Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Mazda >> 2017 >> 6 Touring, Automatic Trans >> Repair and Diagnosis >> Body & Frame >> Door Locks >> On-Board Diagnostic - Start Stop Unit >> DTC Table [Start Stop Unit]

DTC Table [Start Stop Unit]

Immobilizer System

x: Applicable -: Not applicable

DTC KEY warning light (red)(3) Push button start indicator light (amber) Description Fail-safe function Drive cycle Self test type(2) Memory function Service Information
M-MDS display(1)      
Start stop unit     PCM
U3000:96 P1260:00 09
G11543433
 On Flash Start stop unit malfunction - - C x (See SECURITY INDICATOR LIGHT: 09, DTC: U3000:96/P1260:00 [START STOP UNIT] .)
B10D9:87 P1260:00 11
G11543434
 - Flash Coil antenna (built into push button start) error - - C - (See SECURITY INDICATOR LIGHT: 11, DTC: B10D9:87/P1260:00 [START STOP UNIT] .)
B13D3:05 P1260:00 13
G11543435
 - - Remote transmitter program error - - C - (See SECURITY INDICATOR LIGHT: 13, DTC: B13D3:05/P1260:00 [START STOP UNIT] .)
B13D3:94 P1260:00 13   - - Communication error with remote transmitter - - C - (See SECURITY INDICATOR LIGHT: 13, DTC: B13D3:94/P1260:00 [START STOP UNIT] .)
B13D3:51 P1260:00 15
G11543436
 - Flash Unregistered remote transmitter is detected - - C - (See SECURITY INDICATOR LIGHT: 15, DTC: B13D3:51/P1260:00 [START STOP UNIT] .)
U0100:87 P1260:00 16
G11543437
 - - Communication error with PCM (no response or data mismatch) - - C - (See SECURITY INDICATOR LIGHT: 16, DTC: U0100:87/P1260:00 [START STOP UNIT] .)
B13D4:00 P1260:00 21
G11543438
 On - Insufficient remote transmitter programming number - - C - (See SECURITY INDICATOR LIGHT: 21, DTC: B13D4:00/P1260:00 [START STOP UNIT] .)
B10DA:51 P1260:00 22
G11543439
 - - Communication error with PCM (data received failure) - - C - (See SECURITY INDICATOR LIGHT: 22, DTC: B10DA:51/P1260:00 [START STOP UNIT] .)
B10DA:62 P1260:00 23
G11543440
 - - Communication error with PCM (code mis-matched) - - C - (See SECURITY INDICATOR LIGHT: 23, DTC: B10DA:62/P1260:00 [START STOP UNIT] .)
(1) The letters at the beginning of each DTC are only displayed when using the M-MDS, and refer to the following: B= Body system, P= Powertrain system, U= Network communication system.
(2) C: CMDTC self test, D: ODDTC self test
(3) Type B instrument cluster

Advanced Keyless Entry System (With Advanced Keyless Entry System)

x: Applicable -: Not applicable

DTC No. KEY warning light (red)(2) Description Fail-safe function Drive cycle Self test type(1) Memory function Service Information
B10C6:1F On Keyless antenna (exterior, rear) circuit malfunction x - C, D x (See DTC B10C6:1F [START STOP UNIT] .)
B10C7:1F On Keyless antenna (interior, rear) circuit malfunction x - C, D x (See DTC B10C7:1F [START STOP UNIT] .)
B10C9:1F On Keyless antenna (interior, front) circuit malfunction x - C, D x (See DTC B10C9:1F [START STOP UNIT] .)
B10D1:23 On Request switch (LF) circuit malfunction - - C x (See DTC B10D1:23 [START STOP UNIT] .)
B10D3:23 On Request switch (RF) circuit malfunction - - C x (See DTC B10D3:23 [START STOP UNIT] .)
B11FD:1F On Keyless antenna (exterior, LF) circuit malfunction x - C, D x (See DTC B11FD:1F [START STOP UNIT] .)
B1210:1F On Keyless antenna (exterior, RF) circuit malfunction x - C, D x (See DTC B1210:1F [START STOP UNIT] .)
B13C3:04 On LF control unit internal malfunction x - C x (See DTC B13C3:04 [START STOP UNIT] .)
B13C3:09 On LF control unit malfunction x - C x (See DTC B13C3:09 [START STOP UNIT] .)
B13C3:16 On LF control unit power supply voltage low input x - C x (See DTC B13C3:16 [START STOP UNIT] .)
B13C3:29 On Communication error between start stop unit and LF control unit x - C x (See DTC B13C3:29 [START STOP UNIT] .)
(1) C: CMDTC self test, D: ODDTC self test
(2) Type B instrument cluster

Start Stop Unit

x: Applicable -: Not applicable

DTC No. KEY warning light (red)(2) Push button start indicator light (amber) Description Fail-safe function Drive cycle Self test type (1) Memory function Service Information
B108B:23 - Flash Push button start switch 1 circuit malfunction x - C x (See DTC B108B:23 [START STOP UNIT] .)
B108B:24 - Flash Push button start switch 1 circuit malfunction - - C x (See DTC B108B:24 [START STOP UNIT] .)
B108C:23 - Flash Push button start switch 2 circuit malfunction x - C x (See DTC B108C:23 [START STOP UNIT] .)
B108C:24 - Flash Push button start switch 2 circuit malfunction - - C x (See DTC B108C:24 [START STOP UNIT] .)
B10AC:13(3) - - Cruise control switch circuit malfunction - - C x (See DTC B10AC:13 [START STOP UNIT] .)
B10AC:23(3) - - Cruise control switch circuit malfunction - - C x (See DTC B10AC:23 [START STOP UNIT] .)
B10C9:1F On - Keyless antenna (interior, center) circuit malfunction (With keyless entry system) - - C, D x (See DTC B10C9:1F [START STOP UNIT] .)
B10E7:11 - Flash IG1 relay circuit malfunction - - C x (See DTC B10E7:11 [START STOP UNIT] .)
B10E7:12 - Flash IG1 relay circuit malfunction - - C x (See DTC B10E7:12 [START STOP UNIT] .)
B10E7:16 - Flash IG1 relay circuit malfunction - - C x (See DTC B10E7:16 [START STOP UNIT] .)
B10E7:17 - Flash IG1 relay circuit malfunction - - C x (See DTC B10E7:17 [START STOP UNIT] .)
B112A:11 - Flash IG2 relay circuit malfunction - - C x (See DTC B112A:11 [START STOP UNIT] .)
B112A:12 - Flash IG2 relay circuit malfunction - - C x (See DTC B112A:12 [START STOP UNIT] .)
B124C:56 - - Turn switch circuit malfunction - - C x (See DTC B124C:56 [START STOP UNIT] .)
B13D3:16 - - Low remote transmitter battery voltage - - C x (See DTC B13D3:16 [START STOP UNIT] .)
B13D3:4A On - Remote transmitter assembly malfunction - - C x (See DTC B13D3:4A [START STOP UNIT] .)
B13D3:97 - - Remote transmitter registration work not completed - - C x (See DTC B13D3:97 [START STOP UNIT] .)
B1C53:13 - - Windshield wiper switch circuit malfunction - - C x (See DTC B1C53:13 [START STOP UNIT] .)
C0040:23(4) - Flash Brake switch (No. 1 signal) circuit malfunction x - C x (See DTC C0040:23 [START STOP UNIT] .)
C0040:24(4) - Flash Brake switch (No. 1 signal) circuit malfunction x - C x (See DTC C0040:24 [START STOP UNIT] .)
C0051:95(5) - - Steering angle sensor assembly malfunction - - C x (See DTC C0051:95 [START STOP UNIT] .)
C0051:2F(5) - - Steering angle sensor signal error - - C x (See DTC C0051:2F [START STOP UNIT] .)
C0052:14(5) - - Steering angle sensor A signal circuit malfunction - - C x (See DTC C0052:14 [START STOP UNIT] .)
C0052:2F(5) - - Steering angle sensor A signal malfunction - - C x (See DTC C0052:2F [START STOP UNIT] .)
C0053:14(5) - - Steering angle sensor B signal circuit malfunction - - C x (See DTC C0053:14 [START STOP UNIT] .)
C0053:2F(5) - - Steering angle sensor B signal malfunction - - C x (See DTC C0053:2F [START STOP UNIT] .)
C2003:13 - - Open circuit in steering switch - - C x (See DTC C2003:13 [START STOP UNIT] .)
P0615:11 - Flash Starter relay circuit malfunction - - C x (See DTC P0615:11 [START STOP UNIT] .)
P0615:12 - Flash Starter relay circuit malfunction x - C x (See DTC P0615:12 [START STOP UNIT] .)
P0615:13 - Flash Starter relay circuit malfunction - - C x (See DTC P0615:13 [START STOP UNIT] .)
P0615:16 - Flash Starter relay circuit malfunction - - C x (See DTC P0615:16 [START STOP UNIT] .)
P0616:23 - - Circuit malfunction on downstream side of starter relay - - C x (See DTC P0616:23 [START STOP UNIT] .)
P0616:24 - - Circuit malfunction on downstream side of starter relay - - C x (See DTC P0616:24 [START STOP UNIT] .)
P0616:29 - - Downstream side of starter relay signal malfunction - - C x (See DTC P0616:29 [START STOP UNIT] .)
P081C:23(4) - Flash NOT P position switch circuit malfunction x - C x (See DTC P081C:23 [START STOP UNIT] .)
P081C:24(4) - Flash NOT P position switch circuit malfunction x - C x (See DTC P081C:24 [START STOP UNIT] .)
P081D:29(6) - Flash Neutral switch error signal receive d x - C x (See DTC P081D:29 [START STOP UNIT] .)
P081D:2F(6) - Flash Neutral switch signal mismatch x - C x (See DTC P081D:2F [START STOP UNIT] .)
P0830:23(6) - Flash CPP switch circuit malfunction x - C x (See DTC P0830:23 [START STOP UNIT] .)
P0850:23(4) - Flash Transaxle range sensor circuit malfunction x - C x (See DTC P0850:23 [START STOP UNIT] .)
P0850:24(4) - Flash Transaxle range sensor circuit malfunction x - C x (See DTC P0850:24 [START STOP UNIT] .)
P0930:71(4) - - Shift-lock solenoid circuit malfunction x - C x (See DTC P0930:71 [START STOP UNIT] .)
P1708:24(6) - Flash Starter interlock switch circuit malfunction x - C x (See DTC P1708:24 [START STOP UNIT] .)
P1708:29(6) - Flash Starter interlock switch circuit or CPP switch circuit malfunction x - C x (See DTC P1708:29 [START STOP UNIT] .)
P1794:16 - Flash Start stop unit power supply voltage (terminal 2W) low input - - C x (See DTC P1794:16 [START STOP UNIT] .)
U0001:88 On Flash Module communication error (HS-CAN) x - C x (See DTC U0001:88/U0100:00/U0101:00/U0121:00/U0121:87/U0131:00/U0140:00/U0146:00/U0151:00/U0155:00 [START STOP UNIT] .)
U0028:87 On - Communication error with rear body control module (RBCM) - - C x (See DTC U0028:87 [START STOP UNIT] .)
U0100:00 On Flash Communication error with PCM x - C x (See DTC U0001:88/U0100:00/U0101:00/U0121:00/U0121:87/U0131:00/U0140:00/U0146:00/U0151:00/U0155:00 [START STOP UNIT] .)
U0101:00(4) - Flash Communication error with TCM x - C x (See DTC U0001:88/U0100:00/U0101:00/U0121:00/U0121:87/U0131:00/U0140:00/U0146:00/U0151:00/U0155:00 [START STOP UNIT] .)
U0121:00 On Flash Communication error with DSC HU/CM x - C x
U0121:87 On Flash Communication error with DSC HU/CM x - C x
U0131:00 - - Communication error with EPS control module x - C x
U0140:00 - - Communication error with front body control module (FBCM) x - C x
U0146:00 On Flash Communication error with instrument cluster x - C x
U0151:00 On Flash Communication error with SAS control module x - C x
U0155:00 On Flash Communication error with instrument cluster x - C x
U0447:86 On Flash Error signal receive d from instrument cluster x - C x (See DTC U0447:86 [START STOP UNIT] .)
U201F:11 On - Keyless receive r circuit malfunction - - C x (See DTC U201F:11 [START STOP UNIT] .)
U201F:12 On - Keyless receive r circuit malfunction - - C x (See DTC U201F:12 [START STOP UNIT] .)
U2100:00 On - Start stop unit configuration not completed x - C x (See DTC U2100:00 [START STOP UNIT] .)
U2300:00 - - Configuration data not receive d from instrument cluster x - C x (See DTC U2300:00 [START STOP UNIT] .)
U3000:01(5) - - Start stop unit internal malfunction - - C x (See DTC U3000:01 [START STOP UNIT] .)
U3000:49 On Flash Start stop unit internal malfunction x - C x (See DTC U3000:49 [START STOP UNIT] .)
U3000:96 On Flash Start stop unit malfunction - - C x (See DTC U3000:96 [START STOP UNIT] .)
U3003:16 On - Start stop unit power supply voltage (terminal 1A) low input x - C x (See DTC U3003:16 [START STOP UNIT] .)
U3004:11 - Flash ACC relay circuit malfunction - - C x (See DTC U3004:11 [START STOP UNIT] .)
U3004:12 - Flash ACC relay circuit malfunction - - C x (See DTC U3004:12 [START STOP UNIT] .)
U3004:16 - - ACC relay circuit malfunction - - C x (See DTC U3004:16 [START STOP UNIT] .)
U3004:17 - - ACC relay circuit malfunction - - C x (See DTC U3004:17 [START STOP UNIT] .)
(1) C: CMDTC self test, D: ODDTC self test
(2) Type B instrument cluster
(3) With cruise control system
(4) ATX
(5) With AFS, smart city brake support (SCBS), or blind spot monitoring (BSM) system
(6) MTX
scientia non olet · About Mike's Workshop Manuals