Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Nissan-Datsun >> 2014 >> Rogue SL, AWD >> Repair and Diagnosis >> Electrical >> Body Electrical >> Power Control System (IPDM/Er) >> Ecu Diagnosis Information >> IPDM E/R (Intelligent Power Distribution Module Engine Room) >> Reference Value >> Physical Values

Physical Values

Terminal Wire color Circuit Input/Output Ignition switch Condition Value
1 R Battery power supply Supply OFF - Battery voltage
2 L Battery power supply Supply OFF - Battery voltage
4 Y Illumination power supply Output   Lighting switch OFF 0 - 1 V
Lighting switch 1ST Battery voltage
8 BG VSCV power supply Output - - -
9 L Horn relay control Output   Horn is not activated Battery voltage
Horn is activated 0 - 1 V
12 B Signal ground Ground - - -
16 G Reverse lamp power supply Output ON Selector lever in any position other than R 0 - 1 V
Selector Lever in R Battery voltage
17 W Tail lamps power supply Output   Lighting switch OFF 0 - 1 V
Lighting switch 1ST Battery voltage
19 LG ECM ignition power supply Output OFF - 0 - 1 V
ON - Battery voltage
21 SB Rear height sensor signal Input - - -
22 P CAN-L Input/Output - - -
24 L CAN-H Input/Output - - -
25 SB Height sensors power supply Supply ON - 5 V
26 SB Height sensors ground Ground - - -
31 B Signal ground 2 Ground - - -
32(1) GR Push-button ignition switch signal Input - Push-button ignition switch pressed 0 - 1 V
Push button ignition switch released Battery voltage
32(2) GR Ignition switch signal Input - Ignition switch ON 0 - 1 V
Ignition switch OFF Battery voltage
33 BR Front wiper motor stop position Input ON Front wiper stop position 0 - 1 V
Any position other than front wiper stop position Battery voltage
39 L CAN-H Input/Output - - -
40 P CAN-L Input/Output - - -
43 LG Fuel injectors power supply Output OFF   0 - 1 V
ON   Battery voltage
44 R ECM power supply Supply OFF - Battery voltage
45 V Front wiper motor HI power supply Output ON Front wiper switch OFF 0 - 1 V
Front wiper switch HI Battery voltage
46 W Fuel pump power supply Output ON
RUN		 Approximately 1 second after turning the ignition switch ON Battery voltage
ON Approximately 1 second after turning the ignition switch ON 0 - 1 V
47 B Power ground Ground - - -
48 Y Front wiper motor LO power supply Output ON Front wiper switch OFF 0 - 1 V
Front wiper switch LO Battery voltage
49 R Daytime running lamp LH power supply Output   Lighting switch OFF 0 - 1 V
Lighting switch 1ST Battery voltage
50 L Headlamp LO LH power supply Output   Lighting switch OFF 0 - 1 V
Lighting switch 2ND Battery voltage
51 V Front fog lamp LH power supply Output   Front fog lamp switch OFF Battery voltage
Front fog lamp switch ON 0 - 1 V
52 W Hood switch signal Output   Hood closed 0 - 1 V
Hood open Battery voltage
53 GR LED headlamp fail signal LH Input - - -
54 LG Headlamp HI RH power supply Output   Lighting switch other than HI and PASS 0 - 1 V
Lighting switch HI Lighting switch PASS Battery voltage
55 SB Headlamp aiming motors power supply Output OFF   0 - 1 V
ON   Battery voltage
56 BG Parking lamp LH power supply Output   Lighting switch OFF 0 - 1 V
Lighting switch 1ST Battery voltage
57 W Front fog lamp RH power supply Output   Front fog lamp switch OFF Battery voltage
Front fog lamp switch ON 0 - 1 V
58 R Daytime running lamp RH power supply Output   Lighting switch OFF 0 - 1 V
Lighting switch 1ST Battery voltage
59 G Headlamp HI LH power supply Output   Lighting switch other than HI and PASS 0 - 1 V
Lighting switch HI Lighting switch PASS Battery voltage
60 Y LED headlamp fail signal RH Input - - -
61 GR Parking lamp RH power supply Output   Lighting switch OFF 0 - 1 V
Lighting switch 1ST Battery voltage
62 SB Headlamp LO RH power supply Output   Lighting switch OFF 0 - 1 V
Lighting switch 2ND Battery voltage
63 B Headlamp aiming motors ground Ground - - -
64 V Headlamp aiming motors signal Output - - -
65 P A/C compressor power supply Output RUN A/C switch OFF 0 - 1 V
A/C switch ON (A/C compressor operating) Battery voltage
66 R Ignition coils power supply Output - - -
67 V Throttle control motor relay control Input ON → OFF   0 - 1 V
↓
Battery voltage
↓
0 - 1 V
ON   0 - 1 V
70 BG TCM ignition power supply Output OFF - 0 - 1 V
ON - Battery voltage
71 SB Electrical control valve power supply Output OFF   0 - 1 V
ON   Battery voltage
72 GR Throttle control motor relay power supply Supply OFF More than a few seconds after turning ignition switch OFF 0 - 1 V
ON
OFF		 For a few seconds after turning ignition switch OFF Battery voltage
73 Y VBR and ECPVCS power supply Output - - -
75 BR HO2S 2 and A/F sensor 1 power supply Output - - -
76 P Fuel pump relay control Input ON
RUN		 Approximately 1 second after turning the ignition switch ON 0 - 1 V
ON Approximately 1 second or more after turning the ignition switch Battery voltage
78 L ILTCS, EVTCS, ECVCV and IVTCS power supply Output - - -
79 G TCM R range sw signal Input - - -
81 L ECM relay power supply Supply OFF - Battery voltage
83 G Starter motor power supply Output OFF   0 - 1 V
START   Battery voltage
84 LG Cooling fan relay-1 power supply Input - - Battery voltage
85 P Cooling fan relay-2 power supply Output ON or START Cooling fan OFF 0V
Cooling fan LO Battery voltage
86 GR Starter relay power supply Input ON or START - Battery voltage
87 L CAN-H Input/Output - - -
88 P CAN-L Input/Output - - -
92 GR Starter relay control Input - - -
93 P ECM relay control Input - - -
98 Y Electrical control valve control Output OFF - -
106 BR Cooling fan relay-3 control Output - - -
107 V Cooling fan relay-2 control Output - - -
(1) With Intelligent Key system
(2) With remote keyless entry
scientia non olet · About Mike's Workshop Manuals