| B108A:01 |
Start Button: General Electrical Failure |
GO to Pinpoint Test A |
| B108A:24 |
Start Button: Signal Stuck High |
GO to Pinpoint Test A |
| B108A:9E |
Start Button: Stuck On |
GO to Pinpoint Test A |
| B1142:29 |
Ignition Status 1: Signal Invalid |
GO to Pinpoint Test A |
| B1240:11 |
Start Button Mode Indicator: Circuit Short To Ground |
GO to Pinpoint Test B |
| B1240:15 |
Start Button Mode Indicator: Circuit Short To Battery Or Open |
GO to Pinpoint Test B |
| B1240:15 |
Start Button Mode Indicator: Circuit Short To Battery Or Open |
GO to Pinpoint Test C |
| B1310:12 |
Run/Start Control: Circuit Short To Battery |
GO to Pinpoint Test A |
| B1310:14 |
Run/Start Control: Circuit Short To Ground Or Open |
GO to Pinpoint Test A |
| P2534:00 |
Ignition Switch On/Start Position Circuit Low: No Sub Type Information |
GO to Pinpoint Test A |
| P2535:00 |
Ignition Switch On/Start Position Circuit High: No Sub Type Information |
GO to Pinpoint Test A |
| B112B:04 |
Steering Wheel Module: System Internal Failures |
GO to Pinpoint Test D |
| B112B:44 |
Steering Wheel Module: Data Memory Failure |
GO to Pinpoint Test D |
| B112B:45 |
Steering Wheel Module: Program Memory Failure |
GO to Pinpoint Test D |
| B112B:46 |
Steering Wheel Module: Calibration/Parameter Memory Failure |
GO to Pinpoint Test D |
| B112B:49 |
Steering Wheel Module: Internal Electronic Failure |
GO to Pinpoint Test D |
| B135C:11 |
Heater Element: Circuit Short To Ground |
GO to Pinpoint Test G |
| B135C:13 |
Heater Element: Circuit Open |
GO to Pinpoint Test G |
| U0126:87 |
Lost Communication With Steering Angle Sensor Module: Missing Message |
GO to Pinpoint Test D |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test H |
| U0146:00 |
Lost Communication With Serial Data Gateway 'A': No Sub Type Information |
GO to Pinpoint Test H |
| U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test H |
| U023A:00 |
Lost Communication With Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test H |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test H |
| U053B:00 |
Invalid Data Received From Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test H |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test I |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test I |
| U210A:11 |
Temperature Sensor: Circuit Short To Ground |
GO to Pinpoint Test G |
| U210A:13 |
Temperature Sensor: Circuit Open |
GO to Pinpoint Test G |
| U210A:29 |
Temperature Sensor: Signal Invalid |
GO to Pinpoint Test G |
| U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test D |
| U3003:A2 |
Battery Voltage: System Voltage Low |
GO to Pinpoint Test E |
| U3003:A3 |
Battery Voltage: System Voltage High |
GO to Pinpoint Test F |