| DDM |
B1C03:23 |
Memory #1 Switch: Signal Stuck Low |
GO to Pinpoint Test G |
| DDM |
B1C04:23 |
Memory #2 Switch: Signal Stuck Low |
GO to Pinpoint Test G |
| DDM |
B1C05:23 |
Memory #3 Switch: Signal Stuck Low |
GO to Pinpoint Test G |
| DSM |
B1067:24 |
Lumbar In Switch: Signal Stuck High |
GO to Pinpoint Test Z |
| DSM |
B1068:24 |
Lumbar Out Switch: Signal Stuck High |
GO to Pinpoint Test Z |
| DSM |
B1088:83 |
LIN Bus 'B': Value Of Signal Protection Calculation Incorrect |
GO to Pinpoint Test Y |
| DSM |
B1088:87 |
LIN Bus 'B': Missing Message |
GO to Pinpoint Test Y |
| DSM |
B1153:4B |
Driver Seat Cushion: Over Temperature |
GO to Pinpoint Test K |
| DSM |
B115B:11 |
Front Driver Seat Heater: Circuit Short To Ground |
GO to Pinpoint Test K |
| DSM |
B115B:12 |
Front Driver Seat Heater: Circuit Short To Battery |
GO to Pinpoint Test K |
| DSM |
B115B:13 |
Front Driver Seat Heater: Circuit Open |
GO to Pinpoint Test K |
| DSM |
B1208:11 |
Driver Seat Cushion Temperature Sensor: Circuit Short To Ground |
GO to Pinpoint Test K |
| DSM |
B1208:15 |
Driver Seat Cushion Temperature Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test K |
| DSM |
B1208:2A |
Driver Seat Cushion Temperature Sensor: Signal Stuck In Range |
GO to Pinpoint Test K |
| DSM |
B14BD:11 |
Driver Seat Cushion Blower: Circuit Short To Ground |
GO to Pinpoint Test M |
| DSM |
B14BD:13 |
Driver Seat Cushion Blower: Circuit Open |
GO to Pinpoint Test M |
| DSM |
B14C3:24 |
Seat Height Rear Down Switch: Signal Stuck High |
GO to Pinpoint Test Z |
| DSM |
B14C4:24 |
Seat Height Rear Up Switch: Signal Stuck High |
GO to Pinpoint Test Z |
| DSM |
B14CE:11 |
Seat Horizontal Motor Output: Circuit Short To Ground |
GO to Pinpoint Test F |
| DSM |
B14CE:12 |
Seat Horizontal Motor Output: Circuit Short To Battery |
GO to Pinpoint Test F |
| DSM |
B14CE:13 |
Seat Horizontal Motor Output: Circuit Open |
GO to Pinpoint Test F |
| DSM |
B14CF:11 |
Seat Recline Motor Output: Circuit Short To Ground |
GO to Pinpoint Test F |
| DSM |
B14CF:12 |
Seat Recline Motor Output: Circuit Short To Battery |
GO to Pinpoint Test F |
| DSM |
B14CF:13 |
Seat Recline Motor Output: Circuit Open |
GO to Pinpoint Test F |
| DSM |
B14D0:11 |
Seat Height Front/Tilt Motor Output: Circuit Short To Ground |
GO to Pinpoint Test F |
| DSM |
B14D0:12 |
Seat Height Front/Tilt Motor Output: Circuit Short To Battery |
GO to Pinpoint Test F |
| DSM |
B14D0:13 |
Seat Height Front/Tilt Motor Output: Circuit Open |
GO to Pinpoint Test F |
| DSM |
B14D2:11 |
Seat Height Rear Motor Output: Circuit Short To Ground |
GO to Pinpoint Test F |
| DSM |
B14D2:12 |
Seat Height Rear Motor Output: Circuit Short To Battery |
GO to Pinpoint Test F |
| DSM |
B14D2:13 |
Seat Height Rear Motor Output: Circuit Open |
GO to Pinpoint Test F |
| DSM |
B151F:11 |
Left Cushion Motor Output: Circuit Short To Ground |
GO to Pinpoint Test D |
| DSM |
B151F:12 |
Left Cushion Motor Output: Circuit Short To Battery |
GO to Pinpoint Test D |
| DSM |
B151F:13 |
Left Cushion Motor Output: Circuit Open |
GO to Pinpoint Test D |
| DSM |
B1520:11 |
Right Cushion Motor Output: Circuit Short To Ground |
GO to Pinpoint Test D |
| DSM |
B1520:12 |
Right Cushion Motor Output: Circuit Short To Battery |
GO to Pinpoint Test D |
| DSM |
B1520:13 |
Right Cushion Motor Output: Circuit Open |
GO to Pinpoint Test D |
| DSM |
B1522:11 |
Lumbar Motor Output: Circuit Short To Ground |
GO to Pinpoint Test B |
| DSM |
B1522:12 |
Lumbar Motor Output: Circuit Short To Battery |
GO to Pinpoint Test B |
| DSM |
B1522:13 |
Lumbar Motor Output: Circuit Open |
GO to Pinpoint Test B |
| DSM |
B1527:24 |
Left Cushion Fore Switch: Signal Stuck High |
GO to Pinpoint Test Z |
| DSM |
B1528:24 |
Left Cushion Aft Switch: Signal Stuck High |
GO to Pinpoint Test Z |
| DSM |
B1529:24 |
Right Cushion Fore Switch: Signal Stuck High |
GO to Pinpoint Test Z |
| DSM |
B152A:24 |
Right Cushion Aft Switch: Signal Stuck High |
GO to Pinpoint Test Z |
| DSM |
B1562:11 |
Driver Seat Back Blower Speed: Circuit Short To Ground |
GO to Pinpoint Test M |
| DSM |
B1562:12 |
Driver Seat Back Blower Speed: Circuit Short To Battery |
GO to Pinpoint Test M |
| DSM |
B1564:11 |
Driver Seat Cushion Blower Speed: Circuit Short To Ground |
GO to Pinpoint Test M |
| DSM |
B1564:12 |
Driver Seat Cushion Blower Speed: Circuit Short To Battery |
GO to Pinpoint Test M |
| DSM |
B171F:11 |
Seat Horizontal Position Sensor: Circuit Short To Ground |
GO to Pinpoint Test G |
| DSM |
B171F:15 |
Seat Horizontal Position Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test G |
| DSM |
B1B96:24 |
Seat Slide Forward Switch: Signal Stuck High |
GO to Pinpoint Test Z |
| DSM |
B1B97:24 |
Seat Slide Backward Switch: Signal Stuck High |
GO to Pinpoint Test Z |
| DSM |
B1B98:24 |
Seat Tilt Up Switch: Signal Stuck High |
GO to Pinpoint Test Z |
| DSM |
B1B99:24 |
Seat Tilt Down Switch: Signal Stuck High |
GO to Pinpoint Test Z |
| DSM |
B1C00:24 |
Seat Recline Up Switch: Signal Stuck High |
GO to Pinpoint Test Z |
| DSM |
B1C01:24 |
Seat Recline Down Switch: Signal Stuck High |
GO to Pinpoint Test Z |
| DSM |
U0100:00 |
Lost Communication With ECM/PCM 'A': No Sub Type Information |
GO to Pinpoint Test Q |
| DSM |
U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test R |
| DSM |
U0199:00 |
Lost Communication With 'Door Control Module A': No Sub Type Information |
GO to Pinpoint Test AN |
| DSM |
U0212:00 |
Lost Communication With Steering Column Control Module: No Sub Type Information |
GO to Pinpoint Test S |
| DSM |
U0253:00 |
Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test T |
| DSM |
U0257:00 |
Lost Communication With Front Controls / Display Interface Module: No Sub Type Information |
GO to Pinpoint Test AB |
| DSM |
U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test AP |
| DSM |
U1000:00 |
Solid State Driver Protection Active -Driver Disabled: No Sub Type Information |
GO to Pinpoint Test AD |
| DSM |
U2013:24 |
Switch Pack: Signal Stuck High |
GO to Pinpoint Test Z |
| DSM |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test U |
| DSM |
U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test AQ |
| DSM |
U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test V |
| DSM |
U3500:17 |
Control Module Input Power 'A' Circuit Range/Performance: Circuit Voltage Above Threshold |
GO to Pinpoint Test X |
| SCMB |
B1067:24 |
Lumbar In Switch: Signal Stuck High |
GO to Pinpoint Test AA |
| SCMB |
B1068:24 |
Lumbar Out Switch: Signal Stuck High |
GO to Pinpoint Test AA |
| SCMB |
B1151:4B |
Passenger Seat Cushion: Over Temperature |
GO to Pinpoint Test L |
| SCMB |
B115A:11 |
Front Passenger Seat Heater: Circuit Short To Ground |
GO to Pinpoint Test L |
| SCMB |
B115A:12 |
Front Passenger Seat Heater: Circuit Short To Battery |
GO to Pinpoint Test L |
| SCMB |
B115A:13 |
Front Passenger Seat Heater: Circuit Open |
GO to Pinpoint Test L |
| SCMB |
B120A:11 |
Passenger Seat Cushion Temperature Sensor: Circuit Short To Ground |
GO to Pinpoint Test L |
| SCMB |
B120A:15 |
Passenger Seat Cushion Temperature Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test L |
| SCMB |
B120A:2A |
Passenger Seat Cushion Temperature Sensor: Signal Stuck In Range |
GO to Pinpoint Test L |
| SCMB |
B14C0:11 |
Passenger Seat Cushion Blower: Circuit Short To Ground |
GO to Pinpoint Test N |
| SCMB |
B14C0:13 |
Passenger Seat Cushion Blower: Circuit Open |
GO to Pinpoint Test N |
| SCMB |
B14C3:24 |
Seat Height Rear Down Switch: Signal Stuck High |
GO to Pinpoint Test AA |
| SCMB |
B14C4:24 |
Seat Height Rear Up Switch: Signal Stuck High |
GO to Pinpoint Test AA |
| SCMB |
B14CE:11 |
Seat Horizontal Motor Output: Circuit Short To Ground |
GO to Pinpoint Test A |
| SCMB |
B14CE:12 |
Seat Horizontal Motor Output: Circuit Short To Battery |
GO to Pinpoint Test A |
| SCMB |
B14CE:13 |
Seat Horizontal Motor Output: Circuit Open |
GO to Pinpoint Test A |
| SCMB |
B14CF:11 |
Seat Recline Motor Output: Circuit Short To Ground |
GO to Pinpoint Test A |
| SCMB |
B14CF:12 |
Seat Recline Motor Output: Circuit Short To Battery |
GO to Pinpoint Test A |
| SCMB |
B14CF:13 |
Seat Recline Motor Output: Circuit Open |
GO to Pinpoint Test A |
| SCMB |
B14D0:11 |
Seat Height Front/Tilt Motor Output: Circuit Short To Ground |
GO to Pinpoint Test A |
| SCMB |
B14D0:12 |
Seat Height Front/Tilt Motor Output: Circuit Short To Battery |
GO to Pinpoint Test A |
| SCMB |
B14D0:13 |
Seat Height Front/Tilt Motor Output: Circuit Open |
GO to Pinpoint Test A |
| SCMB |
B14D2:11 |
Seat Height Rear Motor Output: Circuit Short To Ground |
GO to Pinpoint Test A |
| SCMB |
B14D2:12 |
Seat Height Rear Motor Output: Circuit Short To Battery |
GO to Pinpoint Test A |
| SCMB |
B14D2:13 |
Seat Height Rear Motor Output: Circuit Open |
GO to Pinpoint Test A |
| SCMB |
B151F:11 |
Left Cushion Motor Output: Circuit Short To Ground |
GO to Pinpoint Test E |
| SCMB |
B151F:12 |
Left Cushion Motor Output: Circuit Short To Battery |
GO to Pinpoint Test E |
| SCMB |
B151F:13 |
Left Cushion Motor Output: Circuit Open |
GO to Pinpoint Test E |
| SCMB |
B1520:11 |
Right Cushion Motor Output: Circuit Short To Ground |
GO to Pinpoint Test E |
| SCMB |
B1520:12 |
Right Cushion Motor Output: Circuit Short To Battery |
GO to Pinpoint Test E |
| SCMB |
B1520:13 |
Right Cushion Motor Output: Circuit Open |
GO to Pinpoint Test E |
| SCMB |
B1522:11 |
Lumbar Motor Output: Circuit Short To Ground |
GO to Pinpoint Test C |
| SCMB |
B1522:12 |
Lumbar Motor Output: Circuit Short To Battery |
GO to Pinpoint Test C |
| SCMB |
B1522:13 |
Lumbar Motor Output: Circuit Open |
GO to Pinpoint Test C |
| SCMB |
B1527:24 |
Left Cushion Fore Switch: Signal Stuck High |
GO to Pinpoint Test AA |
| SCMB |
B1528:24 |
Left Cushion Aft Switch: Signal Stuck High |
GO to Pinpoint Test AA |
| SCMB |
B1529:24 |
Right Cushion Fore Switch: Signal Stuck High |
GO to Pinpoint Test AA |
| SCMB |
B152A:24 |
Right Cushion Aft Switch: Signal Stuck High |
GO to Pinpoint Test AA |
| SCMB |
B1563:11 |
Passenger Seat Back Blower Speed: Circuit Short To Ground |
GO to Pinpoint Test N |
| SCMB |
B1563:12 |
Passenger Seat Back Blower Speed: Circuit Short To Battery |
GO to Pinpoint Test N |
| SCMB |
B1565:11 |
Passenger Seat Cushion Blower Speed: Circuit Short To Ground |
GO to Pinpoint Test N |
| SCMB |
B1565:12 |
Passenger Seat Cushion Blower Speed: Circuit Short To Battery |
GO to Pinpoint Test N |
| SCMB |
B171F:11 |
Seat Horizontal Position Sensor: Circuit Short To Ground |
GO to Pinpoint Test A |
| SCMB |
B171F:15 |
Seat Horizontal Position Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test A |
| SCMB |
B1B96:24 |
Seat Slide Forward Switch: Signal Stuck High |
GO to Pinpoint Test AA |
| SCMB |
B1B97:24 |
Seat Slide Backward Switch: Signal Stuck High |
GO to Pinpoint Test AA |
| SCMB |
B1B98:24 |
Seat Tilt Up Switch: Signal Stuck High |
GO to Pinpoint Test AA |
| SCMB |
B1B99:24 |
Seat Tilt Down Switch: Signal Stuck High |
GO to Pinpoint Test AA |
| SCMB |
B1C00:24 |
Seat Recline Up Switch: Signal Stuck High |
GO to Pinpoint Test AA |
| SCMB |
B1C01:24 |
Seat Recline Down Switch: Signal Stuck High |
GO to Pinpoint Test AA |
| SCMB |
U0100:00 |
Lost Communication With ECM/PCM 'A': No Sub Type Information |
GO to Pinpoint Test Q |
| SCMB |
U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test R |
| SCMB |
U0199:00 |
Lost Communication With 'Door Control Module A': No Sub Type Information |
GO to Pinpoint Test AO |
| SCMB |
U0253:00 |
Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test T |
| SCMB |
U0257:00 |
Lost Communication With Front Controls / Display Interface Module: No Sub Type Information |
GO to Pinpoint Test AC |
| SCMB |
U1000:00 |
Solid State Driver Protection Active -Driver Disabled: No Sub Type Information |
GO to Pinpoint Test AE |
| SCMB |
U2013:24 |
Switch Pack: Signal Stuck High |
GO to Pinpoint Test AA |
| SCMB |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test U |
| SCMB |
U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test V |
| SCMB |
U3000:4A |
Control Module: Incorrect Component Installed |
GO to Pinpoint Test W |
| SCMB |
U3500:17 |
Control Module Input Power 'A' Circuit Range/Performance: Circuit Voltage Above Threshold |
GO to Pinpoint Test X |
| SCMG |
B146F:00 |
Back Bladder System Electropneumatic Failure: No Sub Type Information |
GO to Pinpoint Test O |
| SCMG |
B146F:04 |
Back Bladder System Electropneumatic Failure: System Internal Failure |
GO to Pinpoint Test O |
| SCMG |
B146F:87 |
Back Bladder System Electropneumatic Failure: Missing Message |
GO to Pinpoint Test O |
| SCMG |
B1470:00 |
Cushion Bladder System Electropneumatic Failure: No Sub Type Information |
GO to Pinpoint Test O |
| SCMG |
B1470:04 |
Cushion Bladder System Electropneumatic Failure: System Internal Failure |
GO to Pinpoint Test O |
| SCMG |
B1470:87 |
Cushion Bladder System Electropneumatic Failure: Missing Message |
GO to Pinpoint Test O |
| SCMG |
B1471:11 |
Multi-Contour Seat Switch Input: Circuit Short To Ground |
GO to Pinpoint Test O |
| SCMG |
B1471:13 |
Multi-Contour Seat Switch Input: Circuit Open |
GO to Pinpoint Test O |
| SCMG |
B1471:2A |
Multi-Contour Seat Switch Input: Signal Stuck In Range |
GO to Pinpoint Test O |
| SCMG |
B1473:11 |
Pump Driver: Circuit Short To Ground |
GO to Pinpoint Test O |
| SCMG |
U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test AF |
| SCMG |
U0208:00 |
Lost Communication With Seat Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AG |
| SCMG |
U0253:00 |
Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test AI |
| SCMG |
U0256:00 |
Lost Communication With Front Controls Interface Module 'A': No Sub Type Information |
GO to Pinpoint Test AJ |
| SCMG |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AL |
| SCMG |
U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AM |
| SCMH |
B146F:00 |
Back Bladder System Electropneumatic Failure: No Sub Type Information |
GO to Pinpoint Test P |
| SCMH |
B146F:04 |
Back Bladder System Electropneumatic Failure: System Internal Failure |
GO to Pinpoint Test P |
| SCMH |
B146F:87 |
Back Bladder System Electropneumatic Failure: Missing Message |
GO to Pinpoint Test P |
| SCMH |
B1470:00 |
Cushion Bladder System Electropneumatic Failure: No Sub Type Information |
GO to Pinpoint Test P |
| SCMH |
B1470:04 |
Cushion Bladder System Electropneumatic Failure: System Internal Failure |
GO to Pinpoint Test P |
| SCMH |
B1470:87 |
Cushion Bladder System Electropneumatic Failure: Missing Message |
GO to Pinpoint Test P |
| SCMH |
B1471:11 |
Multi-Contour Seat Switch Input: Circuit Short To Ground |
GO to Pinpoint Test P |
| SCMH |
B1471:13 |
Multi-Contour Seat Switch Input: Circuit Open |
GO to Pinpoint Test P |
| SCMH |
B1471:2A |
Multi-Contour Seat Switch Input: Signal Stuck In Range |
GO to Pinpoint Test P |
| SCMH |
B1473:11 |
Pump Driver: Circuit Short To Ground |
GO to Pinpoint Test P |
| SCMH |
U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test AF |
| SCMH |
U0208:00 |
Lost Communication With Seat Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AG |
| SCMH |
U024B:00 |
Lost Communication with Seat Control Module 'G': No Sub Type Information |
GO to Pinpoint Test AH |
| SCMH |
U0253:00 |
Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test AI |
| SCMH |
U0256:00 |
Lost Communication With Front Controls Interface Module 'A': No Sub Type Information |
GO to Pinpoint Test AJ |
| SCMH |
U0455:82 |
Invalid Data Received From Restraints Occupant Classification System Module 'A': Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test AK |
| SCMH |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AL |
| SCMH |
U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AM |