Diagnosis Procedure

1. Turn ignition switch OFF.
2. Loosen and retighten ground screws on the body.

Refer to "GROUND INSPECTION ".

• ←: Vehicle front
• Body ground (1)

Fig 1: Identifying Body Ground

Courtesy of NISSAN NORTH AMERICA, INC.

OK or NG 

OK: GO TO 2.

NG: Repair or replace ground connections.

1. Disconnect EVAP control system pressure sensor (1) harness connector.
   • This illustration is a view from under vehicle
   • EVAP canister (2)
   • EVAP canister vent control valve (3)
2. Check sensor harness connector for water.

Water should not exist  .

Fig 2: Identifying EVAP Control System Pressure Sensor, EVAP Canister And EVAP Canister Vent Control Valve

Courtesy of NISSAN NORTH AMERICA, INC.

OK or NG 

OK: GO TO 3.

NG: Repair or replace harness connector.

1. Turn ignition switch ON.
2. Check voltage between EVAP control system pressure sensor terminal 3 and ground with CONSULT or tester.

Voltage: Approximately 5 V 

Fig 3: Checking EVAP Control System Pressure Sensor Power Supply Circuit-I

Courtesy of NISSAN NORTH AMERICA, INC.

OK or NG 

OK: GO TO 11.

NG: GO TO 4.

1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check harness continuity between EVAP control system pressure sensor terminal 3 and ECM terminal 76. Refer to Wiring Diagram .

Continuity should exist  .

OK or NG 

OK: GO TO 6.

NG: GO TO 5.

Check the following.

• Harness connectors E3, F2
• Harness connectors B9, E13
• Harness for open between EVAP control system pressure sensor and ECM

Repair open circuit.

Check harness for short to power and short to ground between the following terminals.

OK or NG 

OK: GO TO 7.

NG: Repair short to ground or short to power in harness or connectors.

Refer to TROUBLE DIAGNOSIS .

OK or NG 

OK: GO TO 8.

NG: Replace refrigerant pressure sensor. Refer to REMOVAL AND INSTALLATION FOR EXPANSION VALVE .

Refer to "COMPONENT INSPECTION ".

OK or NG 

OK: GO TO 9.

NG: Replace crankshaft position sensor (POS). Refer to CYLINDER BLOCK .

Refer to "COMPONENT INSPECTION ".

OK or NG 

OK: GO TO 16.

NG: GO TO 10.

Replace accelerator pedal assembly. Refer to ACCELERATOR CONTROL SYSTEM .

INSPECTION END 

1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check harness continuity between EVAP control system pressure sensor terminal 1 and ECM terminal 51. Refer to Wiring Diagram .

   Continuity should exist  .

4. Also check harness for short to ground and short to power.

OK or NG 

OK: GO TO 13.

NG: GO TO 12.

Check the following.

• Harness connectors E3, F2
• Harness connectors B9, E13
• Harness for open or short between EVAP control system pressure sensor and ECM

Repair open circuit or short to ground or short to power in harness or connectors.

1. Check harness continuity between ECM terminal 42 and EVAP control system pressure sensor terminal 2. Refer to Wiring Diagram .

   Continuity should exist  .

2. Also check harness for short to ground and short to power.

OK or NG 

OK: GO TO 15.

NG: GO TO 14.

Check the following.

• Harness connectors E3, F2
• Harness connectors B9, E13
• Harness for open or short between ECM and EVAP control system pressure sensor

Repair open circuit or short to ground or short to power in harness or connectors.

Refer to "COMPONENT INSPECTION ".

OK or NG 

OK: GO TO 16.

NG: Replace EVAP control system pressure sensor. Refer to REMOVAL AND INSTALLATION .

Refer to TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT .

INSPECTION END