Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Mazda >> 2024 >> MX-5 Miata Club >> Repair and Diagnosis >> Engine Performance >> System >> On-Board Diagnostic - Engine Control - Introduction (2 Of 2) >> Simulation Table [Pcm ]

Simulation Table [Pcm ]

-: Not applicable

SIMULATION (PCM - SKYACTIV-G)

Simulation item Unit/Operation Data contents Operation condition
Engine condition Other condition
A/C_SW FALSE/TRUE
  • Select FALSE/TRUE to disengage/engage the magnetic clutch.
  • Under the following conditions:
    • Idle (no load)
 -
AIRSHUT_POS_COMD % Open
NOTE:
  • Displays in the M-MDS but it does not operate.
CHARGE_LAMP No (False)/Yes (True)
  • Select No (False)/Yes (True) to turn on/off the charging system warning light.
  • Select No (False)/Yes (True) to display/not display the charging system warning indication on the multi-information display.
  • Under the following conditions:
    • Ignition switch ON (engine off)
    • Idle
    • Racing (not idle)
 -
CSTR_VENT_SOL_DUTY %
  • Changes % and forcibly drives/stops CV solenoid valve.
  • Under the following conditions:
    • Ignition switch ON (engine off)
    • Idle
    • Racing (not idle)
CAUTION:
  • Do not add fuel with the CV solenoid valve closed. Otherwise, it will result in air pollution because the evaporative gas in the fuel tank will escape directly into the atmosphere.
NOTE:
  • Override drive parameter: 0-100%
EGR_COMD %
NOTE:
  • Displays in the M-MDS but it does not operate.
ENG_COOL_VLV_POS_COMD °(deg)
NOTE:
  • Displays in the M-MDS but it does not operate.
ENG_RPM_DSD Rpm
  • Changes value (Rpm) to forcibly vary engine speed.
  • Under the following conditions:
    • Idle
    • Racing (not idle)
  • The use in the following ranges is recommended:
    • Engine coolant temperature 75-95°C {167-203°F}
    • Vehicle stopped
    • Override drive parameter: 550-2, 000 rpm
EX_SHUT_VLV_DSD °(deg)
NOTE:
  • Displays in the M-MDS but it does not operate.
FAN %
  • Changes % and forcibly drives/stops fan control module.
  • Under the following conditions:
    • Idle
NOTE:
  • Override drive parameter: 0-90%
FP_DUTY %
  • Changes % and forcibly drives/stops fuel pump.
  • Under the following conditions:
    • Ignition switch ON (engine off)
    • Idle
    • Racing (not idle)
WARNING:
  • Do not use the simulation function while the fuel hose between the high pressure fuel pump and fuel tank is removed.
NOTE:
  • Override drive parameter: 5-95%
FUEL_PUMP_REQ Off/On
  • Changes Off/On and forcibly drives/stops fuel pump.
  • Under the following conditions:
    • Ignition switch ON (engine off)
    • Idle
    • Racing (not idle)
 -
H_SPD_FAN Off/On
  • Select Off/On to forcibly drive/stop the cooling fan at high speed.
 - -
INJ Fuel Injectors under PCM control/Fuel Injector 1 requested closed/Fuel Injector 2 requested closed/Fuel Injector 3 requested closed/Fuel Injector 4 requested closed/Fuel Injector 5 requested closed/Fuel Injector 6 requested closed/Fuel Injector 7 requested closed/Fuel Injector 8 requested closed/Fuel Injector 9 requested closed/Fuel Injector 10 requested closed/Fuel Injector 11 requested closed/Fuel Injector 12 requested closed/All Fuel Injectors requested closed
  • Forcibly stops the fuel injectors while the engine is idling.
  • Under the following conditions:
    • Idle
WARNING:
  • Do not use the simulation function while the vehicle is being driven. Stopping the fuel ejection causes the engine to stall which may cause the brakes to not function.
L_SPD_FAN Off/On
  • Select Off/On to forcibly drive/stop the cooling fan at low speed.
 - -
M_SPD_FAN Off/On
  • Select Off/On to forcibly drive/stop the cooling fan at middle speed.
 - -
MIL Off/On
  • Select Off/On to turn on/off the check engine light.
  • Under the following conditions:
    • Ignition switch ON (engine off)
    • Idle
    • Racing (not idle)
 -
OIL_PRES_SOL OFF/ON
  • Select OFF/ON to forcibly drive/stop the engine oil solenoid valve.
 - -
OIL_PUMP_DUTY % Duty Cycle
  • Changes % and forcibly drives/stops engine oil solenoid valve
  • Under the following conditions:
    • Idle
NOTE:
  • Override drive parameter: 0-100%
PRG_DUTY %
  • Changes % and forcibly drives/stops purge solenoid valve.
  • Under the following conditions:
    • Ignition switch ON (engine off)
    • Idle
    • Racing (not idle)
NOTE:
  • Override drive parameter: 0%
    • Purge solenoid valve: Close
  • Override drive parameter: 100%
    • Purge solenoid valve: Open
WASTEGATE_POS_SIMULATON %
NOTE:
  • Displays in the M-MDS but it does not operate.
WHEEL_DRIVE_CTRL_COMD -
NOTE:
  • Displays in the M-MDS but it does not operate.
scientia non olet · About Mike's Workshop Manuals