Automatic Trans: Overhaul
- General Information
- Special Tools
- Transmission And Transfer
- Transfer Case Adapter
- Transmission
- Reverse And Overdrive Clutches
- Disassembly And Assembly
- Notes
- Disassembly Service Point
- Assembly Service Points
- >> A << D-Ring Installation
- >> B << Reverse Clutch Piston Installation
- >> C << Return Spring Installation
- >> D << Snap Ring Installation
- >> E << Clutch Plate/Clutch Disc/Reaction Plate Installation
- >> F << Snap Ring Installation
- >> G << Clutch Plate/Clutch Disc/Reaction Plate Installation
- >> H << Snap Ring Installation
- Disassembly And Assembly
- Second Brake
- Low Reverse Annulus Gear
- Center Support
- UNDERDRIVE Clutch
- Valve Body
- Disassembly And Assembly
- Notes
- Disassembly Service Point
- Assembly Service Points
- >> A << Solenoid Valve Installation
- >> B << Dowel Pin Installation
- >> C << Knock Bushing Installation
- >> D << Knock Bushing Installation
- >> E << Spring/Steel Ball (Line Relief) Installation
- >> F << Spring/Steel Ball (Orifice Check Ball)/Ball (Orifice Check Ball)/Damping Valve Spring/Seal Ring/Damping Valve Installation
- >> G << Manual Valve Installation
- Disassembly And Assembly
- Direct Annulus Gear
- Direct Clutch
- OUTPUTSHAFT Support
- Transfer
- Disassembly And Assembly
- Notes
- Disassembly Service Points
- Assembly Service Points
- >> A << Oil Guide Installation
- >> B << Oil Seal Installation
- >> C << Rear Bearing Retainer Installation
- >> D << Snap Ring Installation
- >> E << H-L Shift Fork/H-L Clutch Sleeve Installation
- >> F << Spacer Installation
- >> G << Transfer Case Plate Installation
- >> H << Snap Ring Installation
- >> I << Steel Ball/Spacer Installation
- >> J << 2-4WD Shift Fork/2-4WD Clutch Sleeve Installation
- >> K << Snap Ring Installation
- >> L << Synchronizer Outer Ring/Synchronizer Cone/Synchronizer Inner Ring Installation
- >> M << Drive Sprocket/Front Output Shaft/Chain Installation
- >> N << Rear Output Shaft Installation
- >> O << Chain Cover Installation
- >> P << Snap Ring Installation
- >> Q << Spacer Installation
- >> R << Oil Seal Installation
- >> S << Rear Cover Installation
- >> T << Main Shift Rail/Shift Actuator Installation
- >> U << Shift Rail Drive Gear Installation
- >> V << Transfer Case Cover Installation
- >> W << 2-4WD Detection Switch/4H Detection Switch/Center Differential Lock Detection Switch/2WD Detection Switch/4LLC Detection Switch Installation
- Inspection
- Disassembly And Assembly
- Transfer Case Plate
- Input Gear
- Countershaft Gear
- Rear Output Shaft
- Front Output Shaft
- Transfer Drive Shaft
- SHIFTRAIL Drive Gear
- 2-4 Shift Rail/H-L Shift Rail
- Specifications
- Torque Specification
- General Specifications
- Service Specifications
- Valve Body Spring Identification
- Adjusting Plate, Snap Ring And Spacers
- Transmission
- Thrust race (For adjustment of direct planetary carrier end play)
- Snap ring (For adjustment of underdrive clutch and overdrive clutch end play)
- Thrust race (For adjustment of input shaft end play)
- Snap ring (For adjustment of overdrive clutch return spring retainer end play)
- Pressure plate (For adjustment of second brake end play)
- Snap ring (For adjustment of center support and brake reaction plate end play)
- Snap ring (For adjustment of reverse clutch end play)
- Snap ring (For adjustment of direct clutch end play)
- Pressure plate (For adjustment low/reverse brake end play)
- Transfer
- Snap ring (For adjustment input gear bearing end play)
- Spacer (For adjustment of countershaft gear end play)
- Snap ring (For adjustment of countershaft gear bearing end play)
- Snap ring (For adjustment of H-L clutch hub end play)
- Spacer (For adjustment of rear output shaft to chain cover preload)
- Spacer (For adjustment of rear output shaft to rear cover clearance)
- Snap ring (For adjustment annulus gear end play)
- Transmission
- Sealants And Adhesives