| BCM |
B155E:00 |
Incorrect Response from Immobilizer SubControl Module: No Sub Type Information |
GO to Pinpoint Test I |
| BCM |
B155F:51 |
Phone As A Key: Not Programmed |
GO to Pinpoint Test E |
| PCM |
P1594:00 |
Forced Engine Shutdown - Remote Start System Fault, No Unattended Vehicle Timeout: No Sub Type Information |
GO to Pinpoint Test K |
| PCM |
P1595:00 |
Forced Engine Shutdown - Remote Start System Fault, Transmission Range Not In Park Position: No Sub Type Information |
GO to Pinpoint Test K |
| RFA |
B1589:29 |
Antenna #3: Signal Invalid |
GO to Pinpoint Test B |
| RFA |
B1589:57 |
Antenna #3: Invalid/Incompatible Software Component |
GO to Pinpoint Test B |
| RFA |
B1590:29 |
Antenna #4: Signal Invalid |
GO to Pinpoint Test C |
| RFA |
B1590:57 |
Antenna #4: Invalid/Incompatible Software Component |
GO to Pinpoint Test C |
| RFA |
B1591:29 |
Antenna #5: Signal Invalid |
GO to Pinpoint Test A |
| RFA |
B1591:57 |
Antenna #5: Invalid/Incompatible Software Component |
GO to Pinpoint Test A |
| RFA |
B1592:29 |
Antenna #6: Signal Invalid |
GO to Pinpoint Test B |
| RFA |
B1592:57 |
Antenna #6: Invalid/Incompatible Software Component |
GO to Pinpoint Test B |
| RFA |
B1593:29 |
Antenna #7: Signal Invalid |
GO to Pinpoint Test C |
| RFA |
B1593:57 |
Antenna #7: Invalid/Incompatible Software Component |
GO to Pinpoint Test C |
| RFA |
B1594:29 |
Antenna #8: Signal Invalid |
GO to Pinpoint Test B |
| RFA |
B1594:57 |
Antenna #8: Invalid/Incompatible Software Component |
GO to Pinpoint Test B |
| RFA |
B1595:29 |
Antenna #9: Signal Invalid |
GO to Pinpoint Test A |
| RFA |
B1595:57 |
Antenna #9: Invalid/Incompatible Software Component |
GO to Pinpoint Test A |
| RFA |
B1596:29 |
Antenna #10: Signal Invalid |
GO to Pinpoint Test B |
| RFA |
B1596:57 |
Antenna #10: Invalid/Incompatible Software Component |
GO to Pinpoint Test B |
| RFA |
B1A56:29 |
Antenna: Signal Invalid |
GO to Pinpoint Test C |
| RFA |
B1A56:57 |
Antenna: Invalid/Incompatible Software Component |
GO to Pinpoint Test C |
| RFA |
B1D55:29 |
Antenna #2: Signal Invalid |
GO to Pinpoint Test A |
| RFA |
B1D55:57 |
Antenna #2: Invalid/Incompatible Software Component |
GO to Pinpoint Test A |
| RFA |
P1269:00 |
Immobilizer Code Not Programmed: No Sub Type Information |
GO to Pinpoint Test E |
| RFA |
P1602:00 |
Immobilizer/ECM Communication Error: No Sub Type Information |
GO to Pinpoint Test E |
| RFA |
P1622:00 |
Immobilizer ID Does Not Match: No Sub Type Information |
GO to Pinpoint Test E |
| RFA |
P1623:00 |
Immobilizer Code Word/ID Number Write Failure: No Sub Type Information |
GO to Pinpoint Test E |
| RFA |
U0146:00 |
Lost Communication With Serial Data Gateway 'A': No Sub Type Information |
GO to Pinpoint Test H |
| RFA |
U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test E |
| RFA |
U200D:11 |
Control Module Output Power A: Circuit Short To Ground |
GO to Pinpoint Test A |
| RFA |
U200D:15 |
Control Module Output Power A: Circuit Short To Battery Or Open |
GO to Pinpoint Test A |
| RFA |
U200E:11 |
Control Module Output Power B: Circuit Short To Ground |
GO to Pinpoint Test B |
| RFA |
U200E:15 |
Control Module Output Power B: Circuit Short To Battery Or Open |
GO to Pinpoint Test B |
| RFA |
U200F:11 |
Control Module Output Power C: Circuit Short To Ground |
GO to Pinpoint Test C |
| RFA |
U200F:15 |
Control Module Output Power C: Circuit Short To Battery Or Open |
GO to Pinpoint Test C |
| RFA |
U201A:55 |
Control Module Main Calibration Data: Not Configured |
GO to Pinpoint Test D |
| RFA |
U2100:55 |
Initial Configuration Not Complete: Not Configured |
GO to Pinpoint Test D |
| RFA |
U211A:46 |
Trusted Real-Time Operational Network (TRON) Configuration: Calibration/Parameter Memory Failure |
GO to Pinpoint Test H |
| RFA |
U211B:05 |
Control Module Message Authentication: System Programming Failure |
GO to Pinpoint Test G |
| RFA |
U211B:08 |
Control Module Message Authentication: Bus Signal / Message Failure |
GO to Pinpoint Test G |
| RFA |
U211B:43 |
Control Module Message Authentication: Special Memory Failure |
GO to Pinpoint Test G |
| RFA |
U211B:51 |
Control Module Message Authentication: Not Programmed |
GO to Pinpoint Test D |
| RFA |
U211B:81 |
Control Module Message Authentication: Invalid Serial Data Received |
GO to Pinpoint Test G |
| RFA |
U211B:87 |
Control Module Message Authentication: Missing Message |
GO to Pinpoint Test G |
| RFA |
U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test G |