Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Nissan-Datsun >> 2021 >> Armada SL, RWD >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System (DTCS) (4 Of 5) >> Engine (ECM) >> DTC P1084: EVT Control Position Sensor >> DTC Diagnosis Procedure

DTC Diagnosis Procedure

  1. CHECK EXHAUST VALVE TIMING CONTROL POSITION SENSOR POWER SUPPLY CIRCUIT-I 
    1. Disconnect exhaust valve timing (EVT) control position sensor harness connector.
    2. Turn ignition switch ON.
    3. Check the voltage between exhaust valve timing control position sensor harness connector and ground.

      EVT control position sensor

      Ground

      Voltage (V)

      Bank

      Connector

      Terminal

      2

      F17

      1

      Ground

      Approx. 5

    Is the inspection result normal?

    YES

    GO TO 2.

    NO

    Repair open circuit, short to ground in harness or connectors.

  2. CHECK EVT CONTROL POSITION SENSOR GROUND CIRCUIT FOR OPEN AND SHORT 
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check the continuity between EVT control position sensor harness connector and ECM harness connector.

      EVT control position sensor

      ECM

      Continuity

      Bank

      Connector

      Terminal

      Connector

      Terminal

      2

      F17

      2

      F92

      63

      Existed
    4. Also check harness for short to power.

    Is the inspection result normal?

    YES

    GO TO 3.

    NO

    Repair open circuit, short to power in harness or connectors.

  3. CHECK EVT CONTROL POSITION SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT 
    1. Check the continuity between EVT control position sensor harness connector and ECM harness connector.

      EVT control position sensor

      ECM

      Continuity

      Bank

      Connector

      Terminal

      Connector

      Terminal

      2

      F17

      3

      F92

      68

      Existed
    2. Also check harness for short to ground and short to power.

    Is the inspection result normal?

    YES

    GO TO 4.

    NO

    Repair open circuit, short to ground or short to power in harness or connectors.

  4. CHECK EXHAUST VALVE TIMING CONTROL POSITION SENSOR 

    Refer to Component Inspection .

    Is the inspection result normal?

    YES

    GO TO 5.

    NO

    Replace malfunctioning exhaust valve timing control position sensor. Refer to TIMING CHAIN : Exploded View .

  5. CHECK CRANKSHAFT POSITION SENSOR 

    Refer to Component Inspection .

    Is the inspection result normal?

    YES

    GO TO 6.

    NO

    Replace crankshaft position sensor. Refer to DRIVE PLATE : Exploded View .

  6. CHECK CAMSHAFT POSITION SENSOR 

    Refer to Component Inspection .

    Is the inspection result normal?

    YES

    GO TO 7.

    NO

    Replace malfunctioning camshaft position sensor. Refer to TIMING CHAIN : Exploded View .

  7. CHECK CAMSHAFT SPROCKET (SIGNAL PLATE) 

    Check the following.

    • Accumulation of debris to the signal plate of camshaft sprocket (EXH)
      GNSJMBIA1571Z-571Courtesy of NISSAN NORTH AMERICA, INC.
    • Chipping signal plate of camshaft sprocket (EXH)

    Is the inspection result normal?

    YES

    GO TO 8.

    NO

    Remove debris and clean the signal plate of camshaft sprocket (EXH) or replace camshaft sprocket (EXH). Refer to TIMING CHAIN : Exploded View .

  8. CHECK INTERMITTENT INCIDENT 

    Refer to Inspection .

    INSPECTION END

scientia non olet · About Mike's Workshop Manuals