Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Nissan-Datsun >> 2006 >> Sentra SE-R >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 6 (Automatic Transmission - Introduction (Re4F03B)) >> Re4F03B >> On Board Diagnostic System Description >> Consult-II >> Data Monitor Mode (A/T) >> Notes

Data Monitor Mode (A/T): Notes

WARNING: This page is about a different variant/trim than selected.
DATA MONITOR MODE (A/T)

Item Display Monitor item Description Remarks
TCM input signals Main signals
Vehicle speed sensor 1 (A/T) (Revolution sensor) VHCL/S SE.A/T [km/h] or [mph] X -
  • Vehicle speed computed from signal of revolution sensor is displayed.
 When racing engine in "N" or "P" position with vehicle stationary, CONSULT-II data may not indicate 0 km/h (0 mph).
Vehicle speed sensor 2 (Meter) VHCL/S SE.MTR [km/h] or [mph] X -
  • Vehicle speed computed from signal of vehicle speed sensor is displayed.
 Vehicle speed display may not be accurate under approx. 10 km/h (6 mph). It may not indicate 0 km/h (0 mph) when vehicle is stationary.
           
Throttle position sensor [accelerator pedal position (APP) sensor] THRTL POS SEN [V] X -
  • Throttle position sensor

    [accelerator pedal position (APP) sensor] signal voltage is displayed.

  
A/T fluid temperature sensor FLUID TEMP SE [V] X -
  • A/T fluid temperature sensor signal voltage is displayed. Signal voltage lowers as fluid temperature rises.
  
Battery voltage BATTERY VOLT [V] X -
  • Source voltage of TCM is displayed.
  
Engine speed ENGINE SPEED [rpm] X X
  • Engine speed, computed from engine speed signal, is displayed.
 Engine speed display may not be accurate under approx. 800 rpm. It may not indicate 0 rpm even when engine is not running.
Overdrive control switch OVERDRIVE SW
[ON/OFF]		 X -
  • ON/OFF state computed from signal of overdrive control SW is displayed.
  
PN position switch PN POSI SW
[ON/OFF]		 X -
  • ON/OFF state computed from signal of PN position SW is displayed.
  
R position switch R POSITION SW
[ON/OFF]		 X -
  • ON/OFF state computed from signal of R position SW is displayed.
  
D position switch D POSITION SW
[ON/OFF]		 X -
  • ON/OFF state computed from signal of D position SW is displayed.
  
2 position switch 2 POSITION SW
[ON/OFF]		 X -
  • ON/OFF status, computed from signal of 2 position SW, is displayed.
  
1 position switch 1 POSITION SW
[ON/OFF]		 X -
  • ON/OFF status, computed from signal of 1 position SW, is displayed.
  
ASCD cruise signal ASCD CRUISE
[ON/OFF]		 X -
  • Status of ASCD cruise signal is displayed.

    ON... Cruising state

    OFF... Normal running state
  • This is displayed even when no ASCD is mounted.
ASCD OD cut signal ASCD OD CUT
[ON/OFF]		 X -
  • Status of ASCD OD release signal is displayed.

    ON... OD released

    OFF... OD not released
  • This is displayed even when no ASCD is mounted.
Kickdown switch KICKDOWN SW
[ON/OFF]		 X -
  • ON/OFF status, computed from signal of kick-down SW, is displayed.
  • This is displayed even when no kickdown switch is equipped.
Gear position GEAR - X
  • Gear position data used for computation by TCM, is displayed.
  
Selector lever position SLCT LVR POSI - X
  • Selector lever position data, used for computation by TCM, is displayed.
  • A specific value used for control is displayed if failsafe is activated due to error.
Vehicle speed VEHICLE SPEED
[km/h] or [mph]		 - X
  • Vehicle speed data, used for computation by TCM, is displayed.
  
Stop lamp switch BRAKE SW
[ON/OFF]		 X -
  • ON/OFF status are displayed.

    ON: Brake pedal is depressed.

    OFF: Brake pedal is released.

  
Throttle position THROTTLE POSI [/8] - X
  • Throttle position data, used for computation by TCM, is displayed.
  • A specific value used for control is displayed if failsafe is activated due to error.
Line pressure duty LINE PRES DTY
[%]		 - X
  • Control value of line pressure solenoid valve, computed by TCM from each input signal, is displayed.
  
Torque converter clutch solenoid valve duty TCC S/V DUTY
[%]		 - X
  • Control value of torque converter clutch solenoid valve, computed by TCM from each input signal, is displayed.
  
Shift solenoid valve A SHIFT S/V A
[ON/OFF]		 - X
  • Control value of shift solenoid valve A, computed by TCM from each input signal, is displayed.
 Control value of solenoid is displayed even if solenoid circuit is disconnected.
The "OFF" signal is displayed if solenoid circuit is shorted.
Shift solenoid valve B SHIFT S/V B
[ON/OFF]		 - X
  • Control value of shift solenoid valve B, computed by TCM from each input signal, is displayed.
Overrun clutch solenoid valve OVERRUN/C S/V
[ON/OFF]		 - X
  • Control value of overrun clutch solenoid valve computed by TCM from each input signal is displayed.
  
Self-diagnosis display lamp
(O/D OFF indicator lamp)		 SELF-D DP LMP
[ON/OFF]		 - X
  • Control status of O/D

    OFF indicator lamp is displayed.

  
X: Applicable
-: Not applicable
scientia non olet · About Mike's Workshop Manuals