| A/C_SW |
Off/On |
- Select Off/On to disengage/engage the magnetic clutch.
|
- Under the following conditions:
|
|
| AIRSHUT_POS_COMD |
% Open |
- Changes % to forcibly open/close the active air shutter.
|
|
NOTE:
- Override drive parameter: 0-100°
|
| CHARGE_LAMP |
No(False)/Yes(True) |
- Select No/Yes to turn on/off the charging system warning light.
- Select No/Yes to display/not display the charging system warning indication on the multi-information display.
|
- Under the following conditions:
- Ignition is switched ON (engine off)
- Idle - Racing (not idle)
|
|
| CSTR_VENT_SOL_DUTY |
% |
- Changes % and forcibly drives/stops CV solenoid valve.
|
- Under the following conditions:
- Ignition is switched ON (engine off)
- Idle
|
CAUTION:
- Do not add fuel with the CV solenoid valve closed. Otherwise, it will result in air pollution because the evaporative gas in the fuel tank will escape directly into the atmosphere.
NOTE:
- Override drive parameter: 0%
- Override drive parameter: 100%
|
| EGR_COMD |
% |
- Displays in the M-MDS but it does not operate.
|
| ENG_COOL_VLV_POS_COM D |
°(deg) |
- Changes °(deg) and forcibly drives/stops coolant control valve.
|
- Under the following conditions:
- Ignition is switched ON (engine off)
|
NOTE:
- Override drive parameter: 0-119°
|
| ENG_RPM_DSD |
Rpm |
- Changes value (RPM) to forcibly vary engine speed.
|
- Under the following conditions:
|
- The use in the following ranges is recommended:
- Engine coolant temperature: 75-95 °C {167-203 °F}
- Vehicle speed: 0 km/h {0 mph}
- Override drive parameter input range: 550-2, 000 rpm
|
| EX_SHUT_VLV_DSD |
°(deg) |
- Changes °(deg) and forcibly drives/stops exhaust shutter valve.
|
- Under the following conditions:
- Ignition is switched ON (engine off)
|
NOTE:
- Override drive parameter: 0-66°
|
| FAN |
% |
- Displays in the M-MDS but it does not operate.
|
| FP_DUTY |
% |
- Changes % and forcibly drives/stops fuel pump.
|
- Under the following conditions:
- Ignition is switched ON (engine off)
|
WARNING:
- Do not use the simulation function while the fuel hose between the high pressure fuel pump and fuel pump is removed.
NOTE:
- Override drive parameter: 5-95%
|
| FUEL_PUMP_REQ |
Off/On |
- Select Off/On to forcibly drive/stop the fuel pump.
|
- Under the following conditions:
- Ignition is switched ON (engine off)
- Idle
|
|
| INJ |
- |
- Forcibly stops the fuel injectors while the engine is idling.
|
- Under the following conditions:
|
WARNING:
- Do not use the simulation function while the vehicle is being driven. Stopping the fuel ejection causes the engine to stall which may cause the brakes to not function.
|
| L_SPD_FAN |
Off/On |
- Select Off/On to forcibly drive/stop the cooling fan at low speed.
|
|
|
| H_SPD_FAN |
Off/On |
- Select Off/On to forcibly drive/stop the cooling fan at high speed.
|
|
|
| MIL |
Off/On |
- Select Off/On to turn on/off the check engine light.
|
- Under the following conditions:
- Ignition is switched ON (engine off)
- Idle
|
|
| OIL_PRES_SOL |
Off/On |
- Select Off/On to forcibly drive/stop the engine oil solenoid valve.
|
|
|
| OIL_PUMP_DUTY |
% Duty Cycle |
- Changes % and forcibly drives/stops engine oil solenoid valve.
|
- Under the following conditions:
|
NOTE:
- Override drive parameter: 0-100°
|
| PRG_DUTY |
% |
- Changes % and forcibly drives/stops purge solenoid valve.
|
- Under the following conditions:
- Ignition is switched ON (engine off)
- Idle
|
WARNING:
- Do not open the purge solenoid valve while the CV solenoid valve is forcibly closed. Otherwise, there may be abnormal vacuum in the fuel tank, resulting in damage to the fuel tank.
NOTE:
- Override drive parameter: 0%
- Purge solenoid valve: close
- Override drive parameter: 100%
- Purge solenoid valve: open
|
| WHEEL_DRIVE_CTRL_COMD |
- |
- Forcibly drives/stops AWD solenoid.
|
- Under the following conditions:
- Ignition is switched ON (engine off)
- Idle
|
NOTE:
- If the AWD solenoid is forcibly driven, the AWD warning light flashes.
|