Manual Transaxle Overhaul - Lancer Evolution
- General Information
- General Specifications
- Service Specifications
- Fastener Tightening Specifications
- Sealants And Adhesives
- Lubricants
- Adjustment Snap Ring And Spacers
- Special Tools
- Transaxle
- Disassembly And Assembly
- Notes
- Disassembly Service Points
- <<A>> Steel Ball Removal
- <<B>> Spring Pin Removal
- <<C>> Reverse Idler Gear Assembly Removal
- <<D>> 3RD-4TH Speed Shift Fork/5TH Speed Shift Fork/Shift Lug/5TH Speed Shift Rail Assembly/Input Shaft Assembly/Output Shaft Assembly/1ST-2ND Speed Shift Fork/1ST-2ND Speed Shift Rail Assembly Removal
- <<E>> Spring Pin Removal
- Assembly Service Points
- >>A<< 3RD-4TH Speed Shift Fork/5TH Speed Shift Fork/Shift Lug/5TH Speed Shift Rail Assembly/Input Shaft Assembly/Output Shaft Assembly Removal
- >>B<< Spring Pin Installation
- >>C<< Reverse Idler Gear Assembly Installation
- >>D<< Spring Pin Installation
- >>E<< 5TH-Reverse Speed Shift Rail Installation
- >>F<< Reverse Shift Lever Installation
- >>G<< Transaxle Case Installation
- >>H<< Control Housing Installation
- >>I<< Back-Up Light Switch/1ST-2ND Speed Rail Switch Installation
- >>J<< Shift Cable Bracket Installation
- Inspection
- Transaxle Adjustment
- Disassembly And Assembly
- Input Shaft
- Disassembly And Assembly
- Notes
- Disassembly Service Points
- <<A>> 5TH Speed Gear/Synchronizer Inner Ring/Synchronizer Cone/Synchronizer Outer Ring/5TH Speed Synchronizer Hub/Taper Roller Bearing/Synchronizer Key Stopper Plate/5TH Speed Synchronizer Sleeve Removal
- <<B>> 3RD Speed Gear/5TH Speed Gear Sleeve/4TH Speed Gear/Needle Roller Bearing/4TH Speed Gear Sleeve/Synchronizer Outer Ring/Synchronizer Cone/Synchronizer Inner Ring/3RD-4TH Speed Synchronizer Sleeve/3RD-4TH Speed Synchronizer Hub/Thrust Bearing/3RD Speed Gear Removal
- <<C>> Taper Roller Bearing Removal
- Assembly Service Points
- >>A<< Taper Roller Bearing Installation
- >>B<< Thrust Bearing Installation
- >>C<< 3RD-4TH Speed Synchronizer Hub/3RD-4TH Speed Synchronizer Sleeve Installation
- >>D<< 4TH Speed Gear Sleeve Installation
- >>E<< 5TH Speed Gear Sleeve Installation
- >>F<< 5TH Speed Synchronizer Hub/5TH Synchronizer Sleeve Installation
- >>G<< Taper Roller Bearing Installation
- >>H<< Snap Ring Installation
- >>I<< Oil Seal Installation
- Inspection
- Disassembly And Assembly
- Output Shaft
- Disassembly And Assembly
- Notes
- Disassembly Service Points
- <<A>> Taper Roller Bearing Removal
- <<B>> Taper Roller Bearing Removal
- <<C>> 5TH Speed Gear/4TH Speed Gear Removal
- <<D>> 3RD Speed Gear Removal
- <<E>> Needle Roller Bearing/Synchronizer Cone/Synchronizer Outer Ring/Synchronizer Inner Ring/Thrust Bearing/2ND Speed Gear Sleeve/1ST-2ND Speed Synchronizer Hub/1ST Speed Gear/1ST Speed Gear Sleeve Removal
- Assembly Service Points
- >>A<< 1ST Speed Gear Sleeve Installation
- >>B<< Thrust Bearing Installation
- >>C<< 1ST-2ND Speed Synchronizer Hub Installation
- >>D<< 1ST-2ND Speed Synchronizer Sleeve Installation
- >>E<< 2ND Speed Gear Sleeve Installation
- >>F<< 3RD Speed Gear Installation
- >>G<< Snap Ring Installation
- >>H<< 4TH Speed Gear Installation
- >>I<< 5TH Speed Gear Installation
- >>J<< Taper Roller Bearing Installation
- >>K<< Snap Ring Installation
- >>L<< Taper Roller Bearing Installation
- >>M<< Oil Seal Installation
- Inspection
- Disassembly And Assembly
- Reverse Idler Gear
- Control Housing
- Select Lever
- Clutch Housing
- Transaxle Case
- Center Differential
- Transfer