Common Specs & Procedures
OUTLANDER SPORT & RVR COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | GENERAL SPECIFICATIONS | ||
| Torque | Torque specifications are included in article text and figures. | ||
| Axle Nut/Hub Nut | |||
| Front | 270 ± 27 N.m (199 ± 20 ft. lb.) | ||
| Rear | AWD: 270 ± 27 N.m (199 ± 20 ft. lb.) | ||
| Battery | BATTERY CHARGING | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | SERVICE SPECIFICATIONS | ||
| Torque | Torque specifications are included in article text and figures. | ||
| Charging | |||
| Generator | See GENERAL SPECIFICATIONS and SERVICE SPECIFICATIONS . | ||
| Torque | Torque specifications are included in article figures. | ||
| Drive Belts | |||
| Adjustment | DRIVE BELT TENSION CHECK | ||
| Drive Belt Routing | Refer to Drive Belt Routing Diagram figure under >> B << DRIVE BELT INSTALLATION . | ||
| Engine Cooling | |||
| General Service Specifications | Refer to COOLANT and SERVICE SPECIFICATIONS . | ||
| Radiator Cap Pressure | 14-18 psi | ||
| Thermostat R & I | REMOVAL AND INSTALLATION | ||
| Water Pump R & I | REMOVAL AND INSTALLATION | ||
| Engine Mechanical | |||
| Compression | Compression pressure (at engine speed of 200 r/min) 1,470 kPa (213 psi): Minimum 1,050 kPa (152 psi); Compression pressure difference of all cylinders: 98 kPa (14 psi) | ||
| Oil Pressure | At Idle: 29 kPa (4.2 psi) or more; At 3500 r/min: 294-686 kPa (43-100 psi) | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | Step 1: 40 N.m (30 ft. lb.); Step 2: 130 N.m (96 ft. lb.); Tighten bolts in specificed sequence. See Drive Plate Mounting Bolts Tightening Sequence figure in ENGINE MECHANICAL article. | ||
| Fuel System | |||
| Pressure Specification | 324 kPa (47 psi) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST | ||
| Fuel Filter Location | Fuel filter is part of fuel pump module, which is located in the fuel tank. | ||
| Fuel Filter R & I | FUEL TANK | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | N/A | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| Type | NGK DIFR6C11 | ||
| Gap | 1.0-1.1 mm (0.039-0.043 in.); Limit: 1.3 mm (0.051 in.) | ||
| Torque | 25 ± 5 N.m (18 ± 3 ft. lb.) | ||
| Starting | |||
| Starter | Refer to GENERAL SPECIFICATIONS and SERVICE SPECIFICATIONS . | ||
| Torque | Torque specifications are included in article figures. | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front: | SERVICE SPECIFICATIONS | ||
| Rear | SERVICE SPECIFICATIONS | ||
| Torque | |||
| Front | FASTENER TIGHTENING SPECIFICATIONS | ||
| Rear | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 98 ± 10 N.m (73 ± 7 ft. lb.) | ||