Diagnostic Procedure

DTC P0533:00 (SKYACTIV-G 2.0, SKYACTIV-G 2.5) - DIAGNOSTIC PROCEDURE

STEP	INSPECTION		ACTION
1	VERIFY RELATED REPAIR INFORMATION AVAILABILITY Verify related Service Bulletins and/or on-line repair information availability. Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information. If the vehicle is not repaired, go to the next step.
1		No	Go to the next step.
2	DETERMINE IF REFRIGERANT PRESSURE SENSOR OR WIRING HARNESS MALFUNCTION Access the AC PRES PID using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Verify the AC_PRES PID value. Is the AC_PRES PID value 5 V or B+ ?	Yes	Go to Step 6.
2		No	Go to the next step.
3	INSPECT REFRIGERANT PRESSURE SENSOR CONNECTOR CONDITION Switch the ignition off. Disconnect the refrigerant pressure sensor connector. Inspect for poor connection (such as damaged/pulled-out pins, corrosion). Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 9.
3		No	Go to the next step.
4	INSPECT PCM CONNECTOR CONDITION Disconnect the PCM connector. Inspect for poor connection (such as damaged/pulled-out pins, corrosion). Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 9.
4		No	Go to the next step.
5	INSPECT REFRIGERANT PRESSURE SENSOR Reconnect all disconnected connectors. Inspect the refrigerant pressure sensor. (See REFRIGERANT PRESSURE SENSOR INSPECTION [MANUAL AIR CONDITIONER] .) (See REFRIGERANT PRESSURE SENSOR INSPECTION [FULL-AUTO AIR CONDITIONER] .) Is there any malfunction?	Yes	Replace the refrigerant pressure sensor, then go to Step 9. (See REFRIGERANT PRESSURE SENSOR REMOVAL/INSTALLATION [MANUAL AIR CONDITIONER] .) (See REFRIGERANT PRESSURE SENSOR REMOVAL/INSTALLATION [FULL-AUTO AIR CONDITIONER] .)
5		No	Go to Step 9.
6	DETERMINE IF REFRIGERANT PRESSURE SENSOR SIGNAL CIRCUIT OR REFRIGERANT PRESSURE SENSOR GROUND CIRCUIT MALFUNCTION Switch the ignition off. Disconnect the refrigerant pressure sensor connector. Access the AC_PRES PID using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Verify the AC_PRES PID value. Is the AC_PRES PID value 5 V or B+ ?	Yes	Go to the next step.
6		No	Go to Step 8.
7	INSPECT REFRIGERANT PRESSURE SENSOR SIGNAL CIRCUIT FOR OPEN CIRCUIT Verify that the refrigerant pressure sensor connector is disconnected. Switch the ignition off. Disconnect the PCM connector. Inspect for continuity between refrigerant pressure sensor terminal B (wiring harness-side) and PCM terminal 2AX (wiring harness-side). Is there continuity?	Yes	Refer to the wiring diagram and verify whether or not there is a common connector between refrigerant pressure sensor terminal B and PCM terminal 2AX. If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to power supply. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has a short to power supply. Go to Step 9.
7		No	Refer to the wiring diagram and verify whether or not there is a common connector between refrigerant pressure sensor terminal B and PCM terminal 2AX. If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has an open circuit. Go to Step 9.
8	INSPECT REFRIGERANT PRESSURE SENSOR GROUND CIRCUIT FOR OPEN CIRCUIT Verify that the refrigerant pressure sensor connector is disconnected. Switch the ignition off. Disconnect the PCM connector. Inspect for continuity between refrigerant pressure sensor terminal C (wiring harness-side) and PCM terminal 2AJ (wiring harness-side). Is there continuity?	Yes	Replace the refrigerant pressure sensor, then go to the next step. (See REFRIGERANT PRESSURE SENSOR REMOVAL/INSTALLATION [MANUAL AIR CONDITIONER] .) (See REFRIGERANT PRESSURE SENSOR REMOVAL/INSTALLATION [FULL-AUTO AIR CONDITIONER] .)
8		No	Refer to the wiring diagram and verify whether or not there is a common connector between refrigerant pressure sensor terminal C and PCM terminal 2AJ. If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has an open circuit. Go to the next step.
9	VERIFY DTC TROUBLESHOOTING COMPLETED Always reconnect all disconnected connectors. Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Perform the KOEO or KOER self test. (See KOEO/KOER SELF TEST [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Is the same DTC present?	Yes	Repeat the inspection from Step 1. If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Go to the next step.
9		No	Go to the next step.
10	VERIFY AFTER REPAIR PROCEDURE Perform the "AFTER REPAIR PROCEDURE". (See AFTER REPAIR PROCEDURE [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .)
10		No	DTC troubleshooting completed.