| 1 |
RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION
NOTE:
- Recording can be facilitated using the screen capture function of the PC.
- Record the FREEZE FRAME DATA/snapshot data on the repair order.
|
- |
Go to the next step. |
| 2 |
VERIFY RELATED REPAIR INFORMATION AVAILABILITY
- Verify related Service Bulletins and/or on-line repair information availability.
- Is any related repair information available?
|
Yes |
Perform repair or diagnosis according to the available repair information.
- If the vehicle is not repaired, go to the next step.
|
| No |
Go to the next step. |
| 3 |
INSPECT BOOST PRESSURE SENSOR/BOOST AIR TEMPERATURE SENSOR CONNECTOR CONDITION
- Switch the ignition off.
- Disconnect the boost pressure sensor/boost air temperature sensor connector.
- Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
- Is there any malfunction?
|
Yes |
Repair or replace the connector and/or terminals, then go to Step 8. |
| No |
Go to the next step. |
| 4 |
INSPECT PCM CONNECTOR CONDITION
- Disconnect the PCM connector.
- Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
- Is there any malfunction?
|
Yes |
Repair or replace the connector and/or terminals, then go to Step 8. |
| No |
Go to the next step. |
| 5 |
INSPECT BOOST PRESSURE SENSOR CIRCUIT FOR SHORT TO GROUND
- Verify that the boost pressure sensor/boost air temperature sensor and PCM connectors are disconnected.
- Inspect for continuity between the following terminals (wiring harness-side) and body ground:
- Boost pressure sensor/boost air temperature sensor terminal C
- Boost pressure sensor/boost air temperature sensor terminal D
|
Yes |
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
- Boost pressure sensor/boost air temperature sensor terminal C-PCM terminal 2AE
- Boost pressure sensor/boost air temperature sensor terminal D-PCM terminal 2AS
If there is a common connector:
- Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.
- Repair or replace the malfunctioning part.
If there is no common connector:
- Repair or replace the wiring harness which has a short to ground.
Go to Step 8. |
| No |
Go to the next step. |
| 6 |
INSPECT BOOST PRESSURE SENSOR SIGNAL CIRCUIT AND GROUND CIRCUIT FOR SHORT TO EACH OTHER
- Verify that the boost pressure sensor/boost air temperature sensor and PCM connectors are disconnected.
- Inspect for continuity between boost pressure sensor/boost air temperature sensor terminals D and A (wiring harness-side).
- Is there continuity?
|
Yes |
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
- Boost pressure sensor/boost air temperature sensor terminal D-PCM terminal 2AS
- Boost pressure sensor/boost air temperature sensor terminal A-PCM terminal 2J
If there is a common connector:
- Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to each other.
- Repair or replace the malfunctioning part.
If there is no common connector:
- Repair or replace the wiring harness which has a short to each other.
Go to Step 8. |
| No |
Go to the next step. |
| 7 |
INSPECT BOOST PRESSURE SENSOR
|
Yes |
Replace the boost pressure sensor/boost air temperature sensor, then go to the next step.
(See BOOST PRESSURE SENSOR/BOOST AIR TEMPERATURE SENSOR REMOVAL/INSTALLATION
.) |
| No |
Go to the next step. |
| 8 |
VERIFY DTC TROUBLESHOOTING COMPLETED
- Always reconnect all disconnected connectors.
- Clear the DTC from the PCM memory using the M-MDS. (See CLEARING DTC
.)
- Perform the KOEO or KOER self test. (See KOEO/KOER SELF TEST
.)
- Is the same DTC present?
|
Yes |
Repeat the inspection from Step 1.
Go to the next step. |
| No |
Go to the next step. |
| 9 |
VERIFY AFTER REPAIR PROCEDURE
|
Yes |
Go to the applicable DTC inspection.
(See DTC TABLE
.) |
| No |
DTC troubleshooting completed. |