| 1 |
VERIFY IF MALFUNCTION CAUSE IS OPERATION UNDER OPERATION PERMISSION CONDITION
- Perform the power window system initialization procedure.
- Does the passenger-side door glass operate automatically using the power window sub switch?
|
Yes |
System is normal. (Tell the customer about power window system initialization procedure). |
| No |
Go to the next step. |
| 2 |
POWER WINDOW SUB SWITCH CONNECTOR INSPECTION
- Switch the ignition off.
- Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION
).
- Disconnect the power window sub switch connector.
- Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
- Is the connector normal?
|
Yes |
Go to the next step. |
| No |
Repair or replace the connector, then go to Step 10. |
| 3 |
POWER WINDOW MOTOR (RH) CONNECTOR INSPECTION
- Disconnect the power window motor (RH) connector.
- Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
- Is the connector normal?
|
Yes |
Go to the next step. |
| No |
Repair or replace the connector, then go to Step 10. |
| 4 |
POWER WINDOW MOTOR (RH) TERMINAL D INSPECTION
- Reconnect all the disconnected connectors.
- Connect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION
).
- Measure the voltage at the power window motor (RH) terminal D (vehicle wiring harness side).
- Is the voltage B+?
|
Yes |
Go to Step 6. |
| No |
Go to the next step. |
| 5 |
POWER WINDOW SUB SWITCH TERMINAL J INSPECTION
- Measure the voltage at power window sub switch terminal J (vehicle wiring harness side).
- Is the voltage B+?
|
Yes |
Refer to the wiring diagram and verify if there is a common connector between power window sub switch terminal J and power window motor (RH) terminal D.
If there is a common connector:
- Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for an open or short circuit to determine the malfunctioning location.
- Repair or replace the malfunctioning location.
If there is no common connector:
- Repair or replace the wiring harness which has an open or short circuit.
Go to Step 10. |
| No |
Replace the power window sub switch, then go to Step 10. (See POWER WINDOW SUBSWITCH REMOVAL/INSTALLATION
). |
| 6 |
DETERMINE IF MALFUNCTION CAUSE IS POWER WINDOW SUB SWITCH INTERNAL GROUND SYSTEM
|
Yes |
Go to Step 8. |
| No |
Go to the next step. |
| 7 |
VERIFY IF MALFUNCTION CAUSE IS OPEN CIRCUIT IN WIRING HARNESS BETWEEN POWER WINDOW SUB SWITCH AND POWER WINDOW MOTOR (RH)
- Disconnect the power window sub switch connector and power window motor (RH) connector.
- Inspect for continuity between the following terminals (vehicle wiring harness).
- Power window sub switch terminal L and power window motor (RH) terminal H
- Is there continuity?
|
Yes |
Replace the power window sub switch, then go to Step 10. (See POWER WINDOW SUBSWITCH REMOVAL/INSTALLATION
). |
| No |
Refer to the wiring diagram and verify if there is a common connector between power window sub switch terminal L and power window motor (RH) terminal H.
If there is a common connector:
- Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for an open circuit to determine the malfunctioning location.
- Repair or replace the malfunctioning location.
If there is no common connector:
- Repair or replace the wiring harness which has an open circuit.
Go to Step 10. |
| 8 |
POWER WINDOW SUB SWITCH TERMINALS D AND E INSPECTION
- Reconnect all the disconnected connectors.
- Connect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION
).
- Switch the ignition ON (engine off or on).
- Operate the passenger-side power window to measure the pulse at power window sub switch terminals D and E.
- Measure the pulse at power window sub switch terminals D and E. (See INSPECTION USING AN OSCILLOSCOPE ).
- Is the pulse normal?
|
Yes |
NOTE:
- The power window motor (RH) is normal because the pulse sent from the power window motor (RH) to the power window sub switch is normal.
Replace the power window sub switch, then go to Step 10. (See POWER WINDOW SUBSWITCH REMOVAL/INSTALLATION
). |
| No |
Go to the next step. |
| 9 |
POWER WINDOW MOTOR (RH) TERMINALS B AND F INSPECTION
- Operate the passenger-side power window to measure the pulse at power window motor (RH) terminals B and F. (See INSPECTION USING AN OSCILLOSCOPE ).
- Is the pulse normal?
|
Yes |
Refer to the wiring diagram and verify if there is a common connector between the following terminals.
- Power window sub switch terminal D and power window motor (RH) terminal B
- Power window sub switch terminal E and power window motor (RH) terminal F
If there is a common connector:
- Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for an open or short circuit to determine the malfunctioning location.
- Repair or replace the malfunctioning location.
If there is no common connector:
- Repair or replace the wiring harness which has an open or short circuit.
Go to the next step. |
| No |
Replace the power window motor (RH), then go to the next step. (See POWER WINDOW REGULATOR DISASSEMBLY/ASSEMBLY
). |
| 10 |
VERIFY IF MALFUNCTION CAUSE IS CORRECTED
- Does the power window system operate normally?
|
Yes |
Troubleshooting completed. (Explain the problem to the customer). |
| No |
Verify the malfunction symptom in the symptom troubleshooting chart and perform the other applicable malfunction diagnosis. |