Pinpoint Test BJ: Abs (Anti-Lock Brake System) Module Communication Concern With SCCM (Steering Column Control Module)
- Refer to Module Communications Network
for schematic and connector information.
Normal Operation and Fault Conditions
With the ignition ON, the SCCM sends messages to the ABS module over the HS-CAN2. If the ABS module does not receive these messages within the specified time frame, the ABS module sets Diagnostic Trouble Codes (DTCs). This can be due to a SCCM failure, a circuit failure on the CAN or an excessive load on the network. For information on the messages sent to the ABS module by the SCCM, REFER to: Anti-Lock Brake System (ABS) and Stability Control - System Operation and Component Description .
DTC Fault Trigger Conditions
DTC Description Fault Trigger Condition ABS U0212:86 Lost Communication With Steering Column Control Module: Signal Invalid If the ABS module recieves the front wiper status messages from the SCCM with an invalid value for more than the allotted time, this DTC is set. ABS U0212:87 Lost Communication With Steering Column Control Module: Missing Message If the ABS module does not receive the steering angle messages from the SCCM within a pre-determined time frame, this DTC is set. Possible Causes
- Network communication concern
- SCCM
- BJ1 CHECK THE COMMUNICATION NETWORK
- Ignition ON.
- Press Read Vehicle Information button to retrieve DTCs from the vehicle. NOTE: DTCs may be displayed from previous diagnostic actions.
Does the SCCM pass the Network Test?
Yes RETRIEVE and RECORD all SCCM DTCs. REFER to appropriate service information. If there are no DTCs in the SCCM, GO to BJ2. No DIAGNOSE the no communication with the SCCM. REFER to DIAGNOSIS AND TESTING . DIAGNOSE the no communication with the SCCM. REFER to DIAGNOSIS AND TESTING . - BJ2 RECHECK THE ABS (ANTI-LOCK BRAKE SYSTEM) MODULE DTCS
- Ignition OFF.
- Put the ABS module in sleep mode by performing the following steps:
- With ALL doors closed, set the ignition from ON to OFF.
- Disconnect the diagnostic scan tool.
- Open the door, exit the vehicle and close the door.
- Wait a minimum of 90 seconds for the ABS module to enter sleep mode.
- Ignition ON.
Are any of the DTCS listed in the Fault Setting Conditions Table retrieved again?
Yes GO to BJ3. No The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition. - BJ3 REVIEW THE RECORDED DTCS FROM THE ABS (ANTI-LOCK BRAKE SYSTEM) MODULE SELF-TEST
- Check the DTCs recorded from the ABS module self-test.
Was DTC U3003:16 or U3003:17 recorded?
Yes REFER to the DIAGNOSTIC TROUBLE CODE (DTC) CHART . No GO to BJ4. - BJ4 CHECK FOR DTCS IN THE SCCM (STEERING COLUMN CONTROL MODULE)
- Record all DTCs from the SCCM self-test.
Are any DTCs present in the SCCM?
Yes DIAGNOSE all SCCM DTCs. REFER to appropriate service information. No GO to BJ5. - BJ5 CHECK FOR OTHER CAUSES OF COMMUNICATION NETWORK CONCERNNOTE: If new modules were installed prior to the DTC being set, the module configuration can be incorrectly set during the PMI or the PMI may not have been carried out.
- Check the vehicle service history for recent service actions related to the SCCM or the ABS module. If recent service history is found:
- Verify the correct replacement module was installed. HVBOM may be used to verify correct part fitment.
- Verify the configuration of replacement module was correct. Re-configure the module using as-built data if prior configuration is suspect.
- Verify the module was not obtained from a like vehicle and installed into customer vehicle. Return the swapped module to source vehicle and obtain new replacement module.
- Operate the system and determine if the observable symptom is still present.
Is the observable symptom still present?
Yes GO to BJ6. No The system is operating correctly at this time. The concern may have been due to incorrect parts replacement procedures or incorrect module configuration. - Check the vehicle service history for recent service actions related to the SCCM or the ABS module. If recent service history is found:
- BJ6 CHECK FOR COMMUNICATION DTCS IN OTHER MODULES
- Ignition ON.
- Press Read Vehicle Information button to retrieve DTCs from the vehicle. NOTE: DTCs may be displayed from previous diagnostic actions.
Is any DTC from the Fault Trigger Conditions Table set in 1 or more modules in addition to the ABS module?
Yes GO to BJ7. No GO to BJ8. - BJ7 VERIFY SCCM (STEERING COLUMN CONTROL MODULE) OPERATION
- Ignition OFF.
- Put the ABS module in sleep mode by performing the following steps:
- With ALL doors closed, set the ignition from ON to OFF.
- Disconnect the diagnostic scan tool.
- Open the door, exit the vehicle and close the door.
- Wait a minimum of 90 seconds for the ABS module to enter sleep mode.
- Disconnect SCCM-A connector.
- Disconnect ABS-A Module connector.
- Disconnect ABS-B Module connector.
- Using a good light source, inspect all disconnected electrical connectors for the following:
- corrosion - install new connector or terminal and clean the module pins
- damaged or bent pins - install new terminals or pins
- pushed-out pins - install new pins as necessary
- spread terminals - install new terminals as necessary
- Connect ABS-A Module connector. Make sure the connector seats and latches correctly.
- Connect ABS-B Module connector. Make sure the connector seats and latches correctly.
- Connect SCCM-A connector. Make sure the connector seats and latches correctly.
- Operate the system and verify the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new SCCM. REFER to appropriate service information. No The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues. - BJ8 VERIFY ABS (ANTI-LOCK BRAKE SYSTEM) OPERATION
- Put the ABS module in sleep mode by performing the following steps:
- With ALL doors closed, set the ignition from ON to OFF.
- Disconnect the diagnostic scan tool.
- Open the door, exit the vehicle and close the door.
- Wait a minimum of 90 seconds for the ABS module to enter sleep mode.
- Disconnect ABS-A Module connector.
- Disconnect ABS-B Module connector.
- Disconnect SCCM-A connector.
- Using a good light source, inspect all disconnected electrical connectors for the following:
- corrosion - install new connector or terminal and clean the module pins
- damaged or bent pins - install new terminals or pins
- pushed-out pins - install new pins as necessary
- spread terminals - install new terminals as necessary
- Connect SCCM-A connector. Make sure the connector seats and latches correctly.
- Connect ABS-A Module connector. Make sure the connector seats and latches correctly.
- Connect ABS-B Module connector. Make sure the connector seats and latches correctly.
- Operate the system and determine if the concern is still present.
Is the concern still present?
Yes The HCU and ABS module are a single assembly known as the EBB unit. Check OASIS for any service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new EBB unit. REFER to: Electric Brake Booster (EBB) . No The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues. - Put the ABS module in sleep mode by performing the following steps: