Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Nissan-Datsun >> 2011 >> Sentra SE-R >> Repair and Diagnosis >> Body & Frame >> Windows >> Glass, Window System & Mirrors >> Service Information >> Power Window System >> Front Power Window RH Circuit Inspection (Power Window and Door Lock/Unlock Switch RH Operation)

Front Power Window RH Circuit Inspection (Power Window and Door Lock/Unlock Switch RH Operation)

  1. CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH OUTPUT SIGNAL
    1. Turn ignition switch OFF.
    2. Disconnect front power window motor RH.
    3. Turn ignition switch ON.
    4. Check voltage between front power window motor RH connector and ground.
      VOLTAGE SPECIFICATIONS

      Connector Terminals Condition Voltage (V) (Approx.)
      (+) (-)
      D105 3 Ground UP Battery voltage
      DOWN 0
      1 UP 0
      DOWN Battery voltage
      Fig 1: Checking Voltage Between Front Power Window Motor RH Connector Terminals 1, 3 And Ground
      G05922835Courtesy of NISSAN MOTOR CO., U.S.A.

      OK or NG 

      OK: Replace front power window motor RH. Refer to "REMOVAL AND INSTALLATION ".

      NG: GO TO 2.

  2. CHECK POWER SUPPLY CIRCUIT
    1. Turn ignition switch ON.
    2. Check voltage between power window and door lock/unlock switch RH connector D104 and ground.

      8 - Ground : Battery voltage 

      Fig 2: Checking Voltage Between Power Window And Door Lock/Unlock Switch RH Connector D104 Terminal 8 And Ground
      G04927871Courtesy of NISSAN MOTOR CO., U.S.A.

      OK or NG 

      OK: GO TO  4.

      NG: GO TO 3.

  3. CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH POWER SUPPLY CIRCUIT
    1. Turn ignition switch OFF.
    2. Disconnect BCM and power window and door lock/unlock switch RH.
    3. Check continuity between BCM connector (A) and power window and door lock/unlock switch connector (B).
      CONTINUITY SPECIFICATIONS

      A B Continuity
      Connector Terminal Connector Terminal
      M20 68 D104 8 Yes
      Fig 3: Checking Continuity Between BCM Connector (A) And Power Window And Door Lock/Unlock Switch Connector
      G04927872Courtesy of NISSAN MOTOR CO., U.S.A.
    4. Check continuity between BCM connector (A) and ground.
      CONTINUITY SPECIFICATIONS

      A Ground Continuity
      Connector Terminal
      M20 68 No

      OK or NG 

      OK: Check the condition of the harness and the connector.

      NG: Repair or replace harness.

  4. CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH OUTPUT SIGNAL
    1. Turn ignition switch ON.
    2. Check voltage between power window and door lock/unlock switch RH connector and ground.
      VOLTAGE SPECIFICATIONS

      Connector Terminals Condition Voltage (V) (Approx.)
      (+) (-)
      D104 7 Ground UP Battery voltage
      DOWN 0
      6 UP 0
      DOWN Battery voltage
      Fig 4: Checking Voltage Between Power Window And Door Lock/Unlock Switch RH Connector D104 Terminals 6, 7 And Ground
      G04927878Courtesy of NISSAN MOTOR CO., U.S.A.

      OK or NG 

      OK: GO TO 5.

      NG: GO TO  6.

  5. CHECK FRONT POWER WINDOW MOTOR RH CIRCUIT
    1. Turn ignition switch OFF.
    2. Disconnect front power window motor RH and power window and door lock/unlock switch RH.
    3. Check continuity between power window and door lock/unlock switch RH connector D104 (A) terminals 6, 7 and front power window motor RH connector D105 (B) terminals 1, 3.

      7 - 3 : Continuity should exist. 

      6 - 1 : Continuity should exist. 

      Fig 5: Checking Continuity Between Front Air Control Harness Connector M50 Terminal 19, 20 And Mode Door Motor Harness Connector M142 Terminal 1, 6
      G05884401Courtesy of NISSAN MOTOR CO., U.S.A.
    4. Check continuity between power window and door lock/unlock switch RH connector D104 (A) terminals 6, 7 and ground.

      6 - Ground : Continuity should not exist. 

      7 - Ground : Continuity should not exist. 

      OK or NG 

      OK: Replace front power window motor RH. Refer to "REMOVAL AND INSTALLATION ".

      NG: Repair or replace harness.

  6. CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH
    1. Turn ignition switch OFF.
    2. Check continuity between power window and door lock/unlock switch RH terminals.
      CONTINUITY SPECIFICATIONS

      Power window and door lock/unlock switch RH Terminals Condition Continuity
      6 8 DOWN Yes
      NEUTRAL or UP No
      11 NEUTRAL or UP Yes
      DOWN No
      7 8 UP Yes
      NEUTRAL or DOWN No
      12 NEUTRAL or DOWN Yes
      UP No
      Fig 6: Checking Continuity Between Power Window And Door Lock/Unlock Switch RH Terminals
      G04895951Courtesy of NISSAN MOTOR CO., U.S.A.

      OK or NG 

      OK: GO TO 7.

      NG: Replace power window and door lock/unlock switch RH. refer to "REMOVAL AND INSTALLATION ".

  7. CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH GROUND SUPPLY

    Check continuity between power window and door lock/unlock switch connector and ground.

    CONTINUITY SPECIFICATIONS

    Connector Terminals Continuity
    D104 11 Ground Yes
    12 Yes
    Fig 7: Checking Continuity Between Power Window And Door Lock/Unlock Switch RH Terminal 11, 12 And Ground
    G04895952Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Check the condition of the harness and the connector.

    NG: GO TO 8.

  8. CHECK GROUND SUPPLY CIRCUIT
    1. Disconnect main power window and door lock/unlock switch and power window and door lock/unlock switch RH.
    2. Check continuity between main power window and door lock/unlock switch connector (A) and power window and door lock/unlock switch RH connector (B).
      CONTINUITY SPECIFICATIONS

      A B Continuity
      Connector Terminal Connector Terminal
      D5 11 D104 11 Yes
      8 12 Yes
      Fig 8: Checking Continuity Between Lock/Unlock Switch And Power Window Connector (A) And Door Lock/Unlock Switch Rh Connector
      G05922842Courtesy of NISSAN MOTOR CO., U.S.A.
    3. Check continuity between main power window and door lock/unlock switch connector (A) and ground.
      CONTINUITY SPECIFICATIONS

      A Ground Continuity
      Connector Terminal
      D5 11 No
      8 No

      OK or NG 

      OK: GO TO 9.

      NG: Repair or replace harness.

  9. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH
    NOTE: Make sure the window lock switch in in the unlock position.
    Check continuity between main power window and door lock/unlock switch terminals.
    CONTINUITY SPECIFICATIONS

    Main power window and door lock/unlock switch Terminals Condition Continuity
    17 11 Lock switch UNLOCK Yes
    Lock switch LOCK No
    8 Lock switch UNLOCK Yes
    Lock switch LOCK No
    Fig 9: Checking Continuity Between Main Power Window And Door Lock/Unlock Switch Terminals
    G05922843Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Repair or replace harness.

    NG: Replace main power window and door lock/unlock switch. Refer to "REMOVAL AND INSTALLATION ".

scientia non olet · About Mike's Workshop Manuals