Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Nissan-Datsun >> 2002 >> Sentra SE-R, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1102 (Power Window System) >> Power Window System >> Trouble Diagnosis Symptom Chart >> Limit Switch Circuit Check (Passenger Side)

Limit Switch Circuit Check (Passenger Side)

WARNING: This page is about a different car, the 2004 Nissan Murano. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) LIMIT SIGNAL 
    1. Turn ignition switch ON.
    2. Check voltage between front power window motor (passenger side) connector and ground.
      VOLTAGE CHECK CHART

      Connector Terminals (Wire color) Condition Voltage (V) (Approx.)
      (+) (-)
      D36 5 (G/W) Ground Passenger side door window is between fully-open and just before fully-closed position (ON) 0
      Passenger side door window is between just before fully-closed position and fully-closed position (OFF) 5
      Fig 1: Checking Voltage Between Front Power Window Motor (Passenger Side) Connector And Ground
      G03491660Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG

    1. OK: Limit switch circuit is OK.
    2. NG: GO TO 2.
  2. CHECK GROUND CIRCUIT 
    1. Turn ignition switch OFF
    2. Disconnect front power window motor (passenger side) connector.
    3. Check continuity between front power window motor (passenger side) connector D36 terminal 6 and ground.

      6 (W/B) - Ground Continuity should exist. 

      Fig 2: Checking Continuity Between Front Power Window Motor (Passenger Side) Connector D36 Terminal 6 And Ground
      G03491661Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG

    1. OK: GO TO  4 .
    2. NG: GO TO 3.
  3. CHECK HARNESS CONTINUITY 1 
    1. Disconnect front power window switch (passenger side) connector.
    2. Check continuity between front power window switch (passenger side) connector D35 terminal 3 and front power window motor (passenger side) connector D36 terminal 6.

      3 (W/B) - 6 (W/B) Continuity should exist. 

      Fig 3: Checking Continuity Between Front Power Window Switch (Passenger Side) Connector D35 Terminal 3 And Front Power Window Motor (Passenger Side) Connector D36 Terminal 6
      G03491662Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG

    1. OK: Replace front power window switch (passenger side).
    2. NG: Repair or replace harness between front power window) switch (passenger side) and front power window motor (passenger side).
  4. CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) OUTPUT SIGNAL 
    1. Turn ignition switch ON.
    2. Check voltage between front power window switch (passenger side) connector D35 terminal 15 and ground.

      15 (G/W) - Ground Approx. 5V 

      Fig 4: Checking Voltage Between Front Power Window Switch Connector D35 Terminal 15 And Ground
      G03491663Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG

    1. OK: GO TO 5.
    2. NG: Replace front power window switch (passenger side).
  5. CHECK HARNESS CONTINUITY 2 
    1. Turn ignition switch OFF
    2. Disconnect front power window switch (passenger side) connector.
    3. Check continuity between front power window switch (passenger side) connector D35 terminal 15 and front power window motor (passenger side) connector D36 terminal 5.

      15 (G/W) - 5 (G/W) Continuity should exist. 

      Fig 5: Checking Continuity Between Front Power Window Switch (Passenger Side) Connector D35 Terminal 15 And Front Power Window Motor (Passenger Side) Connector D36 Terminal 5
      G03491664Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG

    1. OK: GO TO 6.
    2. NG: Repair or replace harness between front power window switch (passenger side) and front power window motor (passenger side).
  6. CHECK LIMIT SWITCH 
    1. Connect front power window motor (passenger side) and front power window switch (passenger side) connector.
    2. Turn ignition switch ON.
    3. Check continuity between front power window motor (passenger side) connector D36 terminals 5 and 6.
      CONTINUITY CHECK CHART

      Connector Terminals (Wire color) Condition Continuity
      (+) (-)
      D36 5 (G/W) 6 (W/B) Passenger side door window is between fully-open and just before fully-closed position (ON) Yes (1)
      Passenger side door window is between just before fully-closed position and fully-closed position (OFF) No (1)
      (1) When checking continuity, turn ignition switch OFF.
      Fig 6: Checking Continuity Between Front Power Window Motor Connector D36 Terminals 5 And 6
      G03491665Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG

    1. OK: Check the condition of the harness and the connector.
    2. NG: Replace front power window motor (passenger side).
scientia non olet · About Mike's Workshop Manuals