Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Nissan-Datsun >> 2010 >> Maxima S >> Repair and Diagnosis >> Body & Frame >> Windows >> Power Window Control System >> LH&RH Front Window Anti-Pinch >> Component Diagnosis >> Encoder >> Driver Side >> DRIVER SIDE : Diagnosis Procedure

DRIVER SIDE : Diagnosis Procedure

Regarding Wiring Diagram information, refer to "WIRING DIAGRAM ".

  1. CHECK ENCODER OPERATION
    1. Turn ignition switch ON.
    2. Check signal between main power window and door lock/unlock switch connector D7 terminals 9, 13 and ground with oscilloscope.
      TERMINAL REFERENCE

      Terminals Signal (Reference value)
      (+) (-)
      Main power window and door lock/unlock switch connector Terminal
      D7 9 Ground Refer to following signal
      13
      Fig 1: Checking Signal Between Main Power Window And Door Lock/Unlock Switch Connector D7 Terminals 9, 13
      G06781337Courtesy of NISSAN MOTOR CO., U.S.A.
      Fig 2: Driving Pattern Of Voltage Signal
      G06781338Courtesy of NISSAN MOTOR CO., U.S.A.

      Is the inspection result normal? 

      YES: Check intermittent incident. Refer to INTERMITTENT INCIDENT .

      NO: GO TO  2

  2. CHECK ENCODER POWER SUPPLY

    Check voltage between front power window motor LH connector D9 terminal 4 and ground.

    VOLTAGE SPECIFICATION

    Terminal Voltage (V) (Approx.)
    (+) (-)
    Front power window motor LH connector Terminal
    D9 4 Ground 10
    Fig 3: Checking Voltage Between Front Power Window Motor LH Connector D9 Terminal 4 And Ground
    G06781339Courtesy of NISSAN MOTOR CO., U.S.A.

    Is the inspection result normal? 

    YES: GO TO  4

    NO: GO TO  3

  3. CHECK HARNESS CONTINUITY 1
    1. Turn ignition switch OFF.
    2. Disconnect main power window and door lock/unlock switch connector D7 and front power window motor LH connector.
    3. Check continuity between main power window and door lock/unlock switch connector D7 (A) terminal 15 and front power window motor LH connector D9 (B) terminal 4.
      CONTINUITY CHART

      Main power window and door lock/unlock switch connector Terminal Front power window motor LH connector Terminal Continuity
      D7 (A) 15 D9 (B) 4 Yes
      Fig 4: Checking Continuity Between Main Power Window And Door Lock/Unlock Switch Connector D7 Terminal 15
      G06781340Courtesy of NISSAN MOTOR CO., U.S.A.
    4. Check continuity between main power window and door lock/unlock switch connector D7 (A) terminal 15 and ground.
      CONTINUITY CHART

      Main power window and door lock/unlock switch connector Terminal Ground Continuity
      D7 (A) 15 No

      Is the inspection result normal? 

      YES: Replace main power window and door lock/unlock switch. Refer to "REMOVAL AND INSTALLATION ".

      NO: Repair or replace harness or connectors.

  4. CHECK ENCODER GROUND CIRCUIT
    1. Turn ignition switch OFF.
    2. Disconnect front power window motor LH connector.
    3. Check continuity between front power window motor LH connector D9 terminal 6 and ground.
      CONTINUITY CHART

      Front power window motor LH connector Terminal Ground Continuity
      D9 6 Yes
      Fig 5: Checking Continuity Between Main Power Window And Door Lock/Unlock Switch Connector D7 Terminal 15
      G06781341Courtesy of NISSAN MOTOR CO., U.S.A.

      Is the inspection result normal? 

      YES: GO TO  6

      NO: GO TO  5

  5. CHECK HARNESS CONTINUITY 2
    1. Disconnect main power window and door lock/unlock switch connector D7.
    2. Check continuity between main power window and door lock/unlock switch connector D7 (A) terminal 2 and front power window motor LH connector D9 (B) terminal 6.
      CONTINUITY CHART

      Main power window and door lock/unlock switch connector Terminal Front power window motor LH connector Terminal Continuity
      D7 (A) 2 D9 (B) 6 Yes
      Fig 6: Checking Continuity Between Main Power Window And Door Lock/Unlock Switch Connector D7 Terminal 2
      G06781342Courtesy of NISSAN MOTOR CO., U.S.A.

      Is the inspection result normal? 

      YES: Replace main power window and door lock/unlock switch. Refer to "REMOVAL AND INSTALLATION ".

      NO: Repair or replace harness or connectors.

  6. CHECK HARNESS CONTINUITY 3
    1. Disconnect main power window and door lock/unlock switch connector D7.
    2. Check continuity between main power window and door lock/unlock switch connector D7 (A) terminals 9, 13 and front power window motor LH connector D9 (B) terminals 3, 5.
      CONTINUITY CHART

      Main power window and door lock/unlock switch connector Terminal Front power window motor LH connector Terminal Continuity
      D7 (A) 9 D9 (B) 5 Yes
      13 3
      Fig 7: Checking Continuity Between Main Power Window And Door Lock/ Unlock Switch Connector D7 Terminals 9, 13
      G06781343Courtesy of NISSAN MOTOR CO., U.S.A.
    3. Check continuity between main power window and door lock/unlock switch connector D7 (A) terminals 9, 13 and ground.
      CONTINUITY CHART

      Main power window and door lock/unlock switch connector Terminal Ground Continuity
      D7 (A) 9 No
      13

      Is the inspection result normal? 

      YES: Replace front power window motor LH. Refer to REMOVAL AND INSTALLATION .

      NO: Repair or replace harness or connectors.

scientia non olet · About Mike's Workshop Manuals