Diagnostic Procedure

DTC P0532:00 DIAGNOSTIC PROCEDURE

STEP	INSPECTION		ACTION
1	RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION NOTE: Recording can be facilitated using the screen capture function of the PC. Record the snapshot data on the repair order.	-	Go to the next step.
2	VERIFY RELATED REPAIR INFORMATION AVAILABILITY Verify related Service Bulletins and/or on-line repair information availability. Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information. If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	INSPECT REFRIGERANT PRESSURE SENSOR CONNECTOR CONDITION Switch the ignition off. Disconnect the refrigerant pressure sensor connector. Inspect for poor connection (such as damaged/pulled-out pins, corrosion). Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 9.
3		No	Go to the next step.
4	INSPECT REFRIGERANT PRESSURE SENSOR CIRCUIT FOR SHORT TO GROUND Verify that the refrigerant pressure sensor connector is disconnected. Inspect for continuity between the following terminals (wiring harness-side) and body ground: Refrigerant pressure sensor terminal C Refrigerant pressure sensor terminal B Is there continuity?	Yes	Disconnect the PCM connector and inspect the wiring harness for short to ground. If the short to ground circuit could be detected in the wiring harness: Refer to appropriate wiring diagram and verify whether or not there is a common connector between the following terminals: Refrigerant pressure sensor terminal C-PCM terminal 2Y Refrigerant pressure sensor terminal B-PCM terminal 2W If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has a short to ground. If the short to ground circuit could not be detected in the wiring harness: Replace the PCM (short to ground in the PCM internal circuit). (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.5T] .) Go to Step 9.
4		No	Go to the next step.
5	INSPECT PCM CONNECTOR CONDITION Disconnect the PCM connector. Inspect for poor connection (such as damaged/pulled-out pins, corrosion). Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 9.
5		No	Go to the next step.
6	INSPECT REFRIGERANT PRESSURE SENSOR SIGNAL CIRCUIT AND GROUND CIRCUIT FOR SHORT TO EACH OTHER Verify that the refrigerant pressure sensor and PCM connectors are disconnected. Inspect for continuity between refrigerant pressure sensor terminals B and A (wiring harness-side). Is there continuity?	Yes	Refer to appropriate wiring diagram and verify whether or not there is a common connector between the following terminals: Refrigerant pressure sensor terminal B-PCM terminal 2W Refrigerant pressure sensor terminal A-PCM terminal 2V If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to each other. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has a short to each other. Go to Step 9.
6		No	Go to the next step.
7	INSPECT REFRIGERANT PRESSURE SENSOR POWER SUPPLY CIRCUIT FOR OPEN CIRCUIT Verify that the refrigerant pressure sensor and PCM connectors are disconnected. Inspect for continuity between refrigerant pressure sensor terminal C (wiring harness-side) and PCM terminal 2Y (wiring harness-side). Is there continuity?	Yes	Go to the next step.
7		No	Refer to appropriate wiring diagram and verify whether or not there is a common connector between refrigerant pressure sensor terminal C and PCM terminal 2Y. If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has an open circuit. Go to Step 9.
8	INSPECT REFRIGERANT PRESSURE SENSOR Reconnect all disconnected connectors. Inspect the refrigerant pressure sensor. (See REFRIGERANT PRESSURE SENSOR INSPECTION .) Is there any malfunction?	Yes	Replace the refrigerant pressure sensor, then go to the next step. (See REFRIGERANT PRESSURE SENSOR REMOVAL/INSTALLATION .)
8		No	Go to the next step.
9	VERIFY DTC TROUBLESHOOTING COMPLETED Always reconnect all disconnected connectors. Clear the DTC from the PCM memory using the M-MDS. (See CLEARING DTC [PCM (SKYACTIV-G 2.5T)] .) Perform the KOEO or KOER self test. (See KOEO/KOER SELF TEST [PCM (SKYACTIV-G 2.5T)] .) Is the same Pending DTC present?	Yes	Repeat the inspection from Step 1. If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.5T] .) Go to the next step.
9		No	Go to the next step.
10	VERIFY AFTER REPAIR PROCEDURE Perform the "AFTER REPAIR PROCEDURE". (See AFTER REPAIR PROCEDURE [PCM (SKYACTIV-G 2.5T)] .) Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [PCM (SKYACTIV-G 2.5T)] .)
10		No	DTC troubleshooting completed.