Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Mazda >> 2007 >> 6 Mazdaspeed >> Repair and Diagnosis >> Brakes >> Traction Control >> On-Board Diagnostic (Abs/TCS) >> Abs/TCS On-Board Diagnosis >> PID/DATA Monitor Table

PID/DATA Monitor Table

PID/DATA MONITOR CHART

PID Name (Definition) Unit/Condition Condition/Specification Action ABS/TCS HU/CM terminal
RPM
(Engine speed signal, input)		 RPM
  • Engine is stopped: 0 RPM 
  • Engine is running:

    Indicates engine speed

 Inspect PCM.
(See PCM INSPECTION [L3] ).
(See PCM INSPECTION [AJ] ).		 -
CCNTABS
(Number of continuous codes)		 -
  • DTC is detected: 1-255 
  • DTC is not detected: 0 
 Perform inspection using appropriate DTC. -
PMPSTAT
(Pump motor output state)		 On/Off
  • Pump motor is activated: On
  • Pump motor is deactivated: Off
 Inspect ABS/TCS HU/CM.
(See ABS/TCS HU/CM SYSTEM INSPECTION ).		 -
BOO_ABS
(Brake pedal switch input)		 On/Off
  • Brake pedal is depressed: On
  • Brake pedal is released: Off
 Inspect brake switch. -
ABS_LAMP
(ABS warning light driver output state)		 On/Off
  • ABS warning light is illuminated: On
  • ABS warning light is not illuminated: Off
 Inspect ABS warning light. -
BRAKE_MP
(BRAKE system warning light output state)		 On/Off
  • BRAKE system warning light is illuminated: On
  • BRAKE system warning light is not illuminated: Off
 Inspect BRAKE system warning light. -
ABSRR_O
(Right rear ABS pressure reduction solenoid valve output state)		 On/Off
  • During ABS or EBD control: On/Off

    (solenoid valve is activated/deactivated)

  • No ABS and EBD control: Off

    (solenoid valve is deactivated)

 Internal fault of ABS/TCS HU/CM. Replace ABSATCS HU/CM.
(See ABS/TCS HU/CM REMOVAL/INSTALLATION ).		 -
ABSLR_O
(Left rear ABS pressure reduction solenoid valve output state)		 On/Off
  • During ABS or EBD control: On/Off

    (solenoid valve is activated/deactivated)

  • No ABS and EBD control: Off

    (solenoid valve is deactivated)

 Internal fault of ABS/TCS HU/CM. Replace ABS/TCS HU/CM.
(See ABS/TCS HU/CM REMOVAL/INSTALLATION ).		 -
ABSRF_O
(Right front ABS pressure reduction solenoid valve output state)		 On/Off
  • During ABS control: On/Off

    (solenoid valve is activated/deactivated)

  • No ABS control: Off

    (solenoid valve is deactivated)

 Internal fault of ABS/TCS HU/CM. Replace ABS/TCS HU/CM.
(See ABS/TCS HU/CM REMOVAL/INSTALLATION ).		 -
ABSLF_O
(Left front ABS pressure reduction solenoid valve output state)		 On/Off
  • During ABS control: On/Off

    (solenoid valve is activated/deactivated)

  • No ABS control: Off

    (solenoid valve is deactivated)

 Internal fault of ABS/TCS HU/CM. Replace ABS/TCS HU/CM.
(See ABS/TCS HU/CM REMOVAL/INSTALLATION ).		 -
ABSRR_I
(Right rear ABS pressure retention solenoid valve output state)		 On/Off
  • During ABS or EBD control: On/Off

    (solenoid valve is activated/deactivated)

  • No ABS and EBD control: Off

    (solenoid valve is deactivated)

 Internal fault of ABS/TCS HU/CM. Replace ABS/TCS HU/CM.
(See ABS/TCS HU/CM REMOVAL/INSTALLATION ).		 -
ABSLR_I
(Left rear ABS pressure retention solenoid valve output state)		 On/Off
  • During ABS or EBD control: On/Off

    (solenoid valve is activated/deactivated)

  • No ABS and EBD control: Off

    (solenoid valve is deactivated)

 Internal fault of ABS/TCS HU/CM. Replace ABS/TCS HU/CM.
(See ABS/TCS HU/CM REMOVAL/INSTALLATION ).		 -
ABSRF_I
(Right front ABS pressure retention solenoid valve output state)		 On/Off
  • During ABS control: On/Off

    (solenoid valve is activated/deactivated)

  • No ABS control: Off

    (solenoid valve is deactivated)

 Internal fault of ABS/TCS HU/CM. Replace ABS/TCS HU/CM.
(See ABS/TCS HU/CM REMOVAL/INSTALLATION ).		 -
ABSLF_I
(Left front ABS pressure retention solenoid valve output state)		 On/Off
  • During ABS control: On/Off

    (solenoid valve is activated/deactivated)

  • No ABS control: Off

    (solenoid valve is deactivated)

 Internal fault of ABS/TCS HU/CM. Replace ABS/TCS HU/CM.
(See ABS/TCS HU/CM REMOVAL/INSTALLATION ).		 -
ABSVLVRLY
(Fail-safe relay output state)		 On/Off
  • Fail-safe relay is activated: On
  • Fail-safe relay is deactivated: Off
 Inspect ABS/TCS HU/CM.
(See ABS/TCS HU/CM INSPECTION )		 -
ABSPMPRLY
(Motor relay output state)		 On/Off
  • Motor relay is activated: On
  • Motor relay is deactivated: Off
 Inspect ABS/TCS HU/CM.
(See ABS/TCS HU/CM INSPECTION )		 -
LF_WSPD
(Left front ABS wheel-speed sensor input)		 KPH, MPH
  • Vehicle is stopped: 0 KPH {0 MPH} 
  • Vehicle is driving: Indicates vehicle speed
 Inspect ABS wheel-speed sensor/sensor rotor. I, E
RF_WSPD
(Right front ABS wheel-speed sensor input)		 KPH, MPH
  • Vehicle is stopped: 0 KPH {0 MPH} 
  • Vehicle is driving: Indicates vehicle speed
 Inspect ABS wheel-speed sensor/sensor rotor. G, D
LR_WSPD
(Left rear ABS wheel-speed sensor input)		 KPH, MPH
  • Vehicle is stopped: 0 KPH {0 MPH} 
  • Vehicle is driving: Indicates vehicle speed
 Inspect ABS wheel-speed sensor/sensor rotor. C, F
RR_WSPD
(Right rear ABS wheel-speed sensor input)		 KPH, MPH
  • Vehicle is stopped: 0 KPH {0 MPH} 
  • Vehicle is driving: Indicates vehicle speed
 Inspect ABS wheel-speed sensor/sensor rotor. A, B
ABS_VOLT
(System battery voltage value)		 V
  • Ignition key at ON: B+ 
  • Idle: Approx. 14-16 V 
 Inspect power supply circuit.
(See ABS/TCS HU/CM INSPECTION ).		 Z
PCM_MSG
(Missing message from the PCM)		 Present/Not Present
  • Present: Circuit in the PCM is normal.
  • Not Present: Circuit in the PCM is abnormal.
 Inspect PCM.
(See PCM INSPECTION [L3] ).
(See PCM INSPECTION [AJ] ).
Inspect ABS/TCS HU/CM.
(See ABS/TCS HU/CM INSPECTION ).		 -
TCM_MSG
(Missing message from the TCM)		 Present/Not Present
  • Present: Circuit in the TCM is normal.
  • Not Present: Circuit in the TCM is abnormal.
 Inspect TCM.
(See TCM INSPECTION [FS5A-EL] )
(See TCM INSPECTION [AW6A-EL] )
Inspect ABS/TCS HU/CM.
(See ABS/TCS HU/CM INSPECTION )		 -
scientia non olet · About Mike's Workshop Manuals