| ABS |
C0051:23 |
Steering Wheel Position Sensor: Signal Stuck Low |
GO to Pinpoint Test S |
| ABS |
C0051:27 |
Steering Wheel Position Sensor: Signal Rate Of Change Above Threshold |
GO to Pinpoint Test S |
| ABS |
C0051:28 |
Steering Wheel Position Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test S |
| ABS |
C0051:29 |
Steering Wheel Position Sensor: Signal Invalid |
GO to Pinpoint Test S |
| ABS |
C0051:54 |
Steering Wheel Position Sensor: Missing Calibration |
GO to Pinpoint Test S |
| ABS |
C0051:62 |
Steering Wheel Position Sensor: Signal Compare Failure |
GO to Pinpoint Test S |
| ABS |
C0051:64 |
Steering Wheel Position Sensor: Signal Plausibility Failure |
GO to Pinpoint Test S |
| ABS |
C0051:67 |
Steering Wheel Position Sensor: Signal Incorrect After Event |
GO to Pinpoint Test S |
| ABS |
C0051:82 |
Steering Wheel Position Sensor: Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test S |
| ABS |
C0051:85 |
Steering Wheel Position Sensor: Signal Above Allowable Range |
GO to Pinpoint Test S |
| ABS |
C0051:86 |
Steering Wheel Position Sensor: Signal Invalid |
GO to Pinpoint Test S |
| ABS |
C0051:96 |
Steering Wheel Position Sensor: Component Internal Failure |
GO to Pinpoint Test S |
| ABS |
C006B:00 |
Stability System Active Too Long: No Sub Type Information |
GO to Pinpoint Test S |
| PSCM |
B1D23:4B |
Overheat Sensor: Over Temperature |
GO to Pinpoint Test AP |
| PSCM |
C1110:56 |
Power steering Calibration Data: Invalid/Incompatible Configuration |
GO to Pinpoint Test O |
| PSCM |
C1B00:49 |
Steering Angle Sensor: Internal Electronic Failure |
GO to Pinpoint Test AS |
| PSCM |
C1B00:62 |
Steering Angle Sensor: Signal Compare Failure |
GO to Pinpoint Test AS |
| PSCM |
C200B:49 |
Steering Shaft Torque Sensor 1: Internal Electronic Failure |
GO to Pinpoint Test AT |
| PSCM |
C200B:62 |
Steering Shaft Torque Sensor 1: Signal Compare Failure |
GO to Pinpoint Test AT |
| PSCM |
C200D:49 |
Motor Rotation Angle Sensor: Internal Electronic Failure |
GO to Pinpoint Test AU |
| PSCM |
C200D:62 |
Motor Rotation Angle Sensor: Signal Compare Failure |
GO to Pinpoint Test AU |
| PSCM |
U0001:88 |
High Speed CAN Communication Bus: Bus Off |
GO to Pinpoint Test U |
| PSCM |
U0100:00 |
Lost Communication With ECM/PCM 'A': No Sub Type Information |
GO to Pinpoint Test V |
| PSCM |
U011D:00 |
Lost Communication With All Wheel Drive Control Module: No Sub Type Information |
GO to Pinpoint Test W |
| PSCM |
U0121:00 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information |
GO to Pinpoint Test X |
| PSCM |
U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test Y |
| PSCM |
U0146:00 |
Lost Communication With Serial Data Gateway 'A': No Sub Type Information |
GO to Pinpoint Test Z |
| PSCM |
U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AA |
| PSCM |
U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test AB |
| PSCM |
U0159:00 |
Lost Communication With Parking Assist Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AC |
| PSCM |
U023A:00 |
Lost Communication With Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test AD |
| PSCM |
U023B:00 |
Lost Communication With Image Processing Module B: No Sub Type Information |
GO to Pinpoint Test AN |
| PSCM |
U0253:00 |
Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test AE |
| PSCM |
U0256:00 |
Lost Communication With Front Controls Interface Module 'A': No Sub Type Information |
GO to Pinpoint Test AF |
| PSCM |
U0401:00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
GO to Pinpoint Test AG |
| PSCM |
U0415:00 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AH |
| PSCM |
U0415:22 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': Signal Amplitude Greater Than Maximum |
GO to Pinpoint Test AH |
| PSCM |
U041E:00 |
Invalid Data Received From All Wheel Drive Control Module: No Sub Type Information |
GO to Pinpoint Test W |
| PSCM |
U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test Y |
| PSCM |
U0423:00 |
Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information |
GO to Pinpoint Test AB |
| PSCM |
U0447:00 |
Invalid Data Received From Serial Data Gateway Module 'A': No Sub Type Information |
GO to Pinpoint Test AI |
| PSCM |
U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AK |
| PSCM |
U045A:00 |
Invalid Data Received From Parking Assist Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AJ |
| PSCM |
U053B:00 |
Invalid Data Received From Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test AD |
| PSCM |
U053C:00 |
Invalid Data Received From Image Processing Module B: No Sub Type Information |
GO to Pinpoint Test AN |
| PSCM |
U0554:00 |
Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test AL |
| PSCM |
U0557:00 |
Invalid Data Received From Front Controls Interface Module 'A': No Sub Type Information |
GO to Pinpoint Test AM |
| PSCM |
U2014:78 |
Control Module Hardware: Alignment Or Adjustment Incorrect |
GO to Pinpoint Test AW |
| PSCM |
U2014:81 |
Control Module Hardware: Invalid Serial Data Received |
GO to Pinpoint Test AW |
| PSCM |
U2014:92 |
Control Module Hardware: Performance Or Incorrect Operation |
GO to Pinpoint Test AW |
| PSCM |
U2016:09 |
Control Module Main Software: Component Failure |
GO to Pinpoint Test AX |
| PSCM |
U2016:47 |
Control Module Main Software: Watchdog/Safety μC Failure |
GO to Pinpoint Test AX |
| PSCM |
U2016:48 |
Control Module Main Software: Supervision Software Failure |
GO to Pinpoint Test AX |
| PSCM |
U2016:57 |
Control Module Main Software: Invalid/Incompatible Software Component |
GO to Pinpoint Test AX |
| PSCM |
U2016:66 |
Control Module Main Software: Signal Has Too Many Transitions/Events |
GO to Pinpoint Test AX |
| PSCM |
U2016:94 |
Control Module Main Software: Unexpected Operation |
GO to Pinpoint Test AX |
| PSCM |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AY |
| PSCM |
U2300:29 |
Central Configuration: Signal Invalid |
GO to Pinpoint Test AZ |
| PSCM |
U2300:55 |
Central Configuration: Not Configured |
GO to Pinpoint Test BA |
| PSCM |
U2300:56 |
Central Configuration: Invalid/Incompatible Configuration |
GO to Pinpoint Test BA |
| PSCM |
U3000:05 |
Control Module: System Programming Failure |
GO to Pinpoint Test B |
| PSCM |
U3000:05 |
Control Module: System Programming Failure |
GO to Pinpoint Test B |
| PSCM |
U3000:42 |
Control Module: General Memory Failure |
GO to Pinpoint Test B |
| PSCM |
U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test B |
| PSCM |
U3000:4B |
Control Module: Over Temperature |
GO to Pinpoint Test B |
| PSCM |
U3000:61 |
Control Module: Signal Calculation Failure |
GO to Pinpoint Test B |
| PSCM |
U3000:66 |
Control Module: Signal Has Too Many Transitions/Events |
GO to Pinpoint Test B |
| PSCM |
U3001:68 |
Control Module Improper Shutdown Performance: Event Information |
GO to Pinpoint Test AR |
| PSCM |
U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test AQ |
| PSCM |
U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test AQ |
| PSCM |
U3003:68 |
Battery Voltage: Event Information |
GO to Pinpoint Test AQ |
| PSCM |
U3008:1B |
Control Module Ground 'A': Circuit Resistance Above Threshold |
GO to Pinpoint Test BB |
| PSCM |
U3009:1B |
Control Module Ground 'B': Circuit Resistance Above Threshold |
GO to Pinpoint Test BB |