Parking Brake System DTCS
Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| B1111: 4B | Electric Park Brake Enable: Over Temperature | GO to Pinpoint Test F |
| B1111: 53 | Electric Park Brake Enable: Deactivated | GO to Pinpoint Test G |
| B1111: 54 | Electric Park Brake Enable: Missing Calibration | GO to Pinpoint Test E |
| C0609: 01 | Park Brake Switch Circuit: General Electrical Failure | GO to Pinpoint Test B |
| C0616: 9A | Park Brake Control Module Control Circuit Performance: Component or System Operating Conditions | GO to Pinpoint Test B |
| C1034: 01 | Park Brake: General Electrical Failure | GO to Pinpoint Test B |
| C1034: 07 | Park Brake: Mechanical Failures | GO to Pinpoint Test K |
| C1034: 13 | Park Brake: Circuit Open | GO to Pinpoint Test B |
| C1034: 25 | Park Brake: Signal Shape/Waveform Failure | GO to Pinpoint Test B |
| C1034: 2F | Park Brake: Signal Erratic | GO to Pinpoint Test B |
| C1034: 47 | Park Brake: Watchdog/Safety μC Failure | GO to Pinpoint Test B |
| C1034: 48 | Park Brake: Supervision Software Failure | GO to Pinpoint Test B |
| C1034: 57 | Park Brake: Invalid/Incompatible Software Component | GO to Pinpoint Test B |
| C1034: 71 | Park Brake: Actuator Stuck | GO to Pinpoint Test C |
| C1034: 77 | Park Brake: Commanded Position Not Reachable | GO to Pinpoint Test C |
| C1034: 78 | Park Brake: Alignment Or Adjustment Incorrect | GO to Pinpoint Test H |
| C1034: 97 | Park Brake: Component or System Operation Obstructed or Blocked | GO to Pinpoint Test D |
| C1A43: 98 | Motor Supply: Component or System Over Temperature | GO to Pinpoint Test D |
| C2005: 18 | Right Actuator: Circuit Current Below Threshold | GO to Pinpoint Test D |
| C2005: 19 | Right Actuator: Circuit Current Above Threshold | GO to Pinpoint Test D |
| C2005: 77 | Right Actuator: Commanded Position Not Reachable | GO to Pinpoint Test C |
| C2005: 78 | Right Actuator: Alignment Or Adjustment Incorrect | GO to Pinpoint Test A |
| C2006: 18 | Left Actuator: Circuit Current Below Threshold | GO to Pinpoint Test D |
| C2006: 19 | Left Actuator: Circuit Current Above Threshold | GO to Pinpoint Test D |
| C2006: 77 | Left Actuator: Commanded Position Not Reachable | GO to Pinpoint Test C |
| C2006: 78 | Left Actuator: Alignment Or Adjustment Incorrect | GO to Pinpoint Test A |
| C2007: 13 | Right Motor: Circuit Open | GO to Pinpoint Test D |
| C2007: 1C | Right Motor: Circuit Voltage Out Of Range | GO to Pinpoint Test D |
| C2007: 92 | Right Motor: Performance Or Incorrect Operation | GO to Pinpoint Test D |
| C2008: 13 | Left Motor: Circuit Open | GO to Pinpoint Test D |
| C2008: 1C | Left Motor: Circuit Voltage Out Of Range | GO to Pinpoint Test D |
| C2008: 92 | Left Motor: Performance Or Incorrect Operation | GO to Pinpoint Test D |
| U2002: 00 | Switch: No Sub Type Information | GO to Pinpoint Test J |
| U2002: 47 | Switch: Watchdog/Safety μC Failure | GO to Pinpoint Test B |