Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Mazda >> 2016 >> 3 Sport, 4D Hatchback, Automatic Trans >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> On-Board Diagnostic - Two-Step Deployment Control System >> PID Data Monitor Table

PID Data Monitor Table

PID Unit/Condition Data contents SAS control module terminal (Type A) SAS control module terminal (Type B)
AB_WL
(Air bag system warning light status)		 Lamp_Off/Lamp_On/Plant_Mode/Unknown
  • Air bag system warning light off: Lamp_Off
  • Air bag system warning light on: Lamp_On
  • Air bag system warning light status: Plant_Mode
  • Air bag system warning light status: Unknown
 3K, 3L 3B, 3C
B_SW_P_FLT
(Passenger-side buckle switch malfunction status)		 O.K./FAULT
  • Passenger-side buckle switch normal: O.K.
  • Passenger-side buckle switch abnormal: Fault
 2B 2P
OCS_DTC_CLR
(Seat weight sensor DTC cleared status)		 Starting/Normal End/In Process/OCS Fault Fault information cleared at seat weight sensor 2B 2P
P_OCS_S
(Seat weight sensor status)		 Empty/SMALL/Indeterminate/LARGE Occupant classification status determined by seat weight sensor 2B 2P
P_WEIGHT
(Seat weight sensor measured weight of passenger)		 Kg Display of load (body weight) on passenger-side seat 2B 2P
RES_C_AB_D
(Driver-side curtain air bag module resistance nominal)		 ohm Continuous: 0.81-6.42 ohms  1S, 1V 1G, 1C
RES_C_AB_P
(Passenger-side curtain air bag module resistance nominal)		 ohm Continuous: 0.81-6.42 ohms  1W, 1T 1K, 1N
RES_F_AB1_D
(Driver-side air bag module (inflator No. 1) resistance nominal)		 ohm Continuous: 0.99-6.42 ohms  3A, 3D 3J, 3H
RES_F_AB1_P
(Passenger-side air bag module (inflator No. 1) resistance nominal)		 ohm Continuous: 0.81-6.42 ohms  3G, 3J 3L, 3M
RES_F_AB2_D
(Driver-side air bag module (inflator No. 2) resistance nominal)		 ohm Continuous: 0.99-6.42 ohms  3S, 3V 3P, 3O
RES_F_AB2_P
(Passenger-side air bag module (inflator No. 2) resistance nominal)		 ohm Continuous: 0.81-6.42 ohms  3T, 3W 3F, 3G
RES_PCD_BAR
(Poorly connected detector bar terminals resistance nominal (all of SAS control module connectors)		 ohm
  • Normal connected: 100 ohm or less 
  • Poor connected: 20 kilohm or more 
 1a, 1b,
2a, 2b,
3a, 3b		 1a, 1b,
2a, 2b,
3a, 3b
RES_S_AB_D
(Driver-side side air bag module resistance nominal)		 ohm Continuous: 0.81-9.85 ohms  1A, 1D 1B, 1D
RES_S_AB_P
(Passenger-side side air bag module resistance nominal)		 ohm Continuous: 0.81-9.85 ohms  1J, 1G 1F, 1H
RES_SB_LP_D
(Driver-side lap pre-tensioner seat belt resistance nominal)		 ohm Continuous: 0.81-6.42 ohms  2V, 2S 2AF, 2AD
RES_SB_LP_P
(Passenger-side lap pre-tensioner seat belt resistance nominal)		 ohm Continuous: 0.81-6.42 ohms  2Y, 2AB 2U 2W
RES_SB_P_D
(Driver-side pre-tensioner seat belt resistance nominal)		 ohm Continuous: 0.81-6.42 ohms  2D, 2A 2AB, 2Z
RES_SB_P_P
(Passenger-side pre-tensioner seat belt resistance nominal)		 ohm Continuous: 0.81-6.42 ohms  2G, 2J 2Q, 2O
SEAT_B_D
(Driver-side buckle switch status)		 Unbuckled/Buckled
  • Driver-side front seat belt fastened (Driverside buckle switch off): Buckled
  • Driver-side front seat belt not fastened (Driver-side buckle switch on): Unbuckled
 2U 2N
SEAT_B_P
(Passenger-side buckle switch status)		 Unbuckled/Buckled Occupant seated in passenger-side front seat: On
  • Passenger-side front seat belt fastened (Passenger-side buckle switch off): Buckled
  • Passenger-side front seat belt not fastened (Passenger-side buckle switch on): Unbuckled
 2B 2P
VPWR_IGA
(SAS control module power voltage)		 V Ignition is switched ON: IG1 voltage 3C 3AD
scientia non olet · About Mike's Workshop Manuals