Push start SW 2	Push button start SW2 status	ON: When the push button start SW is pressed OFF: When the push button start SW is not pressed	-
Stop Light Switch	Brake pedal SW status	ON: When the brake pedal is depressed OFF: When the brake pedal is not depressed	-
Steering unlock SW	Steering lock control module status	ON: When the steering lock is unlocked OFF: Except when the steering lock is unlocked	-
Shift P signal (AT only)	Shift (P) status	ON: When the shift position is in P OFF: When the shift position is in other than P	-
Clutch SW (MT only)	Clutch pedal SW status	ON: When the clutch pedal is depressed OFF: When the clutch pedal is not depressed	-
Shift N signal (AT only)	Shift (N) status	ON: When the shift position is in N OFF: When the shift position is in other than N	-
Delivery mode signal (AT only)	Delivery mode status	ON: When in delivery mode OFF: When in other than delivery mode	-
ACC relay monitor	ACC relay drive status	ON: While the accessory relay drive is being output OFF: While the accessory relay drive is being stopped	-
IGN latch monitor	IGN latch status	ON: While the IGN latch signal is being output OFF: While the IGN latch signal is being stopped	-
STSW signal monitor	Engine start permission signal output status	ON: Press the push button ignition switch while depressing the brake pedal OFF: Status other than ON	-
IGN1/2 relay monitor (drive output)	Drive output monitoring status of IG relay	ON: While the IG relay 1/2 drive is being output OFF: While the IG relay is being stopped	-
IGN1/2 relay monitor (coil voltage)	Coil voltage monitoring status of IG relay	ON: While the IG relay 1/2 drive is being output OFF: While the IG relay is being stopped	-
ACCR signal	Accessory cut relay drive status	ON: While the accessory cut relay drive is being output OFF: While the accessory cut relay drive is being stopped	-
Vehicle speed signal	Driving condition	Stopped status: During vehicle stoppage Drive status: While driving	-
Engine Speed	Condition of the engine	Stopped: While the engine stops Rotating: While the engine is running	-
Vehicle identification	Vehicle recognition status	Vehicle types are displayed. GAS AT GAS MT HEV AT Auto Start Stop AT Auto Start Stop MT PHEV	-
Power supply status	Power supply status	All OFF status: IG1 relay, IG2 relay, and ACC relay are all OFF ACC relay ON status: Accessory ON IGN1 relay ON status: Ignition ON STSW Condition: Push button ignition switch is pressed with the brake pedal depressed	-
IGN1/2 external circuit abnormal	IGN relay output status	No detection: IGN 1/2 external circuit is normal detection: IGN 1/2 external circuit is not normal	-

Keyless Access with Push Button Start (Collation)

Item	Contents	Standard/Unit	Note
Trip Count [count]	Time stamp information Ref. to COMMON (DIAGNOSTICS)>TIME STAMP .	Time	-
Count		-	-
Time Count [msec]		ms	-
Driver's unlock touch sensor switch	Status of the touch sensor (unlock) built on the back surface of the driver's door outer handle	ON: ON when the touch sensor is touched OFF: OFF when the touch sensor is not touched	-
Passenger's unlock touch sensor switch	Status of the touch sensor (unlock) built on the back surface of the passenger's door outer handle	ON: ON when the touch sensor is touched OFF: OFF when the touch sensor is not touched	-
Driver's lock touch sensor SW	Status of the touch sensor (lock) built on the surface of the driver's door outer handle	ON: ON when the touch sensor is touched OFF: OFF when the touch sensor is not touched	-
Passenger's lock touch sensor SW	Status of the touch sensor (unlock) built on the back surface of the passenger's door outer handle	ON: ON when the touch sensor is touched OFF: OFF when the touch sensor is not touched	-
Rear Gate Request SW	Rear gate lock/unlock button status (OUTBACK model only)	ON: When the switch is ON OFF: When the switch is OFF	-
Trunk Request SW	Trunk opener button status (Sedan models only)	ON: When the switch is ON OFF: When the switch is OFF	-
Secret code Keyless registration	Secret code keyless registration status	unregistered: When not registered registered: When registered	-
Control Module Voltage	Keyless access control module power supply voltage status	ON: When the voltage is present OFF: When the voltage is not absent	-
Control Module Voltage (Backup)	Keyless access control module backup power supply voltage status	ON: When the voltage is present OFF: When the voltage is not absent	-
IGN SW	Ignition switch status	ON: When the switch is ON OFF: When the switch is OFF	-
B/up fuse	Keyless access control module backup fuse status	Connecting: When the fuse is connected OFF: When the fuse is not connected	-
Incorrect vehicle ID	ID information when performing the keyless access	No: Registered access key Yes: Unregistered access key	-
No response	Access key response status	No: There is a response from the access key when keyless access is performed Yes: There is no response from the access key when keyless access is performed	-
Incorrect response code, format	Response status from the access key	No: Response from the access key is normal when keyless access is performed Yes: Response from the access key differs when keyless access is performed	-
Exhausted battery	Access key battery status	No: When the access key battery is not depleted Yes: When the access key battery is depleted	-
Incorrect response code, ID code	Access key response status when performing the keyless access	No: Response from the access key is normal when keyless access is performed Yes: Response from the access key differs when keyless access is performed	-
Incorrect response code, collation result	Access key response status when performing the keyless access	No: Response from the access key is normal when keyless access is performed Yes: Response from the access key differs when keyless access is performed	-
Incorrect ID code	Access key response status when performing the keyless access	No: Response from the access key is normal when keyless access is performed Yes: Response from the access key differs when keyless access is performed	-
Incorrect rolling code	Access key response status when performing the keyless access	No: Response from the access key is normal when keyless access is performed Yes: Response from the access key differs when keyless access is performed	-
Smart Cancel	Keyless access function status	Normal: Keyless access function is activated Cancel: Keyless access function is deactivated	-
Simple Smart system cancel	Keyless access function status	Normal: Keyless access function is activated Cancel: Keyless access function is deactivated	-
Trunk Position	Trunk locked status	Lock: Trunk locked status Unlock: Trunk unlocked status	-
ID Code Box W/H Connection State	Connecting status of the terminal (i91) No. 18	OFF: ID code box is not connected Connecting: ID code box is connected	-
ID Code Box Existence Judging	ID code box connection setting	-	Normal Existence Judging
Immobilizer	Immobilizer set status	ON: When the immobilizer is set Unset: When the immobilizer is not set	-
Telematics Communication	Communication confirmation status of telematics remote engine starter	NG: When using unregistered DCM OK: When using registered DCM	-
Immobilizer Set Memory	Remote immobilizer set status	Set: When the remote immobilizer is set Unset: When the remote immobilizer is unset	-
Telematics Contract State	Subscription information of remote engine starter by telematics	Contract: Telematics function is in subscription status Not contract: Telematics function in no subscription status	-
Remote Engine Starter State	Activated status of remote engine starter	Impossible: When the remote engine starter cannot be used Possible: When the remote engine starter can be used	-
Remote engine starter communication ID confirmation	Remote control engine starter communication confirmation status	NG: When using an unregistered remote control engine starter OK: When using a registered remote control engine starter	-
Remote engine starter code registration confirmation	Remote control engine starter registration status	unregistered: When the code is not registered registered: When the code is registered	-
STLC sleep possible status	Steering lock control module sleep possible status	Impossible: Sleep is not possible possible: Sleep is possible	-
STLC wake-up transmission status	Steering lock control module wake-up transmission status	No transmission: Wake-up signal is not transmitted Transmission: Wake-up signal is transmitted	-
Lock side sensor status	Steering lock control module status	ON: Locked status OFF: Unlocked status	-
Unlock side sensor status	Steering lock control module status	ON: Locked status OFF: Unlocked status	-
Lock confirmation	Steering lock control module status	Unconfirmed: When not locked Confirmed: When locked	-
Unlock confirmation	Steering lock control module status	Unconfirmed: When not unlocked Confirmed: When unlocked	-
Sensor initialization	Steering lock control module status	Not Completed: Sensor initial operation not completed Completed: Sensor initial operation completed	-
Motor protection control status	Steering lock control module status	Possible: Motor protection control is activated Impossible: Motor protection control is not activated	-
Motor operation prohibition voltage evaluation	Steering lock control module status	ON: Motor operation is permitted OFF: Motor operation is prohibited	-
Diagnosis response	Steering lock control module status	Normal: Diagnostic communication is not in progress Response: Diagnostic communication is in progress	-
Sensor abnormal	Steering lock control module status	Normal: When the steering lock control module is normal Abnormal: When the steering lock control module is not normal	-
Motor power supply short-circuit abnormal	Steering lock control module status	Normal: When the steering lock control module is normal Abnormal: When the steering lock control module is not normal	-
Motor driver short-circuit abnormal	Steering lock control module status	Normal: When the steering lock control module is normal Abnormal: When the steering lock control module is not normal	-
IGN input open abnormal	IGN input status	Normal: When the IGN input is normal Abnormal: When the IGN input is not normal	-
Lock bar engagement abnormal	Steering lock bar status	Normal: Steering lock bar is normal Abnormal: Steering lock bar is stuck	-
Lock side relay operation	Steering lock control module status	Stopped: When in other than unlocked → locked Working: When in unlocked → locked	-
Unlock side relay operation	Steering lock control module status	Stopped: When in other than unlocked → locked Working: When in unlocked → locked	-
Motor drive FET drive	Steering lock control module status	Stopped: Except when the motor drive FET is operating Working: When the motor drive FET is operating	-
Motor reversal protection control	Steering lock control module status	Working: When the motor drive FET is operating Stopped: Except when the motor drive FET is operating	-
Engine start	Engine start permission status	E/G Start Permission: When the ignition switch is ON Indefinite: When the ignition switch is OFF	-
Sensor abnormal (past)	Steering lock control module status	Abnormal: When the steering lock control module is not normal Normal: When the steering lock control module is normal	-
Motor power supply short-circuit abnormal (past)	Steering lock control module status	Abnormal: When the steering lock control module is not normal Normal: When the steering lock control module is normal	-
Motor driver short-circuit abnormal (past)	Normal: When the steering lock control module is normal	Abnormal: When the steering lock control module is not normal Normal: When the steering lock control module is normal	-
Steering lock lock/unlock command reception history	Steering lock control module status	OFF: - ON (keep 10 sec): When steering lock changes as locked → unlocked, or unlocked → locked	-
Lock bar engagement abnormal (past)	Steering lock bar status	OFF: Steering lock bar is normal ON: Steering lock bar was stuck in the past	-
IGN input open abnormal (past)	IGN input status	Normal: When the IGN input is normal Abnormal: When the IGN input is not normal	-
STLC Abnormal EEPROM access	Steering lock control module status	Normal: When the steering lock control module is normal Abnormal: When the steering lock control module is not normal	-
ID code BOX sleep possible status	ID code box status	Impossible: Sleep is not possible possible: Sleep is possible	-
ID code BOX wake-up transmission status	ID code box status	No transmission: Wake-up signal is not transmitted Transmission: Wake-up signal is transmitted	-
ID code BOX Abnormal EEPROM access (now)	ID code box status	Normal: When the ID code box is normal Abnormal: When the ID code box is not normal	-
EGI code reception status	Engine start operation status	Reception: When the engine start operation is performed Not yet received: When the engine start operation is not performed	-
Engine start permission request reception status	Engine start permission request reception status	Reception: Ignition ON Not yet received: Ignition OFF	-
Code collation result between smart ECM and ID code box	Check result of collation code between keyless access control module and ID code box	Normal: When the engine start is possible Abnormal: When the engine start is not possible	-
Code collation result between steering locked ECM and ID code box	Check result of collation code between steering lock control module and ID code box	Abnormal: When the steering lock operation is possible Normal: When the steering lock operation is not possible	-
Steering lock unlock request reception status	Steering lock control module unlock request reception status	Reception (keep 10 sec): When the steering lock is performing unlock operation Not yet received: -	-
Steering lock lock request reception status	Steering lock control module lock request reception status	Reception (keep 10 sec): When the steering lock is performing lock operation Not yet received: -	-
Driver's external transmitter output circuit abnormal	Transmitter output circuit status	Normal: When the transmitter output circuit is normal Abnormal: When the transmitter output circuit is not normal	-
Passenger's external transmitter output circuit abnormal	Transmitter output circuit status	Normal: When the transmitter output circuit is normal Abnormal: When the transmitter output circuit is not normal	-
Driver's external transmitter output circuit abnormal (past)	Transmitter output circuit status	Normal: When the transmitter output circuit is normal Abnormal: There was a transmitter output error in the past	-
Passenger's external transmitter output circuit abnormal (past)	Transmitter output circuit status	Normal: When the transmitter output circuit is normal Abnormal: There was a transmitter output error in the past	-
ID code registration mode status	Immobilizer registration status	Normal: Not while registering/deleting Regist.: While registering Deletion: While deleting	-
Smart related ECM code registration mode status	Immobilizer registration status	Normal: When not in the smart related ECM code registration mode On mode: When in the smart related ECM code registration mode	-
ID code collation completion confirmation	Immobilizer registration status	Normal: Except when the ID code collation is complete Completed: When the ID code collation is complete	-
ID code registration completion confirmation	Immobilizer registration status	Normal: Except when the ID code registration is complete Completed: When the ID code registration is complete	-
Smart related ECM code registration completion confirmation	Immobilizer registration status	Normal: Except when the smart related ECM code registration is complete Completed: When the smart related ECM code registration is complete	-
Registered smart key confirmation status	Immobilizer registration status	Normal: Not while confirming the registered access keys Confirming: While confirming the registered access keys	-
Smart related ECM code confirmation status	Immobilizer registration status	Normal: Not while confirming the smart related ECM code Confirming: While confirming the smart related ECM code	-
ID code registration status	Immobilizer registration status	Normal: Not during the ID code registration Registering: During the ID code registration	-
Registration abnormal confirmation	Registration malfunction status	Normal: At normal condition Abnormal: Abnormal	-
ID code collation status	Immobilizer registration status	Normal: Not during the ID code registration Collating the immobilizer: During the ID code collation (immobilizer collation) Collating the smart: During the ID code collation (smart collation)	-
All registered keys confirmation status	Immobilizer registration status	Normal: Not while confirming all registered keys Confirming: While confirming all registered keys	-
Confirmed number of all registered keys	Immobilizer registration status	Display range: 0 - 7	-
Number of required registrations (smart)	Immobilizer registration status	Display range: 0 - 7	-
Number of collation completed (smart)	Immobilizer registration status	Display range: 0 - 7	-
Number of registration completed (smart)	Number of recognized keyless access control module	Display range: 0 - 7	-
Trunk Open Without Key	Trunk open customization without key status (Sedan models only)	ON: When customizing is ON OFF: When customizing is OFF	-
Steering unlock SW	Steering lock control module status	ON: When the steering lock is unlocked OFF: Except when the steering lock is unlocked	-
Shift P signal (AT only)	Shift (P) status	ON: When the shift position is in P OFF: When the shift position is in other than P	-
Vehicle type identification	Vehicle type identification	Vehicle type is displayed. SDN: Sedan WGN: OUTBACK	-