Common Specs & Procedures Index
MAZDA 2 COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | HVAC TECHNICAL DATA | ||
| Torque | See Torque Specifications in Text and applicable graphics in HVAC BASIC SYSTEM | ||
| Axle Nut/Hub Nut | 235-274 N.m (25-27 kgf.m, 175-202 ft.lbf) | ||
| Battery | BATTERY INSPECTION [MZR 1.5] | ||
| Brakes | |||
| Bleeding Sequence | N/A | ||
| Disc Brakes | |||
| Service Specifications | BRAKES TECHNICAL DATA | ||
| Torque | See Torque Specifications in Text and applicable graphics in FRONT BRAKE (DISC) REMOVAL/INSTALLATION | ||
| Drum Brakes | |||
| Service Specifications | BRAKES TECHNICAL DATA | ||
| Torque | See Torque Specifications in Text and applicable graphics in REAR BRAKE (DRUM) REMOVAL/INSTALLATION | ||
| Charging | |||
| Generator | GENERATOR INSPECTION [MZR 1.5] | ||
| Torque | See Torque Specifications in Text and applicable graphics in GENERATOR REMOVAL/INSTALLATION [MZR 1.5] | ||
| Drive Belts | |||
| Adjustment | DRIVE BELT AUTO TENSIONER INSPECTION [MZR 1.5] | ||
| Drive Belt Routing | See illustration under DRIVE BELT REMOVAL/INSTALLATION [MZR 1.5] | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM [MZR 1.5] | ||
| Radiator Cap Pressure | 13.6-17.7 psi | ||
| Thermostat R & I | THERMOSTAT REMOVAL/INSTALLATION [MZR 1.5] | ||
| Water Pump R & I | WATER PUMP REMOVAL/INSTALLATION [MZR 1.5] | ||
| Engine Mechanical | |||
| 1.5 L 4-Cyl. | |||
| Compression | COMPRESSION INSPECTION [MZR 1.5] | ||
| Oil Pressure | Oil Temperature: 100 °C (212 °F) 330-380 kPa {3.37-3.87 kgf/cm2 , 47.9-55.1 psi} [3,000 RPM] | ||
| Overhaul | ENGINE TECHNICAL DATA [MZR 1.5] | ||
| Torque | See torque specifications in Text and applicable graphics in ENGINE MECHANICAL [MZR 1.5] and ENGINE MECHANICAL - OVERHAUL - 1.5L (MZR) | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 97-103 N.m {9.95-10.0 kgf.m, 72-75 ft.lbf} | ||
| Fuel System | |||
| Pressure Specification | 375-450 kPa {3.57-4.18 kgf/cm2 , 50.8-59.4 psi} | ||
| Fuel Pressure Test Procedure | FUEL LINE PRESSURE INSPECTION [MZR 1.5] | ||
| Fuel Filter R & I | FUEL PUMP UNIT REMOVAL/INSTALLATION [MZR 1.5] | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | The 1.5L engine is equipped with coil-on plug ignition. | ||
| Ignition Wires (Routing) | The 1.5L engine is equipped with coil-on plug ignition. | ||
| Spark Plug | |||
| ZJY6-18110, | |||
| Gap | Standard: 1.2-1.4 mm {0.047-0.055 in} New spark plug (reference): 1.2-1.3 mm {0.047-0.051 in} |
||
| Torque | 15-22 N.m {1.6-2.2 kgf.cm, 12-16 ft.lbf} | ||
| Z6B7-18110 | |||
| Gap | Standard: 1.2-1.3 mm {0.047-0.051 in} | ||
| Torque | 15-22 N.m {1.6-2.2 kgf.cm, 12-16 ft.lbf} | ||
| Starting | |||
| Starter | STARTER INSPECTION [MZR 1.5] | ||
| Torque | See Torque Specifications in Text and applicable graphics in STARTER REMOVAL/INSTALLATION [MZR 1.5] | ||
| Wheel Alignment | |||
| Adjustment Specifications | SUSPENSION TECHNICAL DATA | ||
| Torque | See Torque Specifications in Text and applicable graphics in WHEEL ALIGNMENT SYSTEM | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 88-118 N.m {9.0-12 kgf.m, 65-87 ft.lbf} | ||