Diagnostic Procedure

WARNING: This page is about a different car, the 2018 Mazda CX-5. However, it is still accessible from the selected car via links, so may be relevant.

WARNING:

Handling the component parts improperly can accidentally operate (deploy) the air bag modules, pre-tensioner seat belts and lap pre-tensioner seat belts, which may seriously injure you. Read the service warnings/cautions and the applicable service information before handling the air bag system components. (See AIR BAG SYSTEM SERVICE WARNINGS [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.] .) (See AIR BAG SYSTEM SERVICE CAUTIONS [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.] .)

DTC U3003:16/U3003:17 (SAS Control Module (Two-step Deployment Control System - US/Canada Spec.)) DIAGNOSTIC PROCEDURE

Step	Inspection		Action
1	INSPECT IG1 RELAY Switch the ignition off. Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION .) Remove the IG1 relay. (See RELAY LOCATION .) Inspect the IG1 relay. (See RELAY INSPECTION .) Is the IG1 relay normal?	Yes	Go to the next step.
		No	Replace the IG1relay, then go to Step 8.
2	INSPECT PCM DTC Perform the PCM DTC inspection using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION))] .) Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [PCM (SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION))] .)
		No	Go to the next step.
3	INSPECT BATTERY Inspect the battery. (See BATTERY INSPECTION .) Is the battery normal?	Yes	Go to the next step.
		No	Replace or charge the battery. (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION)] .) (See BATTERY RECHARGING .) Then go to Step 8.
4	INSPECT GENERATOR Inspect the generator. (See GENERATOR INSPECTION [SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION)] .) Is the generator normal?	Yes	Go to the next step.
		No	Replace the generator, then go to Step 8. (See GENERATOR REMOVAL/INSTALLATION [SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION)] .)
5	VERIFY SAS CONTROL MODULE CONNECTOR CONDITION Switch the ignition off. Disconnect the negative battery terminal and wait for 1 min or more. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION .) Remove the column cover. (See COLUMN COVER REMOVAL/INSTALLATION .) Disconnect the clock spring connector. (See CLOCK SPRING REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.] .) Remove the glove compartment. (See GLOVE COMPARTMENT REMOVAL/INSTALLATION .) Disconnect the passenger-side air bag module connectors. (See PASSENGER-SIDE AIR BAG MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.] .) Disconnect the driver and passenger-side front seat connectors. (See FRONT SEAT REMOVAL/INSTALLATION .) Remove the B-pillar lower trim. (See B-PILLAR LOWER TRIM REMOVAL/INSTALLATION .) Disconnect the driver and passenger-side pre-tensioner seat belt connectors. (See FRONT SEAT BELT REMOVAL/INSTALLATION .) Disconnect the driver and passenger-side lap pre-tensioner seat belt connectors. (See FRONT SEAT BELT REMOVAL/INSTALLATION .) Remove the headliner. (See HEADLINER REMOVAL/INSTALLATION .) Disconnect the driver and passenger-side curtain air bag module connectors. (See CURTAIN AIR BAG MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.] .) Disconnect the all SAS control module connectors. (See SAS CONTROL MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.] .) Inspect the connector and terminals (corrosion, damage, pin disconnection). Are the connector and terminals normal?	Yes	Go to the next step.
		No	Replace the air bag harness. After repair procedure, go to Step 8.
6	INSPECT SAS CONTROL MODULE POWER SUPPLY VOLTAGE SAS control module connectors are disconnected. Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION .) Switch the ignition on (engine off or on). Measure the voltage at the following terminal (wiring harness-side): SAS control module terminal 2AD Is the voltage 8.1-15.9?	Yes	Go to the next step.
		No	Inspect the SRS1 7.5 A fuse and MAIN 200 A fuse. If the fuse is blown: Refer to the wiring diagram and verify whether or not there is a common connector between MAIN 200 A fuse and SAS control module terminal 2AD. If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has a short to ground. Replace the fuse. If the fuse is damaged: Replace the fuse. If the fuse is normal: Refer to the wiring diagram and verify whether or not there is a common connector between battery positive terminal and SAS control module terminal 2AD. If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has an open circuit. Go to Step 8.
7	INSPECT SAS CONTROL MODULE BODY GROUND CIRCUIT FOR OPEN CIRCUIT SAS control module connectors are disconnected. Switch the ignition off. Disconnect the negative battery terminal and wait 1 min or more. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION .) Inspect for continuity between the following terminals (wiring harness-side) and body ground: SAS control module terminal 2X SAS control module terminal 2AB NOTE: Inspect for continuity while shaking the wiring harness between the SAS control module and body ground. Is there continuity?	Yes	Go to the next step.
		No	Refer to the wiring diagram and verify whether or not there is a common connector between SAS control module terminal and body ground. If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit. Replace the malfunctioning part. If there is no common connector: Replace the wiring harness which has an open circuit. Go to the next step.
8	PERFORM SAS CONTROL MODULE DTC INSPECTION Connect the SAS control module connectors. Reconnect all disconnected connectors. Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION .) Switch the ignition ON (engine off or on). Clear the DTC for the SAS control module using the M-MDS. (See CLEARING DTC (SAS Control Module (Two-step Deployment Control System - US/Canada Spec.)) .) Perform the DTC inspection for the SAS control module using the M-MDS. (See DTC INSPECTION (SAS Control Module (Two-step Deployment Control System - US/Canada Spec.)) .) Are the same DTCs present?	Yes	Repeat the inspection from Step 1. If the malfunction recurs, replace the SAS control module. (See SAS CONTROL MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.] .)
		No	DTC troubleshooting completed.