Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Nissan-Datsun >> 2016 >> Rogue SL, AWD >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System (DTCS) (2 Of 3) >> DTC Diagnosis >> DTC P0441: EVAP Control System >> DTC Description >> DTC Confirmation Procedure

DTC Confirmation Procedure

  1. CHECK DTC PRIORITY

    If DTC P0441 is displayed with DTC P2122, P2123, P2127, P2128 or P2138, first perform the trouble diagnosis for DTC P2122, P2123, P2127, P2128 or P2138.

    Is applicable DTC detected?

    YES 

    Perform diagnosis of applicable. Refer to DTC INDEX .

    NO 

    GO TO STEP 2  .

  2. PRECONDITIONING

    If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

    1. Turn ignition switch OFF and wait at least 10 seconds.
    2. Turn ignition switch ON.
    3. Turn ignition switch OFF and wait at least 10 seconds.

    Will CONSULT be used?

    YES 

    GO TO STEP 3  .

    NO 

    GO TO STEP 6  .

  3. PERFORM DTC CONFIRMATION PROCEDURE-1

    G-20 WITH CONSULT

    TESTING CONDITION: 

    Always perform test at a temperature of 5°C (41°F) or more. 

    1. Start engine and warm it up to normal operating temperature.
    2. Turn ignition switch OFF and wait at least 10 seconds.
    3. Turn ignition switch ON.
    4. Turn ignition switch OFF and wait at least 10 seconds.
    5. Start engine and let it idle for at least 70 seconds.
    6. Select "PURG FLOW P0441" of "EVAPORATIVE SYSTEM" in "DTC WORK SUPPORT" mode of "ENGINE" using CONSULT.
    7. Touch "START".

    Is "COMPLETED" displayed on CONSULT screen?

    YES 

    GO TO STEP 5  .

    NO 

    GO TO STEP 4  .

  4. PERFORM DTC CONFIRMATION PROCEDURE-2

    When the following conditions are met, "TESTING" will be displayed on the CONSULT screen. Maintain the conditions continuously until "TESTING" changes to "COMPLETED". (It will take at least 35 seconds.)

    Selector lever Suitable position
    VHCL SPEED SE 32 - 120 km/h (20 - 75 MPH)
    ENG SPEED 500 - 3, 800 rpm
    B/FUEL SCHDL 1.0 - 10.0 msec
    COOLAN TEMP/S More than 0°C (32°F)
    CAUTION:

    Always drive vehicle at a safe speed.

    NOTE:

    If "TESTING" does not change for a long time, retry from step 2. 

    Is "COMPLETED" displayed on CONSULT screen?

    YES 

    GO TO STEP 5  .

    NO 

    Perform DTC CONFIRMATION PROCEDURE again. GO TO STEP 2  .

  5. PERFORM DTC CONFIRMATION PROCEDURE-3

    Touch "SELF-DIAG RESULTS".

    Which is displayed on CONSULT screen?

    OK 

    INSPECTION END

    NG 

    Proceed to DIAGNOSIS PROCEDURE .

  6. PERFORM COMPONENT FUNCTION CHECK

    1. Lift up drive wheels.
    2. Start engine (VDC switch OFF) and warm it up to normal operating temperature.
    3. Turn ignition switch OFF and wait at least 10 seconds.
    4. Start engine and wait at least 70 seconds.
    5. Set voltmeter probes to ECM harness connector terminals as per the following.
      ECM
      Connector + -
      Terminal
      E16 114 124
    6. Check EVAP control system pressure sensor value at idle speed and note it.
    7. Establish and maintain the following conditions for at least 1 minute.
      Air conditioner switch ON
      Headlamp switch ON
      Rear window defogger switch ON
      Engine speed Approx. 3, 000 rpm
      Gear position Any position other than P, N or R
    8. Verify that EVAP control system pressure sensor value stays 0.1 V less than the value at idle speed (measured at step 6) for at least 1 second.

    Is the inspection result normal?

    YES 

    INSPECTION END

    NO 

    Proceed to DIAGNOSIS PROCEDURE .

scientia non olet · About Mike's Workshop Manuals