Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Mazda >> 2006 >> MX-5 Miata Base >> Repair and Diagnosis (Single Page) >> Brakes >> Traction Control >> On-Board Diagnostic [Abs) >> DTC Table >> PID/DATA Monitor Table

PID/DATA Monitor Table

PID/DATA MONITOR TABLE

PID name (definition) Unit/Condition Operation condition (reference) Action ABS HU/CM terminal
ABS_VOLT
(System battery voltage value)
V
  • Ignition switch at ON:
  • Approx. 12.2 V 
  • Idling: Approx. 14.1 V 
Inspect the power supply circuit.
(See ABS SYSTEM INSPECTION .)
J
ABSLF_I
(Left front inlet solenoid valve output state)
On/Off
  • Solenoid valve activated: On
  • Solenoid valve not activated: Off
Inspect the ABS HU/CM.
(See ABS HU/CM INSPECTION .)
-
ABSLF_O
(Left front outlet solenoid valve output state)
On/Off
  • Solenoid valve activated: On
  • Solenoid valve not activated: Off
Inspect the ABS HU/CM.
(See ABS HU/CM INSPECTION .)
-
ABSLR_I
(Left rear inlet solenoid valve output state)
On/Off
  • Solenoid valve activated: On
  • Solenoid valve not activated: Off
Inspect the ABS HU/CM.
(See ABS HU/CM INSPECTION .)
-
ABSLR_O
(Left rear outlet solenoid valve output state)
On/Off
  • Solenoid valve activated: On
  • Solenoid valve not activated: Off
Inspect the ABS HU/CM.
(See ABS HU/CM INSPECTION .)
-
ABSPMPRLY
(Motor relay output state)
On/Off
  • Relay activated: On
  • Relay not activated: Off
Inspect the ABS HU/CM.
(See ABS HU/CM INSPECTION .)
-
ABSRF_I
(Right front inlet solenoid valve output state)
On/Off
  • Solenoid valve activated: On
  • Solenoid valve not activated: Off
Inspect the ABS HU/CM.
(See ABS HU/CM INSPECTION .)
-
ABSRF_O
(Right front outlet solenoid valve output state)
On/Off
  • Solenoid valve activated: On
  • Solenoid valve not activated: Off
Inspect the ABS HU/CM.
(See ABS HU/CM INSPECTION .)
-
ABSRR_I
(Right rear inlet solenoid valve output state)
On/Off
  • Solenoid valve activated: On
  • Solenoid valve not activated: Off
Inspect the ABS HU/CM.
(See ABS HU/CM INSPECTION .)
-
ABSRR_O
(Right rear outlet solenoid valve output state)
On/Off
  • Solenoid valve activated: On
  • Solenoid valve not activated: Off
Inspect the ABS HU/CM.
(See ABS HU/CM INSPECTION .)
-
ABSVLVRLY
(Fail-safe relay output state)
On/Off
  • Fail-safe relay is activated: On
  • Fail-safe relay is deactivated: Off
Inspect ABS HU/CM.
(See ABS HU/CM INSPECTION )
-
BOO_ABS
(Brake pedal switch input)
On/Off
  • Brake pedal depressed: On
  • Brake pedal released: Off
Inspect the brake switch. N
CCNTABS
(Number of continuous codes)
-
  • DTCs detected: 1-255 
  • No DTCs detected:
Perform the DTC inspection. -
LF_WSPD
(Left front ABS wheel-speed sensor input)
KPH, MPH
  • Vehicle stopped: 0 KPH, 0 MPH 
  • Vehicle running: Vehicle speed
Inspect the ABS wheel-speed sensor. E, F
LR_WSPD
(Left rear ABS wheel-speed sensor input)
KPH, MPH
  • Vehicle stopped: 0 KPH, 0 MPH 
  • Vehicle running: Vehicle speed
Inspect the ABS wheel-speed sensor. G, H
PMP_MOTOR
(Pump motor output state)
On/Off
  • Pump motor activated: On
  • Pump motor not activated: Off
Inspect the ABS HU/CM.
(See ABS HU/CM INSPECTION .)
-
RF_WSPD
(Right front ABS wheel-speed sensor input)
KPH, MPH
  • Vehicle stopped: 0 KPH, 0 MPH 
  • Vehicle running: Vehicle speed
Inspect the ABS wheel-speed sensor. M, O
RR_WSPD
(Right rear ABS wheel-speed sensor input)
KPH, MPH
  • Vehicle stopped: 0 KPH, 0 MPH 
  • Vehicle running: Vehicle speed
Inspect the ABS wheel-speed sensor. I, L
ACTIVE COMMAND MODES TABLE

Command name Output part Operation Operating condition
LF_INLET LF inlet solenoid valve On/Off Ignition switch at ON
LF_OUTLET LF outlet solenoid valve
LR_INLET LR inlet solenoid valve
LR_OUTLET LR outlet solenoid valve
PMP_MOTOR Pump motor
RF_INLET RF inlet solenoid valve
RF_OUTLET RF outlet solenoid valve
RR_INLET RR inlet solenoid valve
RR_OUTLET RR outlet solenoid valve