Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Scion >> 2016 >> iA Automatic Trans >> Repair and Diagnosis >> Body & Frame >> Windows >> Power Window Control System - Diagnostic Codes & Symptom Tests >> Power Window Control System >> DTC B109E-87: Remote Keyless Entry Missing Message [07/2015 - ] >> Procedure

DTC B109E-87: Remote Keyless Entry Missing Message [07/2015 - ]: Procedure

  1. VERIFY MAIN BODY ECU DTCS AGAIN 
    1. Clear the DTC for the main body ECU using the Techstream.

      Refer to DTC CHECK / CLEAR [07/2015 - ]

      Body Electrical > Body Control Module > Clear DTCs 

    2. Retrieve the main body ECU DTCs using the Techstream.

      Refer to DTC CHECK / CLEAR [07/2015 - ]

      Body Electrical > Body Control Module > Trouble Codes 

    3. Is the same DTC displayed?

      Result

      Result
      Yes
      No

    Result:  2

    No 

    See step  8

    Result:  1

    Yes 

    See step  2

  2. INSPECT ENGINE STOP AND START ECU CONNECTOR CONDITION 
    1. Switch the ignition off.
    2. Disconnect the negative battery cable.

      Refer to REMOVAL [07/2015 - ]

    3. Disconnect the engine stop and start ECU connector.
    4. Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
    5. Is the connector normal?

      Result

      Result
      Yes
      No

    Result:  2

    No 

    See step  14

    Result:  1

    Yes 

    See step  3

  3. INSPECT MAIN BODY ECU CONNECTOR CONDITION 
    1. Disconnect the main body ECU connector.
    2. Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
    3. Is the connector normal?

      Result

      Result
      Yes
      No

    Result:  2

    No 

    See step  13

    Result:  1

    Yes 

    See step  4

  4. INSPECT WIRING HARNESS BETWEEN ENGINE STOP AND START ECU AND MAIN BODY ECU FOR SHORT TO GROUND 
    1. Verify that the engine stop and start ECU and main body ECU connectors are disconnected.
    2. Inspect for continuity between engine stop and start ECU terminal D6-9 (wiring harness-side) and body ground.
    3. Is there continuity?

      Result

      Result
      Yes
      No

    Result:  2

    Yes 

    See step  12

    Result:  1

    No 

    See step  5

  5. INSPECT WIRING HARNESS BETWEEN ENGINE STOP AND START ECU AND MAIN BODY ECU FOR OPEN CIRCUIT 
    1. Verify that the engine stop and start ECU and main body ECU connectors are disconnected.
    2. Inspect for continuity between engine stop and start ECU terminal D6-9 (wiring harness-side) and main body ECU terminal E1-21 (wiring harness-side).
    3. Is there continuity?

      Result

      Result
      Yes
      No

    Result:  2

    No 

    See step  11

    Result:  1

    Yes 

    See step  6

  6. VERIFY IF MALFUNCTIONING LOCATION IS ENGINE STOP AND START ECU DEPENDING ON REPEATABILITY 
    1. Always reconnect all disconnected connectors.
    2. Connect the negative battery cable.

      Refer to INSTALLATION [07/2015 - ]

    3. Clear the DTC for the main body ECU using the Techstream.

      Refer to DTC CHECK / CLEAR [07/2015 - ]

      Body Electrical > Body Control Module > Clear DTCs 

    4. Retrieve the main body ECU DTCs using the Techstream.

      Refer to DTC CHECK / CLEAR [07/2015 - ]

      Body Electrical > Body Control Module > Trouble Codes 

    5. Is the same DTC displayed?

      Result

      Result
      Yes
      No

    Result:  1

    Yes 

    See step  10

    Result:  2

    No 

    See step  8

  7. VERIFY THAT REPAIRS HAVE BEEN COMPLETED 
    1. Always reconnect all disconnected connectors.
    2. Connect the negative battery cable.

      Refer to INSTALLATION [07/2015 - ]

    3. Clear the DTC for the main body ECU using the Techstream.

      Refer to DTC CHECK / CLEAR [07/2015 - ]

      Body Electrical > Body Control Module > Clear DTCs 

    4. Retrieve the main body ECU DTCs using the Techstream.

      Refer to DTC CHECK / CLEAR [07/2015 - ]

      Body Electrical > Body Control Module > Trouble Codes 

    5. Is the same DTC displayed?

      Result

      Result
      Yes
      No

    Result:  2

    Yes 

    See step  9

    Result:  1

    No 

    See step  8

  8. VERIFY IF OTHER DTCS DISPLAYED 
    1. Are any other DTCs displayed?

      Result

      Result
      Yes
      No

    Result:  1

    Yes 

    REPAIR OR REPLACE THE MALFUNCTIONING PART ACCORDING TO THE APPLICABLE DTC TROUBLESHOOTING. 

    1. Refer to DIAGNOSTIC TROUBLE CODE CHART [07/2015 - ]

    Result:  2

    No 

    DTC TROUBLESHOOTING COMPLETED. 

  9. REPEAT THE INSPECTION FROM STEP 1. 
    1. If the malfunction recurs, replace the main body ECU.

      Refer to REMOVAL [07/2015 - ]

    2. Go to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  8

  10. REPLACE THE ENGINE STOP AND START ECU. 
    1. Refer to SYSTEM DIAGRAM [07/2015 - ]
    2. Then go to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  7

  11. REFER TO THE WIRING DIAGRAM AND VERIFY WHETHER OR NOT THERE IS A COMMON CONNECTOR BETWEEN ENGINE STOP AND START ECU TERMINAL D6-9 AND MAIN BODY ECU TERMINAL E1-21. 
    1. If there is a common connector:
      1. Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
      2. Repair or replace the malfunctioning part.
    2. If there is no common connector:

      Repair or replace the wiring harness which has an open circuit.

    3. Go to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  7

  12. REFER TO THE WIRING DIAGRAM AND VERIFY WHETHER OR NOT THERE IS A COMMON CONNECTOR BETWEEN ENGINE STOP AND START ECU TERMINAL D6-9 AND MAIN BODY ECU TERMINAL E1-21. 
    1. If there is a common connector:
      1. Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
      2. Repair or replace the malfunctioning part.
    2. If there is no common connector:

      Repair or replace the wiring harness which has an open circuit.

    3. Go to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  7

  13. REPAIR OR REPLACE THE CONNECTOR. 
    1. Then go to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  7

  14. REPAIR OR REPLACE THE CONNECTOR. 
    1. Then go to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  7

scientia non olet · About Mike's Workshop Manuals